AH175-WG-A-A

AH175 HALL EFFECT LATCH FOR HIGH TEMPERATURE Features • • • • • • • • • Bipolar Hall Effect Latch Sensor 3.5V to 20V DC Operation Voltage Open Collector Pre-Driver 25mA Output Sink Current Chip Power Reverse-Connection Protection o o Operating Temperature: -40 C~150 C Lead Free Finish/RoHS Compliant for Lead Free products (Note 1) Lead Free Packages: SIP-3L, SC59-3L Green Package: SC59-3L General Description AH175 is a single-digital-output Hall-effect sensor for high temperature operation. The device includes an on-chip Hall voltage generator for magnetic sensing, an amplifier to amplify Hall voltage, and a comparator to provide switching hysteresis for noise rejection, and an open-collector output pre-driver. An internal band-gap regulator is used to provide temperature compensated supply voltage for internal circuits and allows a wide operating supply range. While the magnetic flux density (B) is larger than threshold Bop, the OUT pin turns on (low). If B removed toward Brp, the OUT pin is latched “on” state prior to B < Brp. When B < Brp, the OUT pin goes into “off ” state. Applications • • • • Rotor Position Sensing Current Switch Encoder RPM Detection Ordering Information AH175 - X X X - X Package P: SIP-3L W: SC59-3L Lead-Free L : Lead Free G : Green (Note 3) Packing - 7 : Taping -B : Bulk (Note 4) -A : Ammo Box (Note 5) Magnetic Characteristics A or B Note: 1. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. Device AH175-P AH175-W Tube/Bulk Package Packaging Quantity Part Code (Note 2) Number Suffix P W SIP-3L SC59-3L 1000 NA -B NA 7” Tape and Reel Quantity Part Number Suffix NA 3000/Tape & Reel NA Ammo Box Quantity Part Number Suffix 4000/Box NA Lead-free -A NA -7 Note: 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. 3. Green is only available for SC59-3L 4. Bulk is for SIP-3 Straight Lead. 5. Ammo Box is for SIP-3 Spread Lead. AH175 Rev. 4 1 of 8 www.diodes.com FEBRUARY 2007 © Diodes Incorporated AH175 HALL EFFECT LATCH FOR HIGH TEMPERATURE Pin Assignment (Top View) 3. OUT 2. GND 1. VCC (SIP-3L package) Pin Description Name VCC GND OUT Description Input Power Ground Output Stage 3. OUT GND 2. 1. VCC (SC59-3L Package) Block Diagram VCC 1 REG. 3 AMP OUT 2 GND AH175 Rev. 4 2 of 8 www.diodes.com FEBRUARY 2007 © Diodes Incorporated AH175 HALL EFFECT LATCH FOR HIGH TEMPERATURE Absolute Maximum Ratings Parameter Supply Voltage Output “OFF ” Voltage Output “ON” Current Operating Temperature Range Storage Temperature Range Maximum Junction Temperature Power Dissipation (TA = 25°C) Symbol VCC Vout (off) Io (sink) Top Tstg Tj SIP-3L SC59-3L PD Rating 20 20 25 -40~+150 -65~+150 +150 550 230 Unit V V mA °C °C °C mW mW Recommended Operating Conditions Parameter Supply Voltage Symbol VCC Conditions Operating Rating 3.5 ~ 20 Unit V Electrical Characteristics Parameter Output Saturation Voltage Supply Current (TA = 25°C) Symbol Vout (SAT) ICC Conditions VCC = 12V, OUT ”ON” Io = 10mA VCC = 12V, OUT ”OFF” Min. - Typ. 300 3.5 Max. 400 6 Unit mV mA Magnetic Characteristics A grade Operation Point Release Point Hysteresis B grade Operation Point Release Point Hysteresis Symbol Bop Brp Bhy Symbol Bop Brp Bhy (TA = 25°C, VCC = 12V) (1mT = 10 Gauss) Min. 15 -60 30 Min. 5 -80 10 Typ. 80 Typ. 80 Max. 60 -15 120 Max. 80 -5 160 Unit Gauss Gauss Gauss Unit Gauss Gauss Gauss AH175 Rev. 4 3 of 8 www.diodes.com FEBRUARY 2007 © Diodes Incorporated AH175 HALL EFFECT LATCH FOR HIGH TEMPERATURE Operating Characteristics Vout (Output Voltage) Vcc High S S Marking side Vd Bhy Low Marking side N ( SC59 ) N (SIP3) VSAT Brp 0 Bop (Magnetic Flux Density) Performance Characteristics (SIP-3L) TA (°C) PD (mW) TA (°C) PD (mW) P D (m W ) 600 500 400 300 200 100 0 0 25 50 75 100 125 150 T A (oC ) 25 550 105 198 50 440 110 176 60 396 115 154 70 352 120 132 80 308 125 110 85 286 130 88 90 264 135 66 95 242 140 44 100 220 150 0 P o w e r D is s ip a tio n C u rv e AH175 Rev. 4 4 of 8 www.diodes.com FEBRUARY 2007 © Diodes Incorporated AH175 HALL EFFECT LATCH FOR HIGH TEMPERATURE Performance Characteristics (SC59-3L) TA (°C) PD (mW) P D (m W ) 300 25 230 50 184 60 166 70 147 80 129 90 110 100 92 110 74 120 55 125 46 130 37 140 18 150 0 P o w e r D is s ip a tio n C u rv e 200 100 0 0 25 50 75 100 125 150 T A (oC ) Marking Information (1) SC59-3L (Top View) 3 XX Y M X 1 2 XX : J5: AH175 Y : Year 0~9 M : Month A~L X : Internal code a~z: Lead Free A~Z: Green Part Number Package ATS137 (2) SIP3-3L (Top View) 175 Y WW X SC59-3L Identification Code JA Y : Year: “1”=2001 “2”=2002 WW: Nth Week 01~52 X : Internal code a~z: Lead Free AH175 Rev. 4 5 of 8 www.diodes.com FEBRUARY 2007 © Diodes Incorporated AH175 HALL EFFECT LATCH FOR HIGH TEMPERATURE Package Information (1) Package Type: SIP-3L for Bulk pack 0.51m m NO M 2.00m m 1.15m m BRANDED SURFACE 1 2 3 A ctive Area D epth Sensor Location Package Dimension AH175 Rev. 4 6 of 8 www.diodes.com FEBRUARY 2007 © Diodes Incorporated AH175 HALL EFFECT LATCH FOR HIGH TEMPERATURE Package Information (Continued) (2) Package Type: SIP-3L for Ammo pack AH175 Rev. 4 7 of 8 www.diodes.com FEBRUARY 2007 © Diodes Incorporated AH175 HALL EFFECT LATCH FOR HIGH TEMPERATURE Package Information (Continued) (3) Package Type: SC59-3L 0.35/0.50 1.50/ 1.70 TOP VIEW 2.70/ 3.00 1.90 2.90/3.10 1.00/ 1.30 0.10/0.20 0.013/0.10 0.95 0.35/0.55 0°/8° Sensor Location IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. AH175 Rev. 4 8 of 8 www.diodes.com FEBRUARY 2007 © Diodes Incorporated