03GENW3ES

SNAP-IN MOUNTING HIGH PERFORSERIES MANCE IEC CONNECTOR FILTERS SPECIFICATIONS 1. Maximum leakage current each line-to-ground @ 115VAC 60Hz: 0.2mA @ 250VAC 50Hz: 0.4mA 2. Hipot rating (one minute) line-to-ground: 2250VDC line-to-line: 1450VDC 3. Operating frequency: 50/60Hz 4. Rated voltage: 115/250VAC COMPONENTS PART NO. INSERTION LOSS (TYPICAL) Cx (uF) 01GENG3E/W3E/-R 03GENG3E/W3E/-R 03GENG3U/-R 03GENW3ES/-R 03GENG3Q/W3Q/-R 06GENG3E/W3E/-R 06GENG3U/-R 06GENG3Q/W3Q/-R 06GENW3ES/-R 10GENG3E/W3E/-R 10GENG3C/W3C/-R 10GENG3Q/W3Q/-R 0.1 ** 10GENG3U/-R ** *** Cy (pF) R( ) 03GENG3E 06GENG3E 6.5 2.5 2.5 2.5 4 0.8 0.8 1.5 0.8 0.2 0.4 0.3 * ** *** 2200 1M 40 dB 20 dB 0 dB 20GENG3E N Cy Cx Cy G 100K 1M COMMON MODE 10M DIFF.MODE 80 dB 60 dB 10 40 40 40 40 35 30 32 35 30 30 40 40 40 55 40 35 45 40 35 40 dB 20 dB 0 dB ELECTRICAL SCHEMATIC R 10K UL, CSA approved to 13A 115/250V VDE approved to 10A/250V VDE approved to 16A/250V COMMON MODE (L-G) IN 50 OHM SYSTEM CURRENT FREQUENCY-MHz RATING .15 .50 1.0 5.0 1A 28 35 38 38 3A 20 25 30 38 6A 12 18 24 35 6A (G3Q) 15 20 24 35 10A 4 10 13 28 10A (G3C) 10 15 15 25 10A (G3Q) 10 12 15 30 15A 4 10 13 28 20A 8 10 15 25 L I N E DIFF. MODE DIFF. MODE 60 dB MINIMUM INSERTION LOSS IN dB L COMMON MODE COMMON MODE 80 dB 0.3 0.2 0.2 0.3 10GENW3ES/-R 15GENG3E/W3E/-R 20GENG3E/W3E/-R UL, CSA approved to 4A 115/250V UL, CSA approved to 8A 115/250V VDE approved to 8A/250V L (mH) L' L O A D N' G' R: 1M /-R ONLY 2-7 10K 100K OR IEC INLET FILTERS INTRODUCTIONS 1. Snap-in mounting type to reduce labor cost. Compact and reliable at low cost. 2. Bleeder resistor can be added with suffix "-R" on part numbers, except G3H,G3V,W3V,G3J,W3J,types. 3. Optional side snap-in mounting clip type with suffix (H) on part numbers. 4. All part numbers are UL recognized, CSA certified and VDE approved. 5. With optional Y-Cap from 100pF to 3300pF. V D E 1M 10M PANEL Suggested thickness of mounting panel is from 0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout PCB ASSEMBLY FROM FRONT MECHANICAL CONSTRUCTION L 0.84MAX. 21.4MAX. 0.945 0.02 24.0 0.5 1.22 0.02 31.0 0.5 N 0.862 0.004 21.9 0.1 1.66MAX. 42.16MAX. 2.1MAX. 53.4MAX. R0.08MAX. R2.0MAX. +0.012 1.12 - 0 +0.3 28.45 - 0 0.0315~0.06 0.8~1.6 SUGGESTED MOUNTING CUTOUT NG3E, NG3C, NG3Q (Optional wire type) 1.12 MAX. 28.4 MAX. GENG3E L 0.84MAX. 21.4MAX. 0.945 0.02 24.0 0.5 1.22 0.02 31.0 0.5 N +0.04 0.142 - 0.02 +1.0 3.6 - 0.5 G 0.85 0.004 21.5 0.1 2.1MAX. 53.4MAX. 1.66MAX. 42.16MAX. R0.08MAX(2X) R2.0MAX 1.16 0.004 29.5 0.1 0.0315~0.063 0.8~1.6 SUGGESTED MOUNTING CUTOUT NG3E(H), NG3C(H), NG3Q(H) (Optional wire type) 1.12 MAX. 28.4 MAX. GENG3E(H) L 0.8 0.02 20.4 0.5 0.945 0.02 24.0 0.5 1.22 0.02 31.0 0.5 N 0.862 0.004 21.9 0.1 0.5 38.0 1.94 0.04 49.4 1.0 1.50 0.02 +0.04 0.11- 0.02 +1.0 2.8- 0.5 G R0.08MAX. R2.0MAX. +0.012 1.12 - 0 +0.3 28.45 - 0 0.0315~0.06 0.8~1.6 SUGGESTED MOUNTING CUTOUT NG3U (With Compact Size) 1.10 0.02 28.0 0.5 31.0 0.5 1.12 MAX. 0.84MAX. 21.3MAX. 24.0 0.5 +0.012 1.12 - 0 +0.3 28.45 - 0 R0.08MAX. R2.0MAX. 0.0315~0.06 0.8~1.6 SUGGESTED MOUNTING CUTOUT BLUE NW3ES G/Y BROWN 28.4 MAX. 0.862 0.004 21.9 0.1 1.22 0.2 +0.04 0.142 -0.02 +1.0 3.6 -0.5 N G 1.575 MAX. 40.0 MAX. L 0.945 0.02 NG3U NW3ES 2.60MAX. 66.0MAX. 1.496MAX. 38.0MAX. 1.18 30.0 0.138 3.5 1.04MAX. 26.5MAX. 3.19MAX. 81.0MAX. 20GENG3E (Optional wire type) +0.02 1.043-0 +0.5 26.5-0 0.248X0.031 6.3X0.8 1.36MAX. 34.5MAX. IEC INLET FILTERS +0.04 0.142 - 0.02 +1.0 3.6 - 0.5 G R0.118MAX. R4.0MAX. +0.02 1.417-0 +0.5 36.0-0 SUGGESTED MOUNTING CUTOUT (MOUNTING FROM REVERSE) WIRE LENGTH : 4.0" MIN. 2-8 UNIT: INCH mm