ES2AA

ES2A/A - ES2D/A 2.0A SURFACE MOUNT SUPER-FAST RECTIFIER Features · · · · · · Glass Passivated Die Construction Super-Fast Recovery Time For High Efficiency Low Forward Voltage Drop and High Current Capability Surge Overload Rating to 50A Peak Ideally Suited for Automated Assembly Plastic Material: UL Flammability Classification Rating 94V-0 B Dim A SMA Min 2.29 4.00 1.27 0.15 4.80 0.10 0.76 2.01 Max 2.92 4.60 1.63 0.31 5.59 0.20 1.52 2.62 SMB Min 3.30 4.06 1.96 0.15 5.00 0.10 0.76 2.00 Max 3.94 4.57 2.21 0.31 5.59 0.20 1.52 2.62 A C B C D Mechanical Data · · · · · · · Case: Molded Plastic Terminals: Solder Plated Terminal Solderable per MIL-STD-202, Method 208 Polarity: Cathode Band or Cathode Notch SMA Weight: 0.064 grams (approx.) SMB Weight: 0.093 grams (approx.) Mounting Position: Any Marking: Type Number J D E G H J H G E All Dimensions in mm AA, BA, CA, DA Suffix Designates SMA Package A, B, C, D, Suffix Designates SMB Package Maximum Ratings and Electrical Characteristics Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current @ TT = 110°C Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load (JEDEC Method) Forward Voltage Peak Reverse Current at Rated DC Blocking Voltage Reverse Recovery Time (Note 3) Typical Junction Capacitance (Note 2) Typical Thermal Resistance, Junction to Terminal (Note 1) Operating and Storage Temperature Range @ IF = 2.0A @ TA = 25°C @ TA = 125°C Symbol VRRM VRWM VR VR(RMS) IO IFSM VFM IRM trr Cj RqJT Tj, TSTG @ TA = 25°C unless otherwise specified ES2A/A 50 35 ES2B/A 100 70 2.0 50 0.92 5.0 350 25 25 20 ES2C/A 150 105 ES2D/A 200 140 Unit V V A A V mA ns pF °C/W °C -55 to +150 Notes: 1. Unit mounted on PC board with 5.0 mm2 (0.013 mm thick) copper pads as heat sink. 2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC. 3. Measured with IF = 0.5A, IR = 1.0A, Irr = 0.25A. See Figure 5. DS14002 Rev. F-2 1 of 2 ES2A/A - ES2D/A IF, INSTANTANEOUS FORWARD CURRENT (A) 0.75 10 IO, AVERAGE FORWARD CURRENT (A) Tj = 25°C Pulse width = 300µs 2.0 1.6 1.0 1.2 0.8 0.4 0.1 0 25 50 75 100 125 150 175 TT, TERMINAL TEMPERATURE (°C) Fig. 1 Forward Current Derating Curve 0.01 0 0.4 0.8 1.2 1.6 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics IFSM, PEAK FORWARD SURGE CURRENT (A) Single Half-Sine-Wave (JEDEC Method) 50 IR, INSTANTANEOUS REVERSE CURRENT (µA) 60 1000 Tj = 125°C 100 40 30 20 10 Tj = 25°C 1.0 10 0 1 10 NUMBER OF CYCLES AT 60Hz Fig. 3 Surge Current Derating Curve 100 0.1 0 40 80 120 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) Fig. 4 Typical Reverse Characteristics trr +0.5A 50Ω NI (Non-inductive) Device Under Test 10Ω NI (-) Pulse Generator (Note 2) 0A (+) 50V DC Approx -0.25A (-) 1.0Ω NI Oscilloscope (Note 1) (+) Notes: 1. Rise Time = 7.0ns max. Input Impedance = 1.0MΩ, 22pF. 2. Rise Time = 10ns max. Input Impedance = 50Ω. -1.0A Set time base for 50/100 ns/cm Fig. 5 Reverse Recovery Time Characteristic and Test Circuit DS14002 Rev. F-2 2 of 2 ES2A/A - ES2D/A