06GEEG3QM

DE & GESERIES IEC INLET FILTERS SPECIFICATIONS INTRODUCTIONS 1. Maximum leakage current each line-to-ground: @ 115VAC 60Hz: 2uA @ 250VAC 50Hz: 5uA 2. Hipot rating (one minute) line-to-ground: 2250VDC line-to-line: 1450VDC 3. Operating frequency: 50/60Hz 4. Rated voltage: 115/250VAC 1. DE & GE Series filters are for UL 544 & UL 2601 health care equipment. 2. DE Series: UL, CSA, VDE. 3. GE Series: UL, CSA, VDE. 4. GE Series is with optional bleeder resistor and wire connection. COMPONENTS * * * PART NO. 01DEEG3BM 03DEEG3BM 06DEEG3BM 10DEEG3BM 03GEEG3QM/W3QM 03GENG3QM/W3QM 06GEEG3QM/W3QM 06GENG3QM/W3QM 10GEEG3QM/W3QM 10GENG3QM/W3QM 20GEEG3EM/W3EM 20GENG3EM/W3EM Cx (uF) L (mH) 5 1.8 0.6 0.18 0.033 ELECTRICAL SCHEMATIC 4.0 1.5 0.1 L' L 0.3 Cx L I N E UL, CSA approved to 4A 115/250V UL, CSA approved to 8A 115/250V UL, CSA approved to 13A 115/250V VDE approved to 16A 250V R L O A D L N' N (R:1M G ) G' DE, GE SERIES MINIMUM INSERTION LOSS IN dB COMMON MODE (L-G) IN 50 OHM SYSTEM 25 25 20 18 5 6A 15 20 20 20 20 12 10A 6 8 10 10 10 6 20A 8 10 12 12 10 6 MECHANICAL CONSTRUCTION 1.52 0.13 3.3 1.95 49.5 2.10 53.3 52.1 2.05 L 1.12 28.4 38.6 SUGGESTED MOUNTING CUTOUT (MOUNTING FROM REVERSE) +0.02 0.85-0 21.6 0.84 21.3 1.575 EG3BM EG3QM (optional wire type) R0.12 R3.0 01, 03, 06,10DEEG3BM 03, 06, 10GEE3QM 7-1 40.01 18 1.575 0.02 3A G 01DEEG3BM 03DEEG3BM 06DEEG3BM 10DEEG3BM 03GEEG3QM/W3QM 03GENG3QM/W3QM 06GEEG3QM/W3QM 06GENG3QM/W3QM 10GEEG3QM/W3QM 10GENG3QM/W3QM 20GEEG3EM/W3EM 20GENG3EM/W3EM CURRENT FREQUENCY-MHz RATING 0.15 0.15 0.15 0.15 0.15 0.15 10 10 25 30 40 30 1A 12 20 18 25 25 30 3A 15 25 8 20 24 26 6A 5 20 3 7 12 14 10A N TYPE 0.005 40.1 M3 +0.02 1.12-0 28.45 UNIT: INCH mm MECHANICAL CONSTRUCTION 0.862 0.004 21.90 0.1 +0.04 0.142 -0.02 1.66 MAX. 42.16 MAX. 3.6 -0.5 1.22 0.02 31.0 0.5 2.08 MAX. 52.83 MAX. G +1.0 0.945 24.0 N 0.84MAX. 21.4MAX. L 0.02 0.5 ALL WIRE LEADS 4.0" LONG MIN. +0.012 1.12 -0 R0.08MAX. R2.0MAX. +0.3 28.45 -0 SUGGESTED MOUNTING CUTOUT L' G' N' 1.12 MAX. 28.4 MAX. NG3QM (Optional wire type) SUGGESTED THICKNESS OF MOUNTING PANEL IS FROM 0.04 (1.0) TO 0.063 (1.6) INCH (mm) OF MOUNTING CUTOUT 0.945 0.02 24.0 0.5 0.85 0.004 21.5 0.1 R0.08MAX(2X) R2.0MAX 1.16 0.004 29.5 0.1 +0.04 0.142 -0.02 +1.0 3.6 -0.5 NG3QM(H) (Optional wire type) 0.03 ~ 0.063 0.76 ~ 1.6 SUGGESTED MOUNTING CUTOUT SUGGESTED THICKNESS OF MOUNTING PANEL IS FROM 0.04 (1.0) TO 0.063 (1.6) INCH (mm) OF MOUNTING CUTOUT 2.08 MAX. 52.83 MAX. 1.66 MAX. 42.6 MAX. 1.22 0.2 31.0 0.5 1.12 MAX. 28.4 MAX. 0.84 MAX. 21.3 MAX. 0.138 3.5 1.18 30.0 2.09 53.0 1.36 MAX. 34.5 MAX. 1.654 42.0 2.60 MAX. 66.0 MAX. 0.248X0.031 6.3X0.8 0.138 3.5 1.654 0.004 42.0 0.1 1.04 MAX. 26.5 MAX. +0.02 1.043-0 +0.5 26.5-0 3.19 MAX. 81.0 MAX. M3 R0.157 MAX. R4.0 MAX. 20GEEG3E (Optional wire type) +0.5 34.5-0 +0.02 1.358-0 SUGGESTED MOUNTING CUTOUT (MOUNTING FROM REVERSE) 2.60 MAX. 66.0 MAX. 1.18 30.0 1.36 MAX. 34.5 MAX. 0.248X0.031 6.3X0.8 1.04 MAX. 26.5 MAX. 20GENG3E (Optional wire type) SUGGESTED THICKNESS OF MOUNTING PANEL IS FROM 0.04 (1.0) TO 0.063 (1.6) INCH (MM) OF MOUNTING CUTOUT 7-2 +0.02 1.043-0 +0.5 26.5-0 0.138 3.5 3.19 MAX. 81.0 MAX. R0.118 MAX. R3.0 MAX. +0.5 36.0-0 +0.02 1.417-0 SUGGESTED MOUNTING CUTOUT (MOUNTING FROM REVERSE) UNIT: INCH mm