597-3111-1XX

3 x 5mm Rectangular ® Optopipe® Optical Light Pipe, 2 Array (RJ45 Jack) 19.05 [.750] 13.98 [.550] 2.54 [.100] FRONT P ANE L 5.08 [.200] 2 PLCS DIFFUSED FRONT SURF CE A 31.24 [1.23] 515-1070 29.0 [1.142] 3.05 [.120] 1.91 [.075] Recommended MicroLED SMT LEDs for use with 515-1070 PART NO. 3.93 [.155] 20.57 [.81] 3.56 [.140] COLOR Red AlGaAs Red AlGaAs Red Orange Orange Green Green Yellow Yellow Red/Green Red/Green Yellow/Green Yellow/Green Red/Yellow PAGE # 1-19 1-19 1-30 1-19 1-30 1-19 1-30 1-19 1-30 1-20 1-31 1-20 1-31 1-20 3.66 [.144] C.L. LED S 27.94 [1.100] 35.26 [1.388] .71 [.028] 1.50 [.059] .99 [.039] .99 [.039] DIRECTIO N OF LIGHT 27.43 [1.080] C.L. MOUNTIN G PIN #1 7.62 ±.15 [.300 ±.006] 1.57 [.062] 1.57 [.062] 2.01 [.079] 2X Ø 2.87 ±.05 [.113 ±.002] 6.99 [.275] 1.35 [.053] 13.98 [.550] 27.94 ±.05 [1.100 ±.002] NOTE: designed for post-reflow PC board insertion. RECOMMENDED SOLDP D/HOLES LA ER A YOUT FOR BI-COLOR LED S Dimensions in mm [inches] Features • Complements Dialight’s 515-1022 Four Array Optopipe Light Pipe • Allows indicators to be positioned above corresponding RJ45 jack or D-Subminiature • High transmissivity polycarbonate material • UL94V-0 compliance • ESD protection (circuit isolation from front panel) • Wide viewing angle • Arrays reduce insertion costs • Secures to PCB by press-fit 597-3001-1xx 597-3111-1xx 597-3111-5xx 597-3211-1xx 597-3211-5xx 597-3301-1xx 597-3301-5xx 597-3401-1xx 597-3401-5xx 597-7701-1xx 597-7701-5xx 597-7721-1xx 597-7721-5xx 597-7731-1xx LED Data For absolute maximum ratings and other electrical and optical data on the recommended LEDs, refer to LED data sheets. Operating/Storage Temperature –30°C to +100°C Dialight Optopipe® Light Pipe Description This light pipe’s two 3 x 5mm rectangular light emitting surfaces appear bright and are optically well isolated. The light pipe is reliably held in place by 2 press-fit pins located at either end of the light pipe array. This Optopipe® functions as a through-the-case indicator by conducting the light over the top of connectors or switches. A textured finish on the 2 light emitting surfaces maximizes the viewing angle. The recommended light sources are Dialight's 597 Series PLCC-2 or PLCC-4 Type SMT LEDs. The LEDs are mounted in a straight line on an 0.550" pitch. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index. Dialight can provide custom Optopipe® solutions for your applications. Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com