GTW020EUB12

SPECIFICATION FOR APPROVAL Customer _____ Description __ __GT FAN __ REV. Part No. Delta Model No. __GTW020EUB12 __ ______ REV. _02_ Sample Issue No. Sample Issue Date ____Apr.26 2 0 1 3 PLEASE SEND ONE COPY OF THIS SPECIFICAITON BACK AFTER YOU SIGNED APPROVAL FOR PRODUCTION PREARRANGMENT. APPROVED BY: DATE : DELTA ELECTRONICS, INC. TAOYUAN PLANT 252, SHANG YING ROAD, KUEI SAN INDUSTRIAL ZONE TAOYUAN SHIEN, TAIWAN, R.O.C. TEL:886-(0)3-3591968 FAX:886-(0)3-3591991 Application Notice 1. DELTA WILL NOT GUARANTEE THE PERFORMANCE OF THE PRODUCTS IF THE APPLICATION CONDITION FALLS OUTSIDE THE PARAMETERS SET FORTH IN THE SPECIFICATION. 2. A WRITTEN REQUEST SHOULD BE SUBMITTED TO DELTA PRIOR TO APPROVAL IF DEVIATION FROM THIS SPECIFICATION IS REQUIRED. 3. PLEASE EXERCISE CAUTION WHEN HANDLING FANS. DAMAGE MAY BE CAUSED WHEN PRESSURE IS APPLIED TO THE IMPELLER, IF THE FANS ARE HANDLED BY THE LEAD WIRES, OR IF THE FAN WAS HARD-DROPPED TO THE PRODUCTION FLOOR. 4. EXCEPT AS PERTAINS TO SOME SPECIAL DESIGNS, THERE IS NO GUARANTEE THAT THE PRODUCTS WILL BE FREE FROM ANY SUCH SAFETY PROBLEMS OR FAILURES AS CAUSED BY THE INTRODUCTION OF POWDER, DROPLETS OF WATER OR ENCROACHMENT OF INSECT INTO THE HUB. 5. THE ABOVE-MENTIONED CONDITIONS ARE REPRESENTATIVE OF SOME UNIQUE EXAMPLES AND VIEWED AS THE FIRST POINT OF REFERENCE PRIOR TO ALL OTHER INFORMATION. 6. DELTA FANS WITHOUT SPECIAL PROTECTION ARE NOT SUITABLE WHERE ANY CORROSIVE FLUIDS ARE INTRODUCED TO THEIR ENVIRONMENT. 7. PLEASE ENSURE ALL FANS ARE STORED ACCORDING TO THE STORAGE TEMPERATURE LIMITS SPECIFIED. DO NOT STORE FANS IN A HIGH HUMIDITY ENVIRONMENT. WE HIGHLY RECOMMEND PERFORMANCE TESTING IS CONDUCTED BEFORE SHIPPING, IF THE FANS HAVE BEEN STORED OVER 6 MONTHS. 8. PLEASE BE CAUTIOUS WHEN MOUNTING THE FAN. INCORRECT MOUNTING OF FANS MAY CAUSE EXCESS RESONANCE, VIBRATION AND SUBSEQUENT NOISE. 9. EXCEPT WHERE SPECIFICALLY STATED, ALL TESTS ARE CARRIED OUT AT ROOM (AMBIENT) TEMPERATURE AND RELATIVE HUMIDITY CONDITIONS OF 25OC, 65% RH. THE TEST VALUE IS ONLY FOR FAN PERFORMANCE ITSELF. 10. THIS AC FAN SHALL COMPLY WITH THE END-PRODUCT STANDARD AFTER INSTALLATION. 11. THIS AC FAN IS DESIGNED IN ORDER TO ASSEMBLE IT WITHIN AN END-USE PRODUCT.DO NOT USE IT INDEPENDENTLY BEFORE INSTALLATION TO AVOID A HAZARD. 12. A FAN GUARD SHALL BE PROVIDED TO AVOID HAZARDS IF THE AC FAN MAY BE ACCESSIBLE BY USERS AFTER INSTALLATION. 13. THE AC FAN SHALL BE SECURE FIXED WITHIN AN END-PRODUCT. 14. DAMAGE TO THE AC FAN AND THE END-PRODUCT MIGHT OCCUR IF INCORRECT INSTALLED. 15. THE METAL FRAME OF THE AC FAN SHALL BE EARTHED AN EARTHING CONDUCTOR SHALL NOT BE LESS THAN 18AWG(0.75mm2). 16. A SPRING OR STAR-WASHER SHALL BE USED TOGETHER WITH EARTHING SCREW FOR CONNECTION . 17. THE AC FAN SHALL BE NOT CONNECTED TO MAINS SUPPLY DURING INSTALLATION. 18. THE AC FAN DISTANCE TO OTHER COMPONENT SHALL BE KEEP 25mm. 19. THE AC FAN SHALL BE USE ONLY THE INCLUDED METAL SCREWS AND NUTS FOR FIXING. 20. THE AC FAN FOR APPLIANCES WITH TYPE Z ATTACHMENT.THE SUPPLY CORD CAN NOT BE REPLACED.IF THE CORD IS DAMAGED THE APPLIANCE SHOULD BE SCRAPPED. 21. THE ROTATING IMPELLER MUST BE GUARDED.AND FAN GUARD SHALL COMPLY WITH THE RELEVANT END-PRODUCT. Doc. No: FMBG-ES Form 001 Rev.GT01 Date: April 25, 2013