PDR5G-13

PDR5G 5A GLASS PASSIVATED RECTIFIER PowerDI ä5 Features · · · · · Glass Passivated Die Construction Low Leakage Current Lead Free Finish, RoHS Compliant (Note 1) "Green" Molding Compound (No Br, Sb) Qualified to AEC-Q101 Standards for High Reliability L1 e b1 D D2 b2 L E2 E D b2 L1 A A2 PowerDIä5 E E1 Dim A A2 b1 Min 1.05 0.33 0.80 1.70 3.90 6.40 5.30 0.75 0.50 1.20 Max 1.15 0.43 0.99 1.88 4.05 6.60 5.45 0.95 0.65 1.50 Mechanical Data · · · · · · · Case: PowerDI 5 Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 Moisture Sensitivity: Level 1 per J-STD-020C Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 Polarity: See Diagram Marking: See Page 3 Weight: 0.096 grams (approximate) ä b1 A2 b2 D D2 E e E1 E2 L L1 3.05 NOM 1.84 NOM 3.55 NOM W e3 e b1 LEFT PIN RIGHT PIN L1 b1 BOTTOMSIDE HEAT SINK W Note: Pins Left & Right must be electrically connected at the printed circuit board. All Dimensions in mm Maximum Ratings @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (See also figure 4) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Symbol VRRM VRWM VR VR(RMS) IO IFSM Value 400 283 5 100 Unit V V A A Thermal Characteristics Characteristic Thermal Resistance Junction to Soldering Point Thermal Resistance Junction to Ambient Air (Note 2) Thermal Resistance Junction to Ambient Air (Note 3) Thermal Resistance Junction to Ambient Air (Note 4) Operating Temperature Range Storage Temperature Range Notes: 1. 2. 3. 4. Symbol RqJS RqJA RqJA RqJA Tj TSTG Typ ¾ 75 65 45 ¾ ¾ Max 1.5 ¾ ¾ ¾ -65 to +150 -65 to +150 Unit °C/W °C/W °C/W °C/W °C °C RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. TA = 25°C Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. TA = 25°C Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. TA = 25°C DS30552 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 3 www.diodes.com PDR5G ã Diodes Incorporated Electrical Characteristics Characteristic Reverse Breakdown Voltage (Note 5) Forward Voltage Reverse Leakage Current (Note 5) Reverse Recovery Time Notes: 2. 3. 4. 5. 6. @ TA = 25°C unless otherwise specified Symbol V(BR)R VF IR trr Min 400 ¾ ¾ ¾ ¾ Typ ¾ 0.92 0.02 9 3.3 Max ¾ 1.15 10 250 ¾ Unit V V mA ms Test Condition IR = 10mA IF = 5A, TS = 25°C TS = 25°C, VR = 400V TS = 125°C, VR = 400V IF = 0.5A, IR = 1.0A, Irr = 0.25A FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. TA = 25°C Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. TA = 25°C Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. TA = 25°C Short duration test pulse used to minimize self-heating effect. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 18.8mm x 14.4mm. Anode pad dimensions 5.6mm x 3.0mm. IF, INSTANTANEOUS FORWARD CURRENT (A) 100 10 1 Tj = 150°C IR, INSTANTANEOUS REVERSE CURRENT (A) Tj = +150°C Tj = +125°C 100m 10m 1m Tj = 85°C Tj = +85°C 100n Tj = +25°C Tj = 25°C 10n Tj = -65°C Tj = -65°C 1n 0 80 160 240 0 0.2 0.4 0.6 0.8 1.0 1.2 320 400 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 1 Typical Forward Characteristics VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics 7.5 100 f = 1 MHz CT, TOTAL CAPACITANCE (pF) IF, DC FORWARD CURRENT (A) 75 6.0 4.5 Note 6 50 3.0 25 1.5 Note 2 0 0 5 10 15 20 25 30 0 0 25 50 75 100 125 150 175 TA, AMBIENT TEMPERATURE (°C) Fig. 4 DC Forward Current Derating VR, REVERSE VOLTAGE (V) Fig. 3 Typical Total Capacitance vs. Reverse Voltage DS30552 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 2 of 3 www.diodes.com PDR5G 4 IPK = 1 (DC) IAV 180 TA, DERATED AMBIENT TEMPERATURE (°C) PF, FORWARD POWER DISSIPATION (W) 150 3 120 2 90 60 1 30 0 0 1 2 3 4 5 IF, FORWARD CURRENT (A) Fig. 5 Forward Power Dissipation 0 0 100 200 300 400 VR, DC REVERSE VOLTAGE (V) Fig. 6 Operating Temperature Derating Ordering Information Device PDR5G-13 Notes: (Note 7) Packaging PowerDIä5 Shipping 5000/Tape & Reel 7. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information R5G YYWWK R5G = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last two digits of year ex: 05 for 2005 WW = Week code 01 to 52 K = Factory Designator IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. DS30552 Rev. 6 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 3 www.diodes.com PDR5G