03KENG3EA

HIGH PERFORMANCE SNAP-IN SERIES FILTERS 0.84MAX. 21.4MAX. G3SA 1.22 0.02 31.5 0.5 0.84 MAX. 21.3 MAX. +0.012 1.12-0 +0.3 28.45-0 ELECTRICAL SCHEMATIC Cy Cx L Cy L O A D 0.0315~0.063 0.8~1.6 WIRE LENGTH : 4.0" MIN. W3EA N' N R0.08MAX. R2.0MAX. SUGGESTED MOUNTING CUTOUT 4.0MIN. 100.0MIN. L' R 21.90 0.1 0.862 0.004 N G 0.945 0.02 Suggested thickness of mounting panel is from 0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout 1.12MAX. 28.4MAX. L 0.0315~0.063 0.8~1.6 SUGGESTED MOUNTING CUTOUT 1.12MAX. 28.4MAX. L 45 50 50 40 40 45 R0.08MAX. R2.0MAX. +0.04 0.14-0.02 +1.0 3.6-0.5 30 45 50 50 40 40 45 +0.012 1.12-0 +0.3 28.45-0 1.89MAX. 48.0MAX. 1.97 0.04 50.0 1.0 COMMON MODE (L-G) IN 50 OHM SYSTEM FREQUENCY-MHz PART NO. .15 .50 1.0 5.0 10 03KENG3EA/03KENW3EA 15 20 25 40 40 08KENG3EA/08KENW3EA 10 15 20 35 40 10KENG3EA/10KENW3EA 7 12 18 30 30 03KENG3SA/03KENW3SA 15 20 25 40 40 06KENG3SA/06KENW3SA 7 15 20 35 40 10KENG3SA/10KENW3SA 4 12 18 30 30 DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM 03KENG3EA/03KENW3EA 5 12 15 40 50 08KENG3EA/08KENW3EA 5 10 15 45 40 10KENG3EA/10KENW3EA 4 12 18 30 30 10 20 35 40 45 03KENG3SA/03KENW3SA 10 25 40 35 40 06KENG3SA/06KENW3SA 10 25 35 30 30 10KENG3SA/10KENW3SA 1.66MAX. 42.16MAX. MINIMUM INSERTION LOSS IN dB 21.90 0.1 * VDE approved to 6A 250V. ** UL, CSA & VDE approved to 9A 115/250 VAC. 0.862 0.004 +0.04 0.14-0.02 +1.0 3.6-0.5 1.22 0.02 31.5 0.5 24.0 0.5 0.945 0.02 N G 2.1MAX. 53.4MAX. L 24.0 0.5 L (mH) Cx (uF) Cy (pF) Lg (uH) 3.1 0.8 0.4 0.1 2200 100 3.1 0.8 0.4 1. Maximum leakage current each line-to-ground @ 115VAC 60Hz: 0.20mA @ 250VAC 50Hz: 0.40mA 2. Hipot rating (one minute) line-to-ground: 2250VDC line-to-line: 1450VDC 3. Operating frequency: 50/60Hz 4. Rated voltage: 115/250VAC G' G 1.89MAX. 48.0MAX. +0.04 0.14-0.02 +1.0 3.6-0.5 1.22 0.02 31.5 0.5 G3EA 21.3MAX. MECHANICAL CONSTRUCTION +0.012 1.12-0 +0.3 28.45-0 W3EA 21.90 0.1 N G 0.862 0.004 L 24.0 0.5 R: 1M /-R ONLY 0.945 0.02 Lg 2.32 MAX. 59.0 MAX. IEC INLET FILTERS COMPONENTS L I N E OR SPECIFICATIONS INTRODUCTIONS 1. Specially designed with ground choke providing most effective EMI suppression for high frequency noise (ranged 5MHz-25MHz). 2. Bleeder resistor can be added with suffix "-R" on part numbers. 3. With optional Y capacitor from 100pF to 3300pF. 4. All part numbers are UL recognized, CSA certified and VDE approved. 5.Optional side snap-in mounting clip type with suffix (H) on part numbers. for 03/06/10KENG3SA series. PART NO. 03KENG3EA/03KENW3EA * 08KENG3EA/08KENW3EA ** 10KENG3EA/10KENW3EA 03KENG3SA/03KENW3SA 06KENG3SA/06KENW3SA 10KENG3SA/10KENW3SA V D E R0.08MAX. R2.0MAX. 0.0315~0.063 0.8~1.6 SUGGESTED MOUNTING CUTOUT 1.12MAX. 28.4MAX. 2-12 G3EA UNIT: INCH mm