3mm LED CBI® Circuit Board Indicator Bi-level
PART NO.
4.32 [.170] CATHODE ID 8.13 [.320]
553-xxxx
COLOR* Red Green Yellow Orange Blue³ Red Green Yellow Red Green Yellow Red/Green Yellow/Green Red Green Yellow
HIGH EFFICIENCY - LED TYPE 01
9.65 [.380]
5.08 [.200] 2.54 [.100]
553-0111 553-0122 553-0133 553-0177 553-0188
.508 SQ. [.020] 2.54 [.100] 4.44 [.175] Top LED
NEW
3.68 [.145]
RECOMMENDED P.C. BOARD LAYOUT .254 [.100]
CATHODE 2.6 Red/Yel [.102] Cathode for MAX Bicolor 1.0 [.040]
LOW CURRENT - LED TYPE 02
553-0211 553-0222 553-0233
RESISTOR 5 VOLTS - LED TYPE 03
Dimensions in mm [inches]
Standard Polarity shown in drawing: Cathode right
Features
• Multiple CBIs form horizontal LED arrays on 4.45mm (0.175”) center-lines. See page 4-41 and 4-42 for pre-assembled arrays • High Contrast, UL 94 V-0 rated, black housing • Oxygen index: 32% • Polymer content: PBT, 0.343 g • Housing stand-offs facilitate PCB cleaning • Solderability per MIL-STD-202F, method 208F • LEDs are safe for direct viewing per IEC 825-1, EN-60825-1
553-0311 553-0322 553-0333
BI-COLOR - LED TYPE 07
553-0711 553-0744
NON-DIFFUSED - LED TYPE 22
553-2211 553-2222 553-2233 * Top-Bottom LED
Tolerance note: As noted, otherwise:
• LED Protrusion: ±0.04 mm [±0.016] • CBI Housing: ±0.02mm[±0.008]
To order any of the 553-xxxx part numbers with Reverse Polarity (Cathode Left), please add -010 to the part numbers shown above.
Custom Combinations
• Contact factory for information on custom bi-level arrays and color combinations.
PART NUMBER ORDERING CODE
553– xxxx –010
Series LED Type Top Position Color Bottom Position Color
Color = 0) Blank 1) Red or Red/Green Bi-Color 2) Green 3) Yellow 4) Yellow/Green Bi-Color 7) Orange 8) Blue
³
ATTENTION
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES
Reverse Polarity Option 1) Cathode Left
–010 Ordering Code Suffix required ONLY for Reverse Polarity Option
4-28 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
553-xxxx
Typical Operating Characteristics (TA=25°C)
HIGH EFFICIENCY Part Number 553-0111 553-0122 553-0133 553-0177 553-0188 LOW CURRENT Part Number 553-0211 553-0222 553-0233 Color Red Green Yellow Orange Blue Peak Wavelength nm 650 563 585 600 428 Peak Wavelength nm 635 565 585 IV mcd 10 16 6.3 7 12 IV mcd 1.6 1.6 1.6 VF Volts 2 2.1 2.1 2.2 3.5 VF Volts 1.7 1.9 1.8 Test Current (mA) 10 10 10 10 10 Test Current (mA) 2 2 2 Viewing Angle 2 Θ½ 45° 45° 45° 60° 70° Viewing Angle 2 Θ½ 60° 60° 60° LED Data sheet 521-9427 521-9408 521-9428 521-9498 521-9831 LED Data sheet 521-9324 521-9326 521-9325 Page # 4-64 4-64 4-64 4-58 4-57
See LED data sheet for additional information See page 4-70 and 4-71 for Reference Only LED Drive Circuit Examples. See page 4-72 for Pin Out
Color Red Green Yellow
Page # 4-60 4-60 4-60
INTEGRAL RESISTOR, 5 VOLTS Part Number 553-0311 553-0322 553-0333 BI-COLOR Part Number 553-0711 553-0744
* IF = 20mA
Color Red Green Yellow
Peak Wavelength nm 635 565 585
IV mcd 29 19 12.6
Test Voltage 5 5 5
Forward Current (mA) 10 10 10
Viewing Angle 2 Θ½ 60° 60° 60°
LED Data sheet 521-9215 521-9323 521-9322
Page # 4-59 4-59 4-59
4
Color Red/Green Yellow/Green
Peak Wavelength nm 635/565 585/565
IV mcd 4.7/10 4.3/6.3
VF Volts 2/2.1 2.1*/2.1*
Test Current (mA) 10 10
Viewing Angle 2 Θ½ 50° 80°
LED Data sheet 521-9459 521-9478
Page # 4-63 4-62
NON-DIFFUSED Part Number 553-2211 553-2222 553-2233
* IF = 20mA
Color Red Green Yellow
Peak Wavelength nm 635 565 585
IV mcd 29 50 20
VF Volts* 2 2.1 2.1
Test Current (mA) 10 10 10
Viewing Angle 2 Θ½ 45° 45° 45°
LED Data sheet 521-9432 521-9430 521-9431
Page # 4-61 4-61 4-61
CBI ARRAYS .200 PITCH
Dialight offers its Multiarray to reduce insertions and to assure indicator alignment. Multiarrays mount indicators on .200 centers. These assemblies are available in arrays of 2 to 6. See pages 4-41 and 4-42 for information. Call factory for information on .185 pitched arrays.
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
4-29
NEW
3mm Discrete LED Tinted, Diffused
521-9831
PART NO.
SURFACE NOT FLAT 4.8 [.189] 4.4 [.173] 4.8 [.189] 4.4 [.173] 0.7 [.028] 0.4 [.016] 0.6 [.024] 0.4 [.016] 2.54 [.100] 3.4 [.134] 3.1 [.122]
521-9831
COLOR Blue³
2.9 [.114] ø 2.7 [.106]
3.7 [.145] 3.5 [.138] 6.1 [.240] 5.7 [.224]
CATHODE
1.8 [.071] 1.2 [.047]
0.6 [.024] 0.4 [.016]
29 [1.142] 27 [1.063]
Dimensions in mm [inches]
MOUNTING CLIP: 515-0006 located on page 4-65
³
ATTENTION
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES
4
Blue
ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) From 55°C Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature
Solder Adherence per MIL-STD-202E, Method 208C
-9831 100 20 .44 -40/+100 -40/+100 260°C, 5 seconds, 1.6 mm from case
Blue
OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=10mA Peak Wavelength (nm) λ Peak Viewing Angle (2Θ½) Forward Voltage (V) IF=10mA Reverse Voltage (V) IR=10µA
-9831 Min. Typical Typical Typical Typical Max. Min. 6.3 12 428 70° 3.5 4.2 3
Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
4-57
3mm Discrete LED High Efficiency Diffused 521-9210,
-9211, -9216, -9498, -9636
PART NO. COLOR 521-9210 Green 521-9211 Yellow 521-9216 Red 521-9498 Orange 521-9636 Red
2.54 [.100]
4.45 [.175] 1.02 [.040]
25.4 [1.0] MIN
1.02 [.040] MIN
3.30 [.13]
NEW
3.00 [.118]
1.50 [.059] MAX 6.00 [.236]
.45 [.016 ]
.40 [.016]
MOUNTING CLIP: 515-0006 located on page 4-65
short lead cathode all colors except 521-9636 Red. For 521-9636 Red, short lead is anode.
Dimensions in mm [inches]
Green
Yellow
Red
Orange
Red
ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) From 50°C Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature
Solder Adherence per MIL-STD-202E, Method 208C
1
-9210 100
-9211 60 20 .25 -55/+100 -55/+100
-9216 100 30 .4 -55/+100 -55/+100
-9498 135 25 .5 -55/+100 -55/+100
-9636 100 40 .51 -55/+100 -55/+100
from 25°C
30 .4 -55/+100 -55/+100
260°C, 5 seconds, 1.6 mm from body
Green
Yellow
Red
Orange
Red
OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=10mA 1 IF=20mA Peak Wavelength (nm) λ Peak Viewing Angle (2Θ ½) Forward Voltage (V) IF=10mA 1 IF=20mA Reverse Voltage (V), IR=100µA Min. Typical Typical Typical Typical Max. Max.
-9210 4.7 12.6 565 60° 2.11 2.81 5
-9211 7.4 10 585 60° 2.11 2.81 5
-9216 7.4 10 635 60° 21 2.81 5
-9498 3.4 7 600 60° 2.2 3 5
-9636 8.71 481 660 60° 1.81 2.41 4
Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity
4-58 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
3mm Discrete LED Integral Resistor, 5V Diffused
4.40 [.175] 1.01 [.040] 1.0 [.040] .457 [.018] SQ.
521-9215, -9322, -9323
PART NO. 521-9215 521-9322 521-9323 COLOR Red Yellow Green
3.20 2.90 [.125] [.115]
2.54 [.100]
5.97 [.235]
2.41 [.950] MAX
1.27 [.050]
CATHODE
Dimensions in mm [inches]
MOUNTING CLIP: 515-0006 located on page 4-65
Red
Yellow
Green
ABSOLUTE MAXIMUM RATINGS (TA=25°C) Forward Voltage (V) Derating (V/°C) From 50°C Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature
Solder Adherence per MIL-STD-202E, Method 208C
-9215 7.5 .086 -40/+85 -55/+100
-9322 7.5 .086 -40/+85 -55/+100
-9323 7.5 .071 -20/+85 -55/+100
4
260°C, 5 seconds, 1.6 mm from case
Red
Yellow
Green
OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) VF=5V Peak Wavelength (nm) λ Peak Viewing Angle (2Θ½) Forward Current (mA) VF=5V Reverse Voltage (V), IR=100µA Min. Typical Typical Typical Typical Max. Min.
-9215 8.7 29 635 60° 10 20 5
-9322 3.7 12.6 585 60° 10 20 5
-9323 5.6 19 565 60° 10 20 5
Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
4-59
3mm Discrete LED Low Current Diffused
4.4 [.175] 1.01 [.040] .40 [.016]
521-9324, -9325, -9326
PART NO. COLOR Red Yellow Green 521-9324 521-9325 521-9326
1.0 [.040]
3.3 [.130] 1.00 26.67 [.040] [1.05] MIN. .40 [.016]
2.54 [.100]
5.97 [.235]
CATHODE
Dimensions in mm [inches]
MOUNTING CLIP: 515-0006 located on page 4-65
Red
Yellow
Green
ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) From 90°C Peak Current (mA)
Pulse width = 10 µs
-9324 20 7 .7 500 -55/+100 -55/+100
-9325 20 7 .7 500 -55/+100 -55/+100
-9326 20 7 .7 500 -55/+100 -55/+100
Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature
Solder Adherence per MIL-STD-202E, Method 208C
260°C, 5 seconds, 1.6 mm from case
Red
Yellow
Green
OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=2mA Peak Wavelength (nm) λ Peak Viewing Angle (2Θ ½) Forward Voltage (V) IF=2mA Reverse Voltage (V), IR=50µA
-9324 Min. Typical Typical Typical Typical Max. Min. 1 1.6 635 60° 1.7 2.2 5
-9325 1 1.6 585 60° 1.8 2.7 5
-9326 1 1.6 565 60° 1.9 2.2 5
Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity
4-60 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
3mm Discrete LED High Efficiency Tinted, Non-Diffused
4.44 [.175] 1.0 [.040] 1.0 [.040] .457 [.018] 3.2 [.126]
521-9430, -9431, -9432
PART NO. 521-9430 521-9431 521-9432
2.54 [.100]
COLOR Green Yellow Red
3.0 [.118] 1.27 [.050] .40 [.016]
5.97 MAX [.235]
25.4 [.100] MIN
CATHODE
Dimensions in mm [inches]
MOUNTING CLIP: 515-0006 located on page 4-65
Green Yellow Red
ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) From 50°C Peak Current (mA)
Pulse width = 100µs
-9430 100 30 .4 120 -55/+100 -55/+100
-9431 60 20 .25 80 -55/+100 -55/+100
-9432 100 30 .4 120 -55/+100 -55/+100
4
Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature
Solder Adherence per MIL-STD-202E, Method 208C
260°C, 5 seconds, 1.6 mm from case
Green
Yellow
Red
OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=10mA Peak Wavelength (nm) λ Peak Viewing Angle (2Θ½) Forward Voltage (V) IF=20mA Min. Typical Typical Typical Typical Max.
-9430 32 50 565 45° 2.1 2.8
-9431 10 20 585 45° 2.1 2.8
-9432 8.7 29 635 45° 2 2.8
Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
4-61
3mm Discrete LED Bi-Color Non-Tinted, Diffused
1.02 [.040] 25.40 [1.00] MIN RED CATHODE 521-9768 YELLOW CATHODE 521-9478 GREEN CATHODE 521-9628 3.20 [.126] MAX
521-9478, -9628, -9768
PART NO. 521-9478 521-9628
2.54 [.100]
COLOR Yellow/Green Red/Green Red/Yellow
3.00 [.118] 4.45 [.175] .50 [.020] TYP 2.54 [.100] NOM
521-9768
5.20 ±.5 [.205 ±.02]
NOTE: MENISCUS MAY EXTEND 1.0MM [.040] DOWN FROM HOUSING Dimensions in mm [inches]
MOUNTING CLIP: 515-0006 located on page 4-65
Yellow/Green
Red/Green
Red/Yellow
ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) From 25°C 1 From 50°C Peak Current (mA)
Pulse width = 10µs
-9478 60/100 20/30 .251/.401 80/120 -55/+100 -55/+100
-9628 140/100 40/30 .5/.4 200/120 -55/+100 -55/+100
-9768 100/60 30/20 .41/.251 120/80 -55/+100 -55/+100
Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature
Solder Adherence per MIL-STD-202E, Method 208C
260°C, 5 seconds, 1.66 mm from case
Yellow/Green
Red/Green
Red/Yellow
OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) Min. IF=10mA * IF=20mA Typical Peak Wavelength (nm) λ Peak Viewing Angle (2Θ ½) Forward Voltage (V) IF=20mA Reverse Voltage (V) IR=100ua Typical Typical Typical Max. Min.
-9478 2.5/2.5 4.3/6.3 585/565 80° 2.1/2.1 2.8/2.8 5
-9628 3.7*/1.1* 12.6*/3.7* 660/565 200° 1.8/2.1 2.4/2.8 5
-9768 1.7*/1.7* 5.6*/5.6* 630/585 80° 2/2.1 2.8/2.8 5
Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity
4-62 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
3mm Discrete LED Bi-Color Non-Tinted, Diffused
4.59 [.181] 4.0 [.158] 3.00 [.118] 1.80 [.071] MAX 26.92 [1.06] MIN 1.0 [.040] CATHODE GREEN .50 [.020] SQ. NOM. 3.40 [.134] MAX
521-9459
PART NO. 521-9459
2.54 [.100]
COLOR Red/Green
6.10 [.240]
Dimensions in mm [inches]
MOUNTING CLIP: 515-0006 located on page 4-65
4
Red/Green
ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) From 25°C Peak Current (mA)
Pulse width = 10µs
-9459 140 45 .6 1000 -55/+100 -55/+100 260°C, 5 seconds, 1.6 mm from case
Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature
Solder Adherence per MIL-STD-202E, Method 208C
Red/Green
OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=10mA Peak Wavelength (nm) λ Peak Viewing Angle (2Θ½) Forward Voltage (V) IF=10mA
-9459 Min. Typical Typical Typical Typical Max. 2.5/3.7 4.7/10 635/565 50° 2/2.1 2.8/2.8
Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
4-63
3mm Discrete LED High Efficiency Diffused
4.70 ±.20 [.185 ±.008] .79 ±.20 [.031 ±.008] 3.09 ±.20 [.122 ±.008] 1.0 [.040] 6.10 ±.38 [.240 ±.015] 1.30 ±.25 [.051 ±.010] 24.00 ±.25 [.945 ±.010] .50 [.020] NOM 3.30 [.130] MAX
521-94xx
TYPE 521-9408 521-9427 521-9428
2.49 ±.25 [.098 ±.010]
.50 [.020] NOM
COLOR Green Red Yellow
CATHODE (–)
Dimensions in mm [inches]
MOUNTING CLIP: 515-0006 located on page 4-65
Green Red Yellow
ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) Peak Current (mA) Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature
Solder Adherence per MIL-STD-202E, Method 208C From 50°C
-9408 75 25 .5 60 -25/+85 -30/+100
-9427 60 20 .5 60 -25/+85 -30/+100
-9428 60 20 .5 60 -25/+85 -30/+100
260°C, 5 seconds, 1.6 mm from case
Green
Red
Yellow
OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=10mA Peak Wavelength (nm) λ Peak Viewing Angle (2Θ ½) Forward Voltage (V) IF=10mA Reverse Voltage (V), IR=10µA Min. Typical Typical Typical Typical Max. Min.
-9408 5.6 16 563 45° 2.1 3 3
-9427 3.6 10 650 45° 2 3 3
-9428 2.2 6.3 585 45° 2.1 3 3
Θ is the off axis angle at which the luminous intensity is half the axial luminous intensity
4-64 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com