FHS-A6025B02A

Delta Electronics Corp. APPROVAL SHEET Customer Name .: STD Model Name.: Heatsink Delta Part No.: FHS-A6025B02A Customer Part No.: Spec Issue Date .: Spec Revision : --12/31/2015 01 PLEASE SEND ONE COPY OF THIS SPECIFICATION BACK AFTER YOU SIGNED APPROVAL FOR PRODUCTION PRE-ARRANGMENT. Approved By: Date: Approval Form No.︰tMP—D029 Check Designer Form Rev.︰00 Delta Electronics Corp. REV. 00 01 Description Drawn Checked Approved 8/15’12 8/15’12 8/15’12 12/31’15 12/31’15 12/31’15 Issue Date ISSUE SPEC Change TIM from TC-1996 to TC-5630 Description: SAMPLE REVISION CODE LIST Part No. REV DELTA MODEL : FHS-A6025B02A Form No.︰tMP—D029 TOTAL 22 PAGE Form Rev.︰00 01 Delta Electronics Corp. CONTENTS Item Element Description Page 1 Specification 4 2 Print 5 3 Packing Plan 9 4 Fan 12 Form No.ΝtMP—D029 Note Form Rev.Ν00 Delta Electronics Corp. 1. SPECIFICATION 1.1 Characters Item Description THIS SPECIFICATION DEFINES THE ELECTRICAL AND Scope MECHANICAL CHARACTERISTICS OF THE FAN HEATSINK Application Specification a: Thermal Resistance b: total weight c: clip force 1.2 INTEL LGA2011 CPU HEATSINK 0.18 (°C/W)(REF.) 535 g (REF.) 29.5 Kgf (REF.) BOM Item Part Name 1 FAN 2 Material Part NO. Q’TY PBT 3620936511 1PCE FAN SCREW SUS 302 3109182300 2PCE 3 FAN LABEL POLYESTER 3267299800 1PCE 4 FIN A1050 / C1100 3346397100 1PCE 5 AL BASE ADC12 3346814700 1PCE 6 CU BASE CU 1100 3346397300 1PCE 7 HEATPIPE CU 1020 3460037000/ 4PCE Remark 3460037600~3460037800 8 SOLDER SN / BI 4090207800 14.5 g 9 SCREW SUS 304 3105359900 4PCE 10 SPRING ASTM A228 3462028800 4PCE 11 E CLIP SK7 3110264700 4PCE 12 SPACER POM 3244747000 4PCE 13 COVER ABS 3321044300 1PCE 14 GREASE TC-5630 4021107300 0.2 g 15 BOX LABEL PAPER 3261447400 0.031PCE 16 TRAY PET 3503125200 1PCE 17 BOX PAPER 3518141900 1PCE 18 PAD PAPER PAPER 3516275100 0.125PCE 19 CARTON PAPER 3513743100 0.042PCE Form No.︰tMP—D029 Rev01 Form Rev.︰00 Delta Electronics Corp. 2. PRINT 2.1 Assembly Drawing Form No.ΝtMP—D029 Form Rev.Ν00 Delta Electronics Corp. 3. Packing Plan Form No.ΝtMP—D029 Form Rev.Ν00 Delta Electronics Corp. 4. FAN 4.1 Fan Specification Form No.ΝtMP—D029 Form Rev.Ν00 SPECIFICATION FOR APPROVAL Customer _TMPBU____ Description DC FAN Part No. __ 3620936511 REV. ______ Delta Model No. __AFB0612DH-BC01 __ REV. _ 01 Sample Issue No. Sample Issue Date _AUG.13.2012 PLEASE SEND ONE COPY OF THIS SPECIFICAITON BACK AFTER YOU SIGNED APPROVAL FOR PRODUCTION PREARRANGMENT. APPROVED BY: DATE : DELTA ELECTRONICS, INC. TAOYUAN PLANT 252, SHANG YING ROAD, KUEI SAN INDUSTRIAL ZONE TAOYUAN SHIEN, TAIWAN, R.O.C. TEL:886-(0)3-3591968 FAX:886-(0)3-3591991 Application Notice 1. Delta will not guarantee the performance of the products if the application condition falls outside the parameters set forth in the specification. 2. A written request should be submitted to Delta prior to approval if deviation from this specification is required. 3. Please exercise caution when handling fans. Damage may be caused when pressure is applied to the impeller, if the fans are handled by the lead wires, or if the fan was hard-dropped to the production floor. 4. Except as pertains to some special designs, there is no guarantee that the products will be free from any such safety problems or failures as caused by the introduction of powder, droplets of water or encroachment of insect into the hub. 5. The above-mentioned conditions are representative of some unique examples and viewed as the first point of reference prior to all other information. 6. It is very important to establish the correct polarity before connecting the fan to the power source. Positive (+) and Negative (-). Damage may be caused to the fans if connection is with reverse polarity, if there is no foolproof method to protect against such error specifically mentioned in this spec. 7. Delta fans without special protection are not suitable where any corrosive fluids are introduced to their environment. 8. Please ensure all fans are stored according to the storage temperature limits specified. Do not store fans in a high humidity environment. We highly recommend performance testing is conducted before shipping, if the fans have been stored over 6 months. 9. Not all fans are provided with the Lock Rotor Protection feature. If you impair the rotation of the impeller for the fans that do not have this function, the performance of those fans will lead to failure. 10. Please be cautious when mounting the fan. Incorrect mounting of fans may cause excess resonance, vibration and subsequent noise. 11. It is important to consider safety when testing the fans. A suitable fan guard should be fitted to the fan to guard against any potential for personal injury. 12. Except where specifically stated, all tests are carried out at room (ambient) temperature and relative humidity conditions of 25oC, 65% RH. The test value is only for fan performance itself. 13. Be certain to connect an “ 4.7µF or greater” capacitor to the fan externally when the application calls for using multiple fans in parallel, to avoid any unstable power. Doc. No: FMBG-ES Form 001 Rev. 0001 Date: June 24, 2009