AP1117D33G-U

AP1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Features • • • • • • • • • 1.4V Maximum Dropout at Full Load Current Fast Transient Response Output Current Limiting Built-in Thermal Shutdown Good Noise Rejection 3-Terminal Adjustable or Fixed 1.5V, 1.8V, 2.5V, 3.3V, 5.0V SOT223-3L, TO252-3L, SOT89-3L, TO263-3L and TO220-3L Packages SOT223-3L and TO252-3L: Available in “Green” Molding Compound (No Br, Sb) Lead Free Finish/RoHS Compliant (Note 1) General Description AP1117 is a low dropout positive adjustable or fixed-mode regulator with 1A output current capability. The product is voltage specifically designed to provide well-regulated supply for low IC applications such as high-speed bus termination and low current 3.3V logic supply. AP1117 is also well suited for other applications such as VGA cards. AP1117 is guaranteed to have lower than 1.4V dropout at full load current making it ideal to provide well-regulated outputs of 1.25 to 5.0 with 6.4V to 18V input supply. AP1117 is available in both commercial and industrial temperature grade. Applications • • PC Peripheral Communication Ordering Information A P 1 1 1 7 X XX X X Package D : TO252-3L E : SOT223-3L K : TO263-3L T : TO220-3L Y : SOT89-3L Vout Blank: Adj 15: 1.5V 18: 1.8V 25: 2.5V 33: 3.3V 50: 5.0V Lead Free L : Lead Free G : Green (Note 1) Packing - U : Tube -13 : Taping Note: 1. Green is only for SOT223-3L and TO252-3L. 2. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. Device AP1117D AP1117E AP1117K AP1117T AP1117Y Package Code D E K T Y Packaging (Note 3) TO252-3L SOT223-3L TO263-3L TO220-3L SOT89-3L Tube Part Number Quantity Suffix 80 75 50 50 NA -U -U -U -U NA 13” Tape and Reel Part Number Quantity Suffix 2500/Tape & Reel 2500/Tape & Reel 800/Tape & Reel NA 2500/Tape & Reel -13 -13 -13 NA -13 Lead-free Lead-free Lead-free Note: 3. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. AP1117 Rev. 6 1 of 11 www.diodes.com MARCH 2007 © Diodes Incorporated AP1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Pin Assignments SOT223-3L ( Top View ) 3 2 1 Tab is Vout Vin Vout Adj (GND) SOT89-3L 3 2 1 Tab is Vout Vin Vout Adj (GND) TO220-3L FRONT VIEW 3 2 1 Tab is V out Vin Vout Adj (GND) TO252-3L / TO263-3L ( Top View ) 3 2 1 Tab is Vout Vin Vout Adj (GND) Pin Descriptions NAME Adj (GND) Vout I/O I O PIN # 1 2 FUNCTION A resistor divider from this pin to the Vout pin and ground sets the output voltage (Ground only for Fixed-Mode). The output of the regulator. A minimum of 10uF capacitor (0.15Ω ≤ ESR ≤ 20Ω) must be connected from this pin to ground to insure stability. The input pin of regulator. Typically a large storage capacitor (0.15Ω ≤ ESR ≤ 20Ω) is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.3V higher than Vout in order for the device to regulate properly. Vin I 3 AP1117 Rev. 6 2 of 11 www.diodes.com MARCH 2007 © Diodes Incorporated AP1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Block Diagram Vin 3 2 Vout + CURRENT LIMIT + 1.25V + 1 + Thermal Shutdown GND (FIXED) 1 Adj Absolute Maximum Ratings Symbol Vin TOP TMJ DC Supply Voltage Operating Junction Temperature Range (Commercial Grade) Maximum Junction Temperature Power Dissipation SOT89-3L SOT223-3L TO220-3L TO252-3L TO263-3L Storage Temperature Internally limited by maximum junction temperature of 150 oC (Note 4) -65 to +150 Parameter Rating -0.3 to 18 0 to +125 150 Unit V oC oC - PD mW TST Note: 4. oC AP1117 contains an internal thermal limiting circuit that is designed to protect the regulator in the event that the maximum junction temperature exceeded. When activated, typically at 150°C, the regulator output switches off and then back on as the die cools. AP1117 Rev. 6 3 of 11 www.diodes.com MARCH 2007 © Diodes Incorporated AP1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Electrical Characteristics PARAMETER Reference Voltage AP1117-ADJ AP1117-1.5 AP1117-1.8 Output Voltage AP1117-2.5 AP1117-3.3 AP1117-5.0 Line Regulation AP1117-XXX AP1117-ADJ AP1117-1.5 AP1117-1.8 Load Regulation AP1117-2.5 AP1117-3.3 AP1117-5.0 Dropout Voltage (VIN-VOUT) Current Limit Minimum Load Current (Note 7) Thermal Regulation Ripple Rejection Temperature Stability (Under Operating Conditions) CONDITIONS TA = 25 C, (VIN-OUT) = 1.5V IO = 10mA o IOUT = 10mA, TA = 25 C, 3V≦VIN≦12V o IOUT = 10mA, TA = 25 C, 3.3V≦VIN≦12V o IOUT = 10mA, TA = 25 C, 4V≦VIN≦12V o IOUT = 10mA, TA = 25 C, 4.8V≦VIN≦12V o IOUT = 10mA, TA = 25 C, 6.5V≦VIN≦12V IO = 10mA,VOUT+1.5V