AH1801-SNG-7

AH1801 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Features • • • • • Micropower operation Operation with North or South Pole 2.5V to 5.5V battery operation Inverted Output-on without Magnet present Chopper stabilized • Superior temperature stability • Extremely Low Switch-Point Drift • Insensitive to Physical Stress Good RF noise immunity -40°C to 85°C operating temperature Low profile 3 pin SC59 (commonly known as SOT23 in Asia) and DFN2020-3, DFN2020-6 package ESD (HBM) ＞ 5KV for DFN2020-3 and DFN2020-6 ＞ 6KV for SC59 SC59, DFN2020-3 and DFN2020-6: Available in “Green” Molding Compound (No Br, Sb) Lead Free Finish / RoHS Compliant (Note 1) General Description AH1801 is a Micropower, Ultra-sensitive Hall Effect Switch, which is with two Hall effect plates and a output driver, mainly designed for battery–operation, hand-held equipment (such as Cellular and Cordless Phone, PDA). The total operation power is down to 24uW in the 3V supply. Either north or south pole of sufficient strength will turn the output off. The output will be turned on under no magnetic field. While the magnetic flux density (B) is larger than operate point (Bop), the output will be turned off, the output is held until B is lower than release point (Brp), then turned on. • • • • • • Applications • • • Cellular phone PDA Cordless phone Ordering Information AH1801 - XX G - 7 Package W : SC59 FJ : DFN2020-3 SN : DFN2020-6 Device AH1801-WG-7 AH1801-FJG-7 AH1801-SNG-7 Notes: Green Packing 7 : Tape & Reel G : Green Package Code W FJ SN Packaging (Note 2) SC59 DFN2020-3 DFN2020-6 7” Tape and Reel Quantity Part Number Suffix 3000/Tape & Reel -7 3000/Tape & Reel -7 3000/Tape & Reel -7 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. AH1801 Rev. 7 1 of 10 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AH1801 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Pin Assignment (1) SC59 (2) DFN2020-3 ( Top View ) ( Top View ) 2. Output GND 3. 1. Vdd 3. GND 1. Vdd (3) DFN2020-6 3. Output ( Top View ) 6. NC 5. GND 4. NC 1. Vdd Notes: 2. NC 3. Output 3. NC is “No Connection”, which is recommended to be tied to ground. Pin Descriptions Pin Name Vdd GND Output NC P/I/O P/I P/I O Description Power Supply Input Ground Output Pin No Connected AH1801 Rev. 7 2 of 10 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AH1801 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Block Diagram 1 Power switch Offset Cancelling Offset Cancelling Hall Plate Output Amp Latch Vdd 3 Logical GND 2 Hall Plate Amp Latch Typical Circuit 2.5~5.5V RL C AH1801 GND Output Notes: 4. C is for power stabilization and to strengthen the noise immunity, the recommended capacitance is 10nF~100nF. RL is the pull-up resistor, the recommended resistance is 10KΩ~100KΩ. AH1801 Rev. 7 3 of 10 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AH1801 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Absolute Maximum Ratings Symbol Vdd B Ts PD TJ (at TA = 25°C) Characteristics Supply voltage Magnetic flux density Storage Temperature Range Package Power Dissipation Maximum Junction Temp SC59 DFN2020-3 DFN2020-6 Values 7 Unlimited -65 to +150 230 150 Unit V °C mW °C Recommended Operating Conditions Symbol Vdd TA Parameter Supply Voltage Operating Temperature Range (TA = 25°C) Conditions Operating Operating Rating 2.5~5.5 -40 to +85 Unit V °C AH1801 Rev. 7 4 of 10 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AH1801 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Electrical Characteristics Symbol Vout Ioff Idd(en) Characteristic Output On Voltage Output Leakage Current (TA = +25°C, Vdd = 3V; unless otherwise specified) Conditions Iout = 1mA Vout = 5.5V, Output off Chip enable, TA = 25°C, Vdd = 3V Chip enable, TA = -40~85°C, Vdd = 2.5~5.5V Chip disable, TA = 25°C, Vdd = 3V Chip disable, TA = -40~85°C, Vdd = 2.5~5.5V Average supply current, TA = 25°C, Vdd = 3V Average supply current, TA = -40~85°C, Vdd = 2.5~5.5V (Note 5) (Note 5) Min - Typ 0.1