PFR05S-103-JNH

CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH REVISION : A3 PAGE : 1 OF 9 1/16W, 0402, High Precision Thick Film Chip Resistor (Lead / Halogen Free) 1. Scope This specification applies to 1.0mm x 0.5mm ( 0402 ) size, fixed metal chip resistors rectangular type for use in electronic equipment. 2. Type Designation PFR05 X — XXXX — X NH (1) (2) (3) (4) (5) Where (1) Series No. (2) Tolerance of TCR : X = Jumper Resistor refer to paragraph 3 (3) Nominal resistance value : For example –Three digits of number (E-24 Series) 000 = Jumper（0） 100 = 10 102 = 1k Four digits of number (E-96 Series) 11R3 = 11.3 1131 =1.13k (4) Resistance tolerance : X = Jumper(Below 50m) D =  0.5% F =  1.0% J =  5.0% (5) NH = Sn plating ( Lead free / Halogen free) CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH REVISION : A3 PAGE : 2 OF 9 3. Electrical Specifications Table 1. : Power Rating** Resistance Values Resistance Range (  ) Temperature Coefficient of Resistance ppm/℃ (code) * 10 ~ 97.6 100 (R) 100 ~ 1M 50 (Q) 1K~1.8M 1.0 ~ 9.76 10 ~ 97.6 1.02M ~ 10M 100 ~ 1M 10 ~ 10M 1.0 ~ 9.1 10 ~ 10M 25 (P) Resistance Tolerance 0.5%(D) 1/16 W E-24 series E-96 series 1.0%(F) E-24 series 5.0%(J) 0 ~ 500 (S) 100 (R) Operating Temperature Range Max. Operating Voltage*** -55℃ to +125℃ 50V 50 (Q) 200 (S) 0 ~ 500 (S) 200 (S) Note: *TCR “S” is standard parts, the other part can be make at request. Note: **Package Power Temperature Derating Curve RATED LOAD(%) 100 0 -55 70 125 AMBIENT TEMPERATURE(℃) Figure 1.：Power Temperature Derating Curve Note: ***esistors shall have a rated DC or AC(rms.) continuous operating voltage corresponding to the power rating, as calculated from the following formula Where V : Rated voltage (V) V  PR P : Rated power (W) R : Nominal resistance () If the voltage so obtained exceeds the maximum operating voltage, this maximum voltage shall be the rated voltage. Table 2. : Jumper: Resistance Tolerance Below 50 mΩ Rated current 1A Operating Temperature Range -55℃ to 125℃ CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH REVISION : A3 PAGE : 3 OF 9 4. Outline dimensions L a a W Code Letter Dimension L 1.0  0.05 W 0.50  0.05 t 0.35  0.05 a 0.2  0.10 t Unit : mm 5. Life Tests 5-1 Electrical Specification and Requirement Test Method (Refer to JIS C 5201) Item Resistor Jumper  100ppm Max. 50m △R:  (1%+ 0.05)  TCR  100ppm △R:  (2%+ 0.1) Without damage by flashover, spark, arcing, burning or breakdown Insulation Resistance Over 100 M on Overcoat layer face up Over 1,000 M on Substrate side face up Short Time Overload Voltage Proof  TCR △R:  (2%+ 0.1) Without damage by flashover, spark, arcing, burning or breakdown Max. 50m Pressure Rod (Metal) (1) Applied voltage : 2.5 x rated voltage or 2 x maximum operating voltage which ever is less (2) Test time : 5 seconds (1) Setup as figure 2 (2) Test voltage : 50VDC (3) Test time : 60 + 10 / -0 seconds (1) Setup as figure 2 (2) Test voltage : 100VAC(rms.) (3) Test time : 60 +10 / -0 seconds Insulation Plate Measurement Point (R=0.5 mm) A Substrate A Over coat Film B Spring Sample Electrode Voltage Supply Metal Block Measurement Point B Substrate Side Figure 2 : Measurement Setup CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH REVISION : A3 PAGE : 4 OF 9 5-2 Mechanical Specification and Requirement Item Resistor Solderability Jumper Test Method (Refer to JIS C 5201) The surface of terminal immersed shall be Solder bath : minimum of 95% covered with a new After immersing in flux, dip in coating of solder 245  5℃ molten solder bath for 2  0.5 seconds Resistance to Solder △R:  (1.0%+ 0.05) Heat Without distinct deformation in appearance Max. 50m (1) Pre-heat: 100~110℃ for 30 seconds (2) Immersed at solder bath of 270  5℃ for 10  1 seconds (3) Measuring resistance 1 hour after test Vibration (1) Vibration frequency : △R:  (0.5%+ 0.05) 10Hz to 55Hz to10Hz in 60 Without mechanical damage such as break seconds as a period (2) Vibration time : period cycled for 2 hours in each of 3 mutual perpendicular directions (3) Amplitude : 1.5mm Shock (1) Peak value : 490N △R:  (0.25%+ 0.05) Without mechanical damage such as break (2) Duration of pulse : 11ms (3) 3 times in each positive and negative direction of 3 mutual perpendicular directions Bending Test △R:  (1.0%+ 0.05) Without mechanical damage such as break Max. 50m Bending value : 3 mm for 30  1 seconds CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH REVISION : A3 PAGE : 5 OF 9 5-3 Endurance Specification and Requirement Item Resistor Thermal Shock Jumper Max. 50m △R:  (1.0%+ 0.05) Without distinct damage in appearance Moisture with Load △R:  (5.0%+ 0.1) Max. 50m Without distinct damage in appearance Marking should be legible Load Life △R:  (5.0%+ 0.1) Without distinct damage in appearance Max. 100m Low Temperature Store △R:  (5.0%+ 0.1) Without distinct damage in appearance Max. 100m High Temperature Store △R:  (5.0%+ 0.1) Without distinct damage in appearance Max. 100m Test Method (Refer to JIS C 5201) (1) Repeat 5 cycle as follows : (-55  3℃,30minutes) (Room temperature, 2~3 minutes) (+125  2℃,30minutes) (Room temperature, 2~3 minutes) (2) Measuring resistance 1 hour after test (1) Environment condition : 40  2℃,90~95% RH (4) Applied Voltage: rated voltage (2) Test period: (1.5 hour ON (0.5 hour OFF) cycled for total 1,000 + 48 / - 0 hours (3) Measuring resistance 1 hour after test (1) Test temperature : 70  2℃ (2) Applied Voltage: rated voltage (3) Test period : (1.5 hour ON) (0.5 hour OFF) cycled for total 1,000 + 48 / - 0 hours (4) Measuring resistance 1 hour after test (1) Store temperature : -55  3℃ for total 1,000 + 48 / - 0 hours (2) Measuring resistance 1 hour after test (1) Store temperature : +125  2℃ for total 1,000 + 48 / - 0 hours (2) Measuring resistance 1 hour after test CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH REVISION : A3 PAGE : 6 OF 9 6. Recommend Land Pattern Dimensions A B C A 0.5 B 1.5 C 0.4~0.8 Unit : mm CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH REVISION : A3 PAGE : 7 OF 9 7. Packaging 7-1 Dimensions 7-1-1 Tape packaging dimensions +- 1.5 0.43 ± 0.05 0.1 0.0 Sprocket hole 4.0 ± 0.1 3.5 ± 0.05 A Chip 1.75 ±0.1 8.0 ± 0.3 B 0.50 ± 0.1 A = 0.65 ± 0.10 B = 1.15 ± 0.10 Carrier cavity 2.0 ± 0.05 Pull Direction Unit : mm 7-1-2 Reel dimensions 2.0±0.5 60 ± 2.0 178 ± 2.0 13 ± 0.2 21 ± 0.8 9.0 ± 0.3 Unit : mm 11.4 ± 1.0 CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH 7-2 Peel force of top cover tape The peel speed shall be about 300 mm/minute The peel force of top cover tape shall be between 0.1 to 0.7 N Top Cover Tape 165 ~ 180° 0.1~0.7 N 7-3 Numbers of taping 10,000 pieces/reel 7-4 Label marking The following items shall be marked on the production and shipping Label on the reel. 7-4-1 Production Label (1) Part No. (2) Description (3) Quantity (4) Taping No. 7-4-2 Shipping Label (1) *Customer's name (2) *Customer's part No. (3) Manufacturer's part No. (4) Manufacturer's name (5) Manufacturer's country *Note : Item (1) and (2) are listed by request REVISION : A3 PAGE : 8 OF 9 CYNTEC CO., LTD. 乾坤科技股份有限公司 DOCUMENT : RH000000NH REVISION : A3 PAGE : 9 OF 9 8. Care note 8-1 Care note for storage (1) Chip resistor shall be stored in a room where temperature and humidity must be controlled. (temperature 5 to 35℃, humidity 45 to 85% RH) However, a humidity keep it low, as it is possible. (2) Chip resistor shall be stored as direct sunshine doesn’t hit on it. (3) Chip resistor shall be stored with no moisture, dust, a material that will make solderability inferior, and a harmful gas (Chloridation hydrogen, sulfurous acid gas, and sulfuration hydrogen) 8-2 Care note for operating and handling (1) It is necessary to protect the edge and protection coat of resistors from mechanical stress. (2) Handle with care when printing circuit board (PCB) is divided or fixed on support body, (3) (4) (5) (6) because bending of printing circuit board (PCB) mounting will make mechanical stress for resistors. Resistors shall be used with in rated range shown in specification. Especially, if voltage more than specified value will be loaded to resistor, there is a case it will make damage for machine because of temperature rise depending on generating of heat, and increase resistance value or breaks. In case that resistor is loaded a rated voltage, it is necessary to confirms temperature of a resistor and to reduce a load power according to load reduction curve, because a temperature rise of a resistor depends on influence of heat from mounting density and neighboring element. Observe Limiting element voltage and maximum overload voltage specified in each specification If there is possibility that a large voltage (pulse voltage, shock voltage) charge to resistor, it is necessary that operating condition shall be set up before use.