AFB0824SH7DT

客戶承認書 TI AL SPECIFICATION FOR APPROVAL EN CUSTOMER: DESCRIPTION: DC FAN DELTA MODEL: REV: AFB0824SH7DT REV: 01 12/13/2017 CO NF SAMPLE ISSUE DATE: QUANTITY: ID CUSTOMER P/N: A PLEASE SIGN BACK ONE COPY OF THIS SPECIFICATION AFTER COMPLETION OF APPROVAL DE LT APPROVED BY: DATE: B DELTA ELECTRONICS COMPONENTS (WUJIANG) LTD. FAN/MOTOR PLANT No.1688 Jiangxing East Road,WuJiang Economy Development Zone Wujiang City JiangSu Province, P.R.C. TEL:86-512-63406008 FAX:86-512-63015608 DE LT A DO C CE ER NT LT DE A L TI A EN NF ID CO LT DE A L TI A EN NF ID CO LT DE A L TI A EN NF ID CO LT DE A L TI A EN NF ID CO LT DE A L TI A EN NF ID CO Application Notice 1. Delta will not guarantee the performance of the products if the application condition falls outside the parameters set forth in the specification. 2. A written request should be submitted to Delta prior to approval if deviation from this specification is required. 3. Please exercise caution when handling fans. Damage may be caused when pressure is applied to the impeller, if the fans are handled by the lead wires, or if the fan was hard-dropped to the production floor. 4. Except as pertains to some special designs, there is no guarantee that the products will be free from any such safety problems or failures as caused by the introduction of powder, droplets of water or encroachment of insect into the hub. 5. The above-mentioned conditions are representative of some unique examples and viewed as the first point of reference prior to all other information. 6. It is very important to establish the correct polarity before connecting the fan to the power source. Positive (+) and Negative (-). Damage may be caused to the fans if connection is with reverse polarity, if there is no foolproof method to protect against such error specifically mentioned in this spec. 7. Delta fans without special protection are not suitable where any corrosive fluids are introduced to their environment. 8. Please ensure all fans are stored according to the storage temperature limits specified. Do not store fans in a high humidity environment. We highly recommend performance testing is conducted before shipping, if the fans have been stored over 6 months. 9. Not all fans are provided with the Lock Rotor Protection feature. If you impair the rotation of the impeller for the fans that do not have this function, the performance of those fans will lead to failure. 10. Please be cautious when mounting the fan. Incorrect mounting of fans may cause excess resonance, vibration and subsequent noise. 11. It is important to consider safety when testing the fans. A suitable fan guard should be fitted to the fan to guard against any potential for personal injury. 12. Except where specifically stated, all tests are carried out at room (ambient) temperature and relative humidity conditions of 25oC, 65% RH. The test value is only for fan performance itself. 13. Be certain to connect an “ 4.7µF or greater” capacitor to the fan externally when the application calls for using multiple fans in parallel, to avoid any unstable power. Doc. No: FMBG-ES Form 001 Rev. 01 Date: June 24, 2009 CERTIFICATE OF COMPLIANCE Certificate Number Report Reference Issue Date Issued to: This is to certify that representative samples of 20151020-E132003 E132003-19971216 2015-OCTOBER-20 DELTA ELECTRONICS INC 252 SHANG YING RD KUEI SHAN TAOYUAN HSIEN 333 TAIWAN COMPONENT - FANS, ELECTRIC See addendum page Have been investigated by UL in accordance with the Standard(s) indicated on this Certificate. Standard(s) for Safety: Electric Fans, UL 507 Fans and Ventilators, CSA C22.2 No. 113 Additional Information: See the UL Online Certifications Directory at www.ul.com/database for additional information Only those products bearing the UL Certification Mark should be considered as being covered by UL's Certification and Follow-Up Service. Recognized components are incomplete in certain constructional features or restricted in performance capabilities and are intended for use as components of complete equipment submitted for investigation rather than for direct separate installation in the field. The final acceptance of the component is dependent upon its installation and use in complete equipment submitted to UL LLC. Look for the UL Certification Mark on the product. Bruce Mahrenholz, Director North American Certification Program UL LLC Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, please contact a local UL Customer Service Representative at http://ul.com/aboutul/locations/ Page 1 of 2 CERTIFICATE OF COMPLIANCE Certificate Number Report Reference Issue Date 20151020-E132003 E132003-19971216 2015-OCTOBER-20 This is to certify that representative samples of the product as specified on this certificate were tested according to the current UL requirements. Model Nos. AFB0305LLA, AFB0305LA, AFB0305MA, AFB0305HA, AFB0405LA, AFB0405MA, AFB0405HA, AFB0405HHD, AFB0505LA, AFB0505MA, AFB0505HA, AFB02505LA, AFB02505MA, AFB02505HA, AFB02505HHA, AFB0705L, AFB0705M, AFB0705H, AFB0405LD, AFB0405MD, AFB0405HD, AFB0605LLD, AFB0605LB, AFB0605MB, AFB0605HB, AFB0605HHB, AFB0605LA, AFB0605MA, AFB0605HA, AFB0505LB, AFB0505MB, AFB03505LA, AFB03505MA, AFB03505HA, AFB0505HB, AFB0512LB, AFB0512MB, AFB0512HB, AFB0512HHB, AFB0412LA, AFB0412MA, AFB0412HA, AFB0412HHA, AFB0512LA, AFB0512MA, AFB0512HA, AFB0712LA, AFB0712MA, AFB0712HA, AFB0712HHA, AFB0712VHA, AFB0812LL, AFB0812L, AFB0812M, AFB0812H, AFB0812HH, AFB0812VH, AFB0812SH, AFB0812LLB, AFB0812LB, AFB0812MB, AFB0812HB, AFB0812HHB, AFB0812VHB, AFB0812SHB, AFC0812D, AFC0812DD(Y), AFB0912L, AFB0912M, AFB0912H, AFB0912HH, AFB0912VH, AFC0912D, AFB0612LA, AFB0612MA, AFB0612HA, AFB02512LA, AFB02512VHB-5B05(Y), AFB02512MA(Y), AFB02512HA(Y), AFB02512HHA(Y), AFB0312LA(Y), AFB0312MA(Y), AFB0312HA(Y), AFB03512LA(Y), AFB03512MA(Y), AFB03512HA(Y), AFB0612LB, AFB0612MB, AFB0612HB, AFB0612HHB, AFB0612LLD, AFB02512MA-A(Y), AFB02512HA-A(Y), AFB02512HHA-A(Y), AFB0312LA-A(Y), AFB0312MA-A(Y), AFB0312HA-A(Y), AFB0612LD, AFB0612MD, AFB0612HD, AFB0612HHD, AFB0612VHD, AFB0612VHB, WFB1212VHE, WFB1212ME, AFB0412LD, AFB0412MD, AFB0412HD, AFB0412HHD, AFB0312LLA, AFB0524LB, AFB0524MB, AFB0524HB, AFB0524HHB, AFB0824LL, AFB0824L, AFB0824M, AFB0824H, AFB0824HH, AFB0824VH, AFB0824SH, AFB0824LLB, AFB0824LB, AFB0824MB, AFB0824HB, AFB0824HHB, AFB0824VHB, AFB0824SHB, AFB0924L, AFB0924M, AFB0924H, AFB0924HH, AFB0924VH, AFB0624LB, AFB0624MB, AFB0624HB, AFB0624HHB, AFB0624LLD, AFB0624LD, AFB0624MD, AFB0624HD, AFB0624HHD, AFB0624VHD, AFB0624VHB, WFB1224VHE, WFB1248HHE, WFB1248VHE, AFB0424LD, AFB0424MD, AFB0424HD, AFB0424HHD, AFB0748L, AFB0748M, AFB0748H, AFB0748HH, AFB0848L, AFB0848M, AFB0848H, AFB0848HH, AFB0948L, AFB0948M, AFB0948H, AFB0948HH, AFB0648L, AFB0648M, AFB0648H, AFB0648HH, AFB0648VH, AFB0648SH, AFB0648EH, AFB04512LB(Y), AFB04512MB(Y), AFB04512HB(Y), AFB0512LB-A(Y), AFB0512MB-A(Y), AFB0512HB-A(Y), GFB1412EHT(Y), GFC1412DT(Y), AFB0748SH-SP(Y), BFB1712EHT(Y), AFB03512LA-A(Y),AFB03512MA-A(Y),AFB03512HA-A(Y) Note: above (Y) may be xxxxx, where x may be A through Z, 0 through 9, “-“ or blank. For Models AFB0812SH(Y), the (Y) excluded -9N07 and –SM26 Bruce Mahrenholz, Director North American Certification Program UL LLC Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, please contact a local UL Customer Service Representative at http://ul.com/aboutul/locations/ Page 2 of 2