AH173-PG-B-A

AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE Description AH173 is a single-digital-output Hall-Effect latch sensor with pull-up resistor for high temperature operation. The device includes an on-chip Hall voltage generator for magnetic sensing, an amplifier to amplify Hall voltage, a comparator to provide switching hysteresis for noise rejection, and an output driver with a pull-up resistor (Rpu). An internal bandgap regulator provides a temperature compensated supply voltage for internal circuits and allows a wide operating supply range. When the magnetic flux density (B) is larger than operate point (Bop), output is switched on (OUT pin is pulled low). The output state is held on until a magnetic flux density reversal falls below Brp. When B is less than Brp, the output is switched off. The AH173 is available in SIP-3L and SC59 packages. Pin Assignments (Top View) 3. OUT 2. GND 1. Vcc SIP-3L (Top View) 3. OUT GND 2. 1. Vcc SC59 Features • • • • • • • Bipolar Hall-Effect latch sensor 3V to 20V DC operating voltage Built-in pull-up resistor 25mA output sink current Operating temperature: -40°C to +125°C SIP-3L and SC59 packages (SC59 is commonly known as SOT23 in Asia) Green Molding Compound (No Br, Sb) (Note 1) Applications • • • • Rotor Position Sensing Current Switch Encoder RPM Detection Notes: 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. Typical Application Circuit IA IB M Digital Hall Effect Sensor Driver & Control Logic IC Ia Ib Ic RPM sensing M: Three Phase Hall Motor HA HB HC Hall Motor Driver 3 Phase Hall Motor AH173 Document number: DS31044 Rev. 10 - 2 1 of 9 www.diodes.com July 2010 © Diodes Incorporated AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE Pin Descriptions Pin Name Vcc GND OUT Pin # 1 2 3 Ground Output Stage Description Positive Power Supply Functional Block Diagram VCC 1 REG. Rpu 3 AMP OUT 2 GND Absolute Maximum Ratings (TA = 25°C) Symbol VCC VOUT (off) IO (sink) Ts TJ PD Characteristics Supply Voltage Output “Off” Voltage Output “On” Current Storage Temperature Range Maximum Junction Temperature Power Dissipation SIP-3L SC59 Values 20 20 25 -65~+150 +150 550 230 Unit V V mA °C °C mW mW Recommended Operating Conditions Symbol VCC TA Characteristic Supply Voltage Operating Ambient Temperature Conditions Operating Operating Min 3 -40 Max 20 125 Unit V °C AH173 Document number: DS31044 Rev. 10 - 2 2 of 9 www.diodes.com July 2010 © Diodes Incorporated AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE Electrical Characteristics (TA = 25°C) Symbol VOUT (SAT) ICC Rpu Vd Characteristics Output Saturation Voltage Supply Current Internal Pull-up Resistor Dropout Voltage Vd = VCC - VCe Conditions VCC = 12V, OUT ”ON” IO = 10mA VCC = 12V, OUT ”OFF” Min 7 Typ. 300 3.5 10 Max 400 6 13 0.3 Unit mV mA KΩ V Magnetic Characteristics (TA = 25°C, Vcc = 12V, unless otherwise specified, Note 2) (1mT = 10 Gauss) A grade Symbol Bops(south pole to brand side) Brps(south pole to brand side) Bhy(|Bopx|-|Brpx|) B grade Symbol Bops(south pole to brand side) Brps(south pole to brand side) Bhy(|Bopx|-|Brpx|) Notes: Parameter Operation Point Release Point Hysteresis Min 15 -60 - Typ. 80 Max 60 -15 - Unit Gauss Gauss Gauss Parameter Operation Point Release Point Hysteresis Min 5 -80 - Typ. 80 Max 80 -5 - Unit Gauss Gauss Gauss 2. Magnetic characteristics may vary with supply voltage, operating temperature and after soldering. Operating Characteristics V out (Output Voltage) Vcc High S S Marking Side Vd Bhy Low Marking Side N (SC59) N (SIP-3L) VSAT Brp 0 Bop (Magnetic Flux Density) AH173 Document number: DS31044 Rev. 10 - 2 3 of 9 www.diodes.com July 2010 © Diodes Incorporated AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE Performance Characteristics (1) SIP-3L TA (°C) PD (mW) TA (°C) PD(mW) P D (m W ) 600 500 400 300 200 100 0 0 -4 0 25 50 75 100 125 150 T A ( °C ) 25 550 105 198 50 440 110 176 60 396 115 154 70 352 120 132 80 308 125 110 85 286 130 88 90 264 135 66 95 242 140 44 100 220 150 0 P o w e r D is s ip a tio n C u rve (2) SC59 (commonly known as SOT23 in Asia) TA (°C) PD (mW) 25 230 50 184 60 166 70 147 80 129 85 120 90 110 100 92 110 74 120 55 130 37 140 18 150 0 P D (m W ) 300 P o w e r D is s ip a tio n C u rv e 200 100 0 0 -4 0 25 50 75 100 125 150 T A ( °C ) AH173 Document number: DS31044 Rev. 10 - 2 4 of 9 www.diodes.com July 2010 © Diodes Incorporated AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE Ordering Information AH173 - X X - X - X Package P : SIP-3L W : SC59 Lead Free L : Lead Free G : Green (Note 3) Packing A : Ammo Box (Note 6) B : Bulk (Note 7) 7 : Tape & Reel 7” Tape and Reel Quantity NA NA NA NA NA NA NA NA 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel 3000/Tape & Reel Part Number Suffix NA NA NA NA NA NA NA NA -7 -7 -7 -7 Magnetic Characteristics A or B Device AH173-PL-A-A AH173-PL-A-B AH173-PG-A-A AH173-PG-A-B AH173-PL-B-A AH173-PL-B-B AH173-PG-B-A AH173-PG-B-B AH173-WL-7-A AH173-WL-7-B AH173-WG-7-A AH173-WG-7-B Notes: Tube/Bulk Package Packaging Part Code (Note 4, 5) Quantity Number Suffix P P P P P P P P W W W W SIP-3L SIP-3L SIP-3L SIP-3L SIP-3L SIP-3L SIP-3L SIP-3L SC59 SC59 SC59 SC59 NA NA NA NA 1000 1000 1000 1000 NA NA NA NA NA NA NA NA -B -B -B -B NA NA NA NA Ammo Box Quantity 4000/Box 4000/Box 4000/Box 4000/Box NA NA NA NA NA NA NA NA Part Number Suffix -A -A -A -A NA NA NA NA NA NA NA NA Magnetic Characteristics A B A B A B A B A B A B 3. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 4. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. 5. Reverse taping as shown on Diodes Inc. Surface Mount (SMD) Packaging document AP02007, which can be found on our website http://www.diodes.com/datasheets/ap02007.pdf. 6. Ammo Box is for SIP-3L Spread Lead. 7. Bulk is for SIP-3L Straight Lead. AH173 Document number: DS31044 Rev. 10 - 2 5 of 9 www.diodes.com July 2010 © Diodes Incorporated AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE Marking Information (1) SIP-3L (Top View) Part Number 173 Y WW X Y : Year : 0~9 WW : Week : 01~52, "52" represents 52 and 53 week X : Internal Code : A~Z : Green a~z : Lead Free (2) SC59 (Commonly known as SOT23 in Asia) (Top View) XX Y W X XX : Identification code Y : Year 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : A~Z : Green a~z : Lead Free Package SC59 Identification Code J3 Part Number AH173 AH173 Document number: DS31044 Rev. 10 - 2 6 of 9 www.diodes.com July 2010 © Diodes Incorporated AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE Package Outline Dimensions (All Dimensions in mm) (1) Package Type: SIP-3L for Bulk pack 0.51mm NOM 2.00 +/0.10mm 1.15 +/0.10mm BRANDED SURFACE 1 2 3 Active Area Depth Package Dimension Sensor Location AH173 Document number: DS31044 Rev. 10 - 2 7 of 9 www.diodes.com July 2010 © Diodes Incorporated AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE Package Outline Dimensions (Continued) (2) Package Type: SIP-3L for Ammo pack (3) SC59 (Commonly known as SOT23 in Asia) 0.35/0.50 TOP VIEW 1.50/ 1.70 2.70/ 3.00 1.90 2.90/3.10 1.00/ 1.30 0.10/0.20 0.013/0.10 0.95 0.35/0.55 0 O /8 O AH173 Document number: DS31044 Rev. 10 - 2 8 of 9 www.diodes.com July 2010 © Diodes Incorporated AH173 INTERNAL PULL-UP HALL EFFECT LATCH FOR HIGH TEMPERATURE IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2010, Diodes Incorporated www.diodes.com AH173 Document number: DS31044 Rev. 10 - 2 9 of 9 www.diodes.com July 2010 © Diodes Incorporated