FHS-A6025B00

Model Name: FHS-A6025B00 DELTA ELECTRONICS, INC. Application: • Intel Nehalem Socket 1366 2U • Xeon (45nm) E5500/L5500 CPU sequence Pictures Thermal & Mechanical Spec.: • Thermal performance for 80W CPU • HSK Assembly Weight: 500 g (ref.) • Clipping Force: 16 Kgf (ref.) θca (℃/W) 1. Heat Sink Type: Extrude HSK Material: Aluminum A6063 or Equivalent. Dimension: 90*90*64 mm 2. Thermal interface material 2 Material: Dow Corning TC-5630 or Equivalent. 3. Fan Thermal Performance Curve (60x60x25 mm with PWM Control) 0.38 60.00 Rated Voltage: 12 V 0.36 55.00 Life Time: 0.34 50.00 Two ball bearing 80000 hrs Connector: 0.32 45.00 a. Lead wire: UL 1061 AWG#26 0.30 40.00 pin 1: black wire--------(-) 0.28 35.00 pin 2: yellow wire----------(+) 3000 4000 5000 6000 7000 THERMAL RESISTANCE pin 3: green wire---------(F00) Speed (rpm) Noise pin 4: blue wire------------(PWM) * All readings are typical values at rated voltage. b. Housing: Molex 47054-1000 or equivalent c. Terminal: Molex 2759T 08-50-0113 or equivalent Noise (dBA) Component Specification: * Specifications are subject to change without notice DELTA ELECTRONICS, INC. 252, Shang Ying Road, Kuei San TAOYUAN SHIEN 333, TAIWAN,R.O.C. TEL: 886-3-3591968 EXT 2073 FAX: 886-3-3591991 DELTA PRODUCTS CORPORATION 4405 CUSHING PARKWAY FREMONT, CA 94538, U.S.A. TEL: 1-510-668-5100 FAX: 1-510-668-0680 DELTA ELECTRONICS(JAPAN), INC. DELTA SHIBADAIMON BLDG. 2-1-14 SHIBADAIMON, MINATO-KU, TOKYO, 105-0012, JAPAN TEL: 81-3-5733-1111 FAX: 81-3-5733-1211 DELTA ELECTRONICS EUROPE LTD. 2 YOUNG PLACE KELVIN INDUSTRIAL ESTATE EAST KILBRIDE, GLASGOW G75 OTD, U.K. TEL: 44-1355-588888 FAX: 44-1355-588889 Date: 27-Apr-07 Delta Electronics Corp. APPROVAL SHEET Customer Name .: Model Name.: COOLER Delta Part No.: FHS-A6025B00 Customer Part No.: Spec Issue Date .: Spec Revision : 12/31/2015 02 PLEASE SEND ONE COPY OF THIS SPECIFICATION BACK AFTER YOU SIGNED APPROVAL FOR PRODUCTION PRE-ARRANGMENT. Approved By: Date: Approval Form No.︰tMP—D029 Check Designer Form Rev.︰00 Delta Electronics Corp. REV. Description Drawn 00 ISSUE SPEC Skyler-Huang01/05’10 01 1. CHANGE THE FAN P/N FROM 3620927211 TO 3620936511 2. CHANGE THE FAN LABEL P/N FROM 3266498200 TO 3266800400 3. CORRECT THE FAN LABEL Checked 01/05’10 Approved Issue Date 01/05’10 Skyler-Huang07/24’13 07/24’13 07/24’13 12/31’15 12/31’15 12/31’15 MATERIAL&CARTON SIZE 4. CHANGE SCREW P/N FROM 3105464700 TO 3534205600 02 Change TIM from TC-1996 to TC-5630 Description: SAMPLE REVISION CODE LIST Part No. REV DELTA MODEL : FHS-A6025B00 Form No.︰tMP—D029 TOTAL 24 PAGE 02 Form Rev.︰00 Delta Electronics Corp. CONTENTS Item Element Description Page 1 Specification 5 2 Print 6 3 Packing Plan 12 4 Fan 15 Form No.︰tMP—D029 Note Form Rev.︰00 Delta Electronics Corp. 1. SPECIFICATION Characters Item Scope Description THIS SPECIFICATION DEFINES THE ELECTRICAL AND MECHANICAL CHARACTERISTICS OF THE FAN HEATSINK INTEL CPU COOLER Application Specification a: Thermal Resistance 0.306 (℃/W) (REF.) 500 g (REF.) b: total weight 16 kgf (REF.) c: clip force BOM Item Part Name 1 FAN 2 HEATSINK 3 Material Part NO. Q’TY PBT 3620936511 1 AL6063 3346423400 1 FAN SCREW SUS 3109183100 2 4 SCREW SUS 3534205600 4 5 LABEL PP OR PET 3266800400 1 6 TIM DOW TC-5630 4021107300 0.2g 7 SPRING SWPA 3461809700 4 8 E-CLIP S20C 3110262800 4 9 CAP SUS303 3462384700 4 Form No.︰tMP—D029 Remark Rev02 Form Rev.︰00 Delta Electronics Corp. 2. PRINT Assembly Drawing Parts Drawing Form No.︰tMP—D029 Form Rev.︰00 Delta Electronics Corp. 3. PACKING PLAN Packing Specification Form No.︰tMP—D029 Form Rev.︰00 Delta Electronics Corp. 4. FAN Fan Specification Form No.︰tMP—D029 Form Rev.︰00 SPECIFICATION FOR APPROVAL Customer _TMPBU____ Description DC FAN Part No. __ 3620936511 REV. ______ Delta Model No. __AFB0612DH-BC01 __ REV. _ 01 Sample Issue No. Sample Issue Date _AUG.13.2012 PLEASE SEND ONE COPY OF THIS SPECIFICAITON BACK AFTER YOU SIGNED APPROVAL FOR PRODUCTION PREARRANGMENT. APPROVED BY: DATE : DELTA ELECTRONICS, INC. TAOYUAN PLANT 252, SHANG YING ROAD, KUEI SAN INDUSTRIAL ZONE TAOYUAN SHIEN, TAIWAN, R.O.C. TEL:886-(0)3-3591968 FAX:886-(0)3-3591991 Application Notice 1. Delta will not guarantee the performance of the products if the application condition falls outside the parameters set forth in the specification. 2. A written request should be submitted to Delta prior to approval if deviation from this specification is required. 3. Please exercise caution when handling fans. Damage may be caused when pressure is applied to the impeller, if the fans are handled by the lead wires, or if the fan was hard-dropped to the production floor. 4. Except as pertains to some special designs, there is no guarantee that the products will be free from any such safety problems or failures as caused by the introduction of powder, droplets of water or encroachment of insect into the hub. 5. The above-mentioned conditions are representative of some unique examples and viewed as the first point of reference prior to all other information. 6. It is very important to establish the correct polarity before connecting the fan to the power source. Positive (+) and Negative (-). Damage may be caused to the fans if connection is with reverse polarity, if there is no foolproof method to protect against such error specifically mentioned in this spec. 7. Delta fans without special protection are not suitable where any corrosive fluids are introduced to their environment. 8. Please ensure all fans are stored according to the storage temperature limits specified. Do not store fans in a high humidity environment. We highly recommend performance testing is conducted before shipping, if the fans have been stored over 6 months. 9. Not all fans are provided with the Lock Rotor Protection feature. If you impair the rotation of the impeller for the fans that do not have this function, the performance of those fans will lead to failure. 10. Please be cautious when mounting the fan. Incorrect mounting of fans may cause excess resonance, vibration and subsequent noise. 11. It is important to consider safety when testing the fans. A suitable fan guard should be fitted to the fan to guard against any potential for personal injury. 12. Except where specifically stated, all tests are carried out at room (ambient) temperature and relative humidity conditions of 25oC, 65% RH. The test value is only for fan performance itself. 13. Be certain to connect an “ 4.7µF or greater” capacitor to the fan externally when the application calls for using multiple fans in parallel, to avoid any unstable power. Doc. No: FMBG-ES Form 001 Rev. 0001 Date: June 24, 2009