PDS1040CTL

SPICE MODEL: PDS1040CTL PDS1040CTL 10A DUAL LOW VF SCHOTTKY BARRIER RECTIFIER PowerDI ä5 Features NEW PRODUCT · · · · · · · · · Guard Ring Die Construction for Transient Protection Low Power Loss, High Efficiency Low Forward Voltage Drop Very Low Reverse Leakage Current For Use in Low Voltage, High Frequency Inverters, OR’ing, and Polarity Protection Applications High Forward Surge Current Capability Lead Free Finish, RoHS Compliant (Note 1) "Green" Molding Compound (No Br, Sb) Qualified to AEC-Q101 Standards for High Reliability BOTTOMSIDE b1 HEAT SINK D b2 L1 A A2 PowerDIä5 Dim E Min 1.05 0.33 0.80 1.70 3.90 6.40 5.30 0.75 0.50 1.20 Max 1.15 0.43 0.99 1.88 4.05 6.60 5.45 0.95 0.65 1.50 E1 A A2 b1 L1 e b1 D D2 b2 L E2 E A2 b2 D D2 E e E1 E2 L L1 W Mechanical Data · · · · · · · Case: PowerDI 5 Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 Moisture Sensitivity: Level 1 per J-STD-020C Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 Polarity: See Diagram Marking: See Page 3 Weight: 0.096 grams (approx.) LEFT PIN RIGHT PIN 3.05 NOM 1.84 NOM 3.55 NOM ä W L1 e e3 b1 b1 BOTTOMSIDE HEAT SINK TOP VIEW All Dimensions in mm Maximum Ratings @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (See also Figure 5) per element total device Symbol VRRM VRWM VR VR(RMS) IO IFSM Tj TSTG @ TA = 25°C unless otherwise specified Symbol RqJS RqJA RqJA RqJA Typ ¾ 95 75 50 Max 2.0 ¾ ¾ ¾ Unit °C/W °C/W °C/W °C/W Value 40 28 5 10 110 -65 to +150 -65 to +150 Unit V V A A °C °C Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Per element Operating Temperature Range Storage Temperature Range Thermal Characteristics Characteristic Thermal Resistance Junction to Soldering Point Thermal Resistance Junction to Ambient Air (Note 2) Thermal Resistance Junction to Ambient Air (Note 3) Thermal Resistance Junction to Ambient Air (Note 4) Notes: 1. 2. 3. 4. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. DS30485 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 3 www.diodes.com PDS1040CTL ã Diodes Incorporated Electrical Characteristics @ TA = 25°C unless otherwise specified Symbol V(BR)R Min 40 ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ Typ ¾ 0.465 0.41 0.39 0.55 0.53 0.52 20 3 15 2.5 6 1 Max ¾ 0.50 0.45 0.43 0.60 0.57 0.56 200 25 150 10 80 5 Unit V Test Condition IR = 500mA IF = 5A, Ts = 25°C IF = 5A, Ts = 100°C IF = 5A, Ts = 125°C IF = 10A, Ts = 25°C IF = 10A, Ts = 100°C IF = 10A, Ts = 125°C VR = 40V, Ts = 25°C VR = 40V, Ts = 100°C VR = 35V, Ts = 25°C VR = 35V, Ts = 100°C VR = 17.5V, Ts = 25°C VR = 17.5V, Ts = 100°C NEW PRODUCT Characteristic Reverse Breakdown Voltage (Note 5) Forward Voltage Per Element VF V Reverse Leakage Current (Note 5) Per Element IR mA mA mA mA mA mA Notes: 5. Short duration test pulse used to minimize self-heating effect. IF, INSTANTANEOUS FORWARD CURRENT (A) 100 10 100 Tj = +25° C 10 1 0.1 Tj = 100°C Tj = 150°C Tj = 125°C 1 0.01 Tj = 85°C 0.1 0.001 Tj = 25°C 0.0001 Tj = -65°C 0.01 Tj = -65°C 0.00001 0 100 200 300 400 500 600 700 VF, INSTANTANEOUS FORWARD VOLTAGE (mV) Fig. 1 Typical Forward Characteristics, Per Element 0.001 0 5 10 15 20 25 30 35 40 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics, Per Element 800 f = 1 MHz IR, INSTANTANEOUS REVERSE CURRENT (mA) 1,000 700 100 Tj = +150°C CT, TOTAL CAPACITANCE (pF) Tj = +85°C 600 500 400 300 200 100 10 Tj = +125°C Tj = +100°C 1 0.1 0 10 20 30 40 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 3 Typical Reverse Characteristics, Per Element 0 5 10 15 20 25 30 35 40 VR, REVERSE VOLTAGE (V) Fig. 4 Typical Total Capacitance vs. Reverse Voltage, Per Element DS30485 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 2 of 3 www.diodes.com PDS1040CTL 7.5 4 PF, FORWARD POWER DISSIPATION (W) NEW PRODUCT IF, DC FORWARD CURRENT (A) 6.0 IPK = 1 (DC) IAV 3 4.5 Note 4 2 3.0 Note 2 1.5 1 0 0 25 50 75 100 125 150 TA, AMBIENT TEMPERATURE (°C) Fig. 5 DC Forward Current Derating, Per Element 200 0 0 1 2 3 4 5 6 7 8 9 10 IF, FORWARD CURRENT (A) Fig. 6 Forward Power Dissipation, Per Element TA, DERATED AMBIENT TEMPERATURE (°C) Note 2 160 120 80 40 0 0 10 20 30 40 VR, DC REVERSE VOLTAGE (V) Fig. 7 Operating Temperature Derating, Per Element Ordering Information Device (Note 6) Packaging PowerDIä5 Shipping 5000/Tape & Reel PDS1040CTL-13 Notes: 2. 3. 4. 5. 6. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polyimide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. Short duration test pulse used to minimize self-heating effect. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information S1040CTL = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last digit of year ex: 04 for 2004 WW = Week code 01 to 52 K = Factory Designator Code S1040CTL YYWWK DS30485 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 3 www.diodes.com PDS1040CTL