LML6-C1-WW-SP

FEATURES / BENEFITS p Fully modular linear arrays of ultra high brightness LEDs LINEAR MODULES PWM SERIES p Utilizes the latest 100+ lumen LUXEON® Rebel™ LEDs for cool white, 100+ lumen for neutral white & 50+ lumen for warm white p Choice of colour temperatures & optical patterns p >70% lumen maintenance @ 60,000 hours at max acceptable ambient temperature p ETL recognized RECOGNIZED COMPONENT p Lifesaver® thermal protection p Primary heatsinking included OPERATING CONDITIONS p Operating ambient temperature -30ºC to +55ºC (@350mA) p Requires constant current driver p Compatible drivers include Dialight Lumidrives PWD60-35-70 Runs 3-8 modules @ 350mA, 2-4 modules @700mA p Additional heatsinking required when driven @ 700mA APPLICATION p Linear lighting p Accent lighting p Flood lighting p Street & area lighting p General illumination ORDERING INFORMATION MATERIALS / FINISH p Six premium flux LUXEON Rebel LEDs per module p Annodized cast aluminum heatsink p Polycarbonate cover p Dialight-Lumidrives optics (OPC 11 Series) p Modular quick connect cables p Module to module connector cable included Typical Colour (AA) Temperature CW = 5000K - 6350K NW = 3800K - 4100K WW = 2850K - 3250K Optic (BB) SP = 5 degree spot MD = 8 degree med. WD = 20 degree wide OV = 5X25 degree oval FR = 7 degree frosted spot Connectors (sold seperately) LML6-CON-CAB = Entry cable, driver to 1st module LML6-TER-CAB = End plug (required) * Cables use 0.5mm2 AWG12 wires www.dialight.com MECHANICAL DIMENSIONS 11.7” x 1.498” x 0.585” (297.18mm x 38.05mm x 14.86mm) Mounting hole spacing = 3.22” (81.8mm) Max screw size #8 Total length for “Z” units connected end to end = (Z x 11.7) - ((Z-1) x 0.25) (inches) (Z x 297.2) - ((Z-1) x 6.35) (mm) Side View Top View Example: 2 units total length = 23.15” (588.01) Dimensions in mm ASSEMBLY INFORMATION 1) Position ‘tab’ end of first powerwhite module by input wires/driver. (Do not connect power to entry cable before completing steps 2-6) 2) Remove cover from module (Do not remove mask). Modules may be screwed down onto surface by inserting two M6 or 8/32 flathead screws through screw holes. 3) Insert 6 pin prong from LML6-CON-CAB entry cable into 6 prong receptacle near tab end of first module. 4) Insert 4 pin prong from connector cable into ‘notch’ end of module, insert 6 pin prong from connector cable into ‘tab’ end of next module (repeat for each additional module). 5) Connector cable wires can be routed through interior of modules by placing them into interior wire holders. INPUT WIRE CHART Colour wire on A50-LML6-CON-CAB entry cable White 1 White 2 Red Black Green To. Thermistor Thermistor Driver + Driver Ground or Connect to on PWD60-35-70 Wire 5 Wire 6 Wire 2 350mA Wires 1 & 2 700mA Wire 3 Green / Yellow Stripe 6) Insert LML6-TER-CAB 4-pin terminal prong into ‘notch’ end of last module in run (required). 7) Replace covers and connect power to LM60-CON-CAB PHOTOMETRIC DATA TBD IES 32 files available, consult factory Dialight reserves the right to make changes at any time in order to supply the best product possible. The most current version of this document will always be available at: www.dialight.com/Assets\Brochures_And_Catalogs\Illumination\MDEXLUMPWM.pdf MDEXLUMPWM_B www.dialight.com 2