ES2G-13-F

SPICE MODELS: ES2A ES2B ES2C ES2D ES2AA ES2BA ES2CA ES2DA ES2A/A - ES2D/A 2.0A SURFACE MOUNT SUPER-FAST RECTIFIER Features · · · · · Glass Passivated Die Construction Super-Fast Recovery Time For High Efficiency Surge Overload Rating to 50A Peak Ideally Suited for Automated Assembly Lead Free Finish/RoHS Complaint (Note 4) B Dim A SMA Min 2.29 4.00 1.27 0.15 4.80 0.10 0.76 2.01 Max 2.92 4.60 1.63 0.31 5.59 0.20 1.52 2.30 SMB Min 3.30 4.06 1.96 0.15 5.00 0.10 0.76 2.00 Max 3.94 4.57 2.21 0.31 5.59 0.20 1.52 2.40 Mechanical Data · · · · · · · · · Case: SMA/SMB Case Material: Molded Plastic. UL Flammability Classification Rating 94V-0 Moisture Sensitivity: Level 1 per J-STD-020C Terminals: Lead Free Plating (Matte Tin Finish). Solderable per MIL-STD-202, Method 208 Polarity: Cathode Band or Cathode Notch Marking Information: See Page 3 Ordering Information: See Page 3 SMA Weight: 0.064 grams (approximate) SMB Weight: 0.093 grams (approximate) A C B C D E G H D J e3 H G E J All Dimensions in mm AA, BA, CA, DA Suffix Designates SMA Package A, B, C, D, Suffix Designates SMB Package Maximum Ratings and Electrical Characteristics Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage (Note 5) RMS Reverse Voltage Average Rectified Output Current @ TT = 110°C Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Forward Voltage Peak Reverse Current at Rated DC Blocking Voltage (Note 5) Reverse Recovery Time (Note 3) Typical Total Capacitance (Note 2) Typical Thermal Resistance, Junction to Terminal (Note 1) Operating and Storage Temperature Range @ IF = 2.0A @ TA = 25°C @ TA = 125°C Symbol VRRM VRWM VR VR(RMS) IO IFSM VFM IRM trr CT RqJT Tj, TSTG @ TA = 25°C unless otherwise specified ES2A/A 50 35 ES2B/A 100 70 2.0 50 0.92 5.0 350 25 25 20 ES2C/A 150 105 ES2D/A 200 140 Unit V V A A V mA ns pF °C/W °C -55 to +150 Notes: 1. 2. 3. 4. 5. Unit mounted on PC board with 5.0 mm2 (0.013 mm thick) copper pads as heat sink. Measured at 1.0MHz and applied reverse voltage of 4.0V DC. Measured with IF = 0.5A, IR = 1.0A, Irr = 0.25A. See Figure 5. RoHS revision 13.2.2003. Glass and high temperature solder exemptions applied, see EU Directive Annex Notes 5 and 7. Short duration pulse test used to minimize self-heating effect. DS14002 Rev. 10 - 2 1 of 3 www.diodes.com ES2A/A - ES2D/A ã Diodes Incorporated IF, INSTANTANEOUS FORWARD CURRENT (A) 2.4 IO, AVERAGE FORWARD CURRENT (A) 2.0 1.6 10 Tj = 25oC 1.0 1.2 0.8 0.4 0.1 0 25 50 75 100 125 150 175 0.01 0 0.4 0.8 1.2 1.6 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics TT, TERMINAL TEMPERATURE (° C) Fig. 1 Forward Current Derating Curve IFSM, PEAK FORWARD SURGE CURRENT (A) 60 Single Half-Sine-Wave 1000 50 100 Tj = 125° C 40 30 20 1.0 10 Tj = 25° C 10 0 1 10 NUMBER OF CYCLES AT 60Hz Fig. 3 Surge Current Derating Curve 100 0.1 0 40 80 120 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) Fig. 4 Typical Reverse Characteristics trr +0.5A Device Under Test (-) Pulse Generator (Note 2) 0A (+) 50V DC Approx -0.25A (-) Oscilloscope (Note 1) (+) -1.0A Set time base for 50/100 ns/cm Fig. 5 Reverse Recovery Time Characteristic and Test Circuit DS14002 Rev. 10 - 2 2 of 3 www.diodes.com ES2A/A - ES2D/A Ordering Information Device ES2xA-13-F ES2x-13-F (Note 6) Packaging SMA SMB Shipping 5000/Tape & Reel 3000/Tape & Reel * x = Device type, e.g. ES2BA-13-F (SMA package); ES2A-13-F (SMB package). Notes: 6. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information ES2XA = Product type marking code, ex: ES2BA (SMA package) ES2X = Product type marking code, ex: ES2A (SMB package) = Manufacturers’ code marking YWW = Date code marking Y = Last digit of year ex: 2 for 2002 WW = Week code 01 to 52 YWW ES2X(A) IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. DS14002 Rev. 10 - 2 3 of 3 www.diodes.com ES2A/A - ES2D/A