DIOTEC ELECTRONICS CORP.
18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958
Data Sheet No. BRDB-2500P-1C ADBD-2500P-1C
25 AMP SILICON BRIDGE RECTIFIERS
FEATURES MECHANICAL SPECIFICATION
SERIES: DB2500P - DB2510P and ADB2504P - ADB2508P
VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM MECHANICAL STRENGTH AND HEAT DISSIPATION (Solder Voids: Typical < 2%, Max. < 10% of Die Area) BUILT-IN STRESS RELIEF MECHANISM FOR SUPERIOR RELIABILITY AND PERFORMANCE INTEGRALLY MOLDED HEAT SINK PROVIDES VERY LOW THERMAL RESISTANCE FOR MAXIMUM HEAT DISSIPATION
Heat Sink
BH
Heat Sink
BH
Molded Body
LT
LL
Molded Body
LD
D1
HOLE FOR #8 SCREW
HOLE FOR #8 SCREW
UL RECOGNIZED - FILE #E124962
+
AC
D3 BL
)+ )+
+ _
RoHS COMPLIANT
MECHANICAL DATA
AC
BL D1
+
D1
AC
D2
_
_
AC
D1 BL
D2
Case: Case: Molded epoxy with integral heat sink Epoxy carries a U/L Flammability rating of 94V-0 Terminals: Round silver plated copper pins or fast-on terminals Soldering: Per MIL-STD 202 Method 208 guaranteed Polarity: Marked on side of case Mounting Position: Any. Through hole for #8 screw. Max. mounting torque = 20 in-lb. Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams) Wire Leads - 0.55 Ounces (16.0 Grams)
SYM BL BH D1 D2 D3 LT
BL
MILLIMETERS MIN
INCHES
SYM BL BH D1 D2 LL
MILLIMETERS MIN
INCHES
28.4
9.6 15.7 17.5 13.5 n/a
MAX 28.7 10.2 16.7 18.5 14.5
MIN
1.12 0.38 0.62 0.69 0.53 n/a
MAX 1.13 0.40 0.66 0.73 0.57 0.6
28.4
9.6 17.5 10.9 20.6
MAX 28.7 10.2 18.5 11.9 n/a
MIN
1.12 0.38 0.69 0.43 0.81 0.039
MAX 1.13 0.40 0.73 0.47 n/a
15.2
LD
1.0
1.1
0.042
Suffix "T" indicates FAST-ON TERMINALS
Suffix "W" indicates WIRE LEADS
MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.
PARAMETER (TEST CONDITIONS)
Series Number Maximum DC Blocking Voltage Working Peak Reverse Voltage Maximum Peak Recurrent Reverse Voltage RMS Reverse Voltage Peak Forward Surge Current. Single 60Hz Half-Sine Wave Superimposed on Rated Load (JEDEC Method). TJ = 125O C Average Forward Rectified Current @ TC = 75 C
Junction Temperature Range Storage Temperature Range Mimimum Avalanche Voltage Maximum Avalanche Voltage Maximum Forward Voltage (Per Diode) at 12.5 Amps DC
o o
RATINGS
SYMBOL
CONTROLLED AVALANCHE
NON-CONTROLLED AVALANCHE
UNITS
ADB ADB ADB DB DB DB DB DB DB DB 2504P 2506P 2508P 2500P 2501P 2502P 2504P 2506P 2508P 2510P
VRM VRWM VRRM VR (RMS) IFSM IO TJ TSTG V(BR) Min V(BR) Max VFM IRM VISO RGJC @ TA = 25 C o @TA = 125 C
See Note 1 See Note 1 1.05 1 50 2500 1.2
o
400
600
800
50
100
200
400
600
800 1000
VOLTS
280
420
560
35
70
140 500 25
280
420
560
700
AMPS
-55 to +150 -55 to +150 n/a n/a
°C
VOLTS
Maximum Reverse Current at Rated VRM
mA VOLTS C/W
3.01 25dbp
Minimum Insulation Breakdown Voltage (Circuit to Case) Typical Thermal Resistance, Junction to Case
NOTES: (1) These bridges exhibit the avalanche characteristic at breakdown. If your application requires a specific breakdown voltage range, please contact us.
E41
DIOTEC ELECTRONICS CORP.
18020 Hobart Blvd., Unit B Gardena, CA 90248 U.S.A Tel.: (310) 767-1052 Fax: (310) 767-7958
Data Sheet No. BRDB-2500P-2C ABDB-2500P-2C
25 AMP SILICON BRIDGE RECTIFIERS
RATING & CHARACTERISTIC CURVES FOR SERIES DB2500P - DB2510P and SERIES ADB2504P - ADB2508P
30
1000
Peak Forward Surge Current (Amperes)
Average Forward Current, Io (Amperes)
25
60Hz Resistive or Inductive Loads
TJ = 125 C
o
20
15
Bridge Mounted on 5 x 6 x 4.9" Thick (12.7 x 15.2 x 12.4cm) Finned Al. Plate
10
5
50
0
1
10
100
0
50
75
100
125
150
Case Temperature, C FIGURE 1. FORWARD CURRENT DERATING CURVE
o
Number of Cycles at 60 Hz FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
1000
10
TJ = 125 C
O
Instantaneous Forward Current (Amperes)
Instantaneous Reverse Current, I (Microamperes)
100
1.0
10
1.0
TJ = 25 C Pulse Width = 300mSec 1%Duty Cycle
o
0.1
TJ = 25 C
O
0.1 0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
.01
0 20 40 60 80 100 120 140
Instantaneous Forward Voltage (Volts) FIGURE 3. TYPICAL FORWARD CHARACTERISTIC PER DIODE
Percent of Rated Peak Reverse Voltage FIGURE 4. TYPICAL REVERSE CHARACTERISTICS
E42
3.01 25db
很抱歉,暂时无法提供与“ADB2508P”相匹配的价格&库存,您可以联系我们找货
免费人工找货