PDS1040L-13

SPICE MODEL: PDS1040L PDS1040L 10A LOW VF SCHOTTKY BARRIER RECTIFIER PowerDI ä5 Features NEW PRODUCT · · · · · · · Guard Ring Die Construction for Transient Protection Very Low Forward Voltage Drop High Forward Surge Current Capability For Use in Low Voltage, High Frequency Inverters, Free Wheeling, and Polarity Protection Applications Lead Free Finish, RoHS Compliant (Note 1) "Green" Molding Compound (No Br, Sb) Qualified to AEC-Q101 Standards for High Reliability b1 L1 L1 D b2 A A2 PowerDIä5 E E1 Dim A A2 b1 Min 1.05 0.33 0.80 1.70 3.90 6.40 5.30 0.75 0.50 1.20 Max 1.15 0.43 0.99 1.88 4.05 6.60 5.45 0.95 0.65 1.50 e b1 D D2 b2 L E2 E A2 b2 D D2 E e E1 E2 L L1 W Mechanical Data · · · · · · · Case: PowerDI 5 Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 Moisture sensitivity: Level 1 per J-STD-020C Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 Polarity: See Diagram Marking: See Page 3 Weight: 0.096 grams (approx.) ä 3.05 NOM 1.84 NOM 3.55 NOM W L1 e e3 b1 LEFT PIN RIGHT PIN b1 BOTTOMSIDE HEAT SINK Note: Pins Left & Right must be electrically connected at the printed circuit board. All Dimensions in mm Maximum Ratings @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (see also Figure 5) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Operating Junction Temperature Range Storage Temperature Range VR £ 80% VRRM VR £ 50% VRRM Symbol VRRM VRWM VR VR(RMS) IO IFSM TJ TSTG @ TA = 25°C unless otherwise specified Symbol RqJS RqJA RqJA RqJA Typ ¾ 85 65 50 Max 1.5 ¾ ¾ ¾ Unit °C/W °C/W °C/W °C/W Value 40 28 10 275 -65 to +130 -65 to +150 -65 to +150 Unit V V A A °C °C Thermal Characteristics Characteristic Thermal Resistance Junction to Soldering Point Thermal Resistance Junction to Ambient Air (Note 2) Thermal Resistance Junction to Ambient Air (Note 3) Thermal Resistance Junction to Ambient Air (Note 4) Notes: 1. 2. 3. 4. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. DS30486 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 3 www.diodes.com PDS1040L ã Diodes Incorporated Electrical Characteristics @ TA = 25°C unless otherwise specified Symbol V(BR)R Min 40 ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ Typ ¾ 0.41 0.30 0.42 0.32 0.44 0.35 0.07 12.5 Max ¾ 0.46 0.35 0.47 0.41 0.49 0.43 0.6 25 Unit V Test Condition IR = 600mA IF = 6A, TS = 25°C IF = 6A, TS = 125°C IF = 8A, TS = 25°C IF = 8A, TS = 125°C IF = 10A, TS = 25°C IF = 10A, TS = 125°C TS = 25°C, VR = 40V TS = 100°C, VR = 40V NEW PRODUCT Characteristic Reverse Breakdown Voltage (Note 5) Forward Voltage VF V Reverse Current (Note 5) Notes: 5. Short duration test pulse used to minimize self-heating effect. IR mA IF, INSTANTANEOUS FORWARD CURRENT (A) 100 10 1 100m 10m 1m Tj = 25°C Tj = -65°C Tj = 125°C Tj = 150°C Tj = +25°C Tj = 100°C Tj = 85°C 100n 10n 1n 100r Tj = -65°C 0 100 200 300 400 500 600 0 10 20 30 40 IR, INSTANTANEOUS REVERSE CURRENT (mA) VF, INSTANTANEOUS FORWARD VOLTAGE (mV) Fig. 1 Typical Forward Characteristics 1,000 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics 10,000 f = 1MHz 100 Tj = 150°C Tj = 125°C CT, TOTAL CAPACITANCE (pF) 1,000 10 Tj = 100°C Tj = 85°C 1.0 0 10 20 30 40 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 3 Typical Reverse Characteristics 100 0 5 10 15 20 25 30 35 40 VR, REVERSE VOLTAGE (V) Fig. 4 Typical Total Capacitance vs. Reverse Voltage DS30486 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 2 of 3 www.diodes.com PDS1040L 12.5 4 IPK = 1 (DC) IAV NEW PRODUCT 10 PF(AV), AVERAGE FORWARD POWER DISSIPATION (W) IF, DC FORWARD CURRENT (A) 3 7.5 Note 6 2 5.0 1 2.5 Note 2 0 0 25 50 75 100 125 150 TA, AMBIENT TEMPERATURE (°C) Fig. 5 DC Forward Current Derating 170 0 0 12 15 6 9 3 IF(AV), AVERAGE FORWARD CURRENT (A) Fig. 6 Forward Power Dissipation TA, DERATED AMBIENT TEMPERATURE (°C) 150 130 110 90 70 50 30 10 -10 -30 0 10 20 30 40 VR, DC REVERSE VOLTAGE (V) Fig. 7 Operating Temperature Derating Note 2 Note 7 Ordering Information Device PDS1040L-13 Notes: 2. 3. 4. 5. 6. 7. 8. (Note 8) Packaging PowerDIä5 Shipping 5000/Tape & Reel FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. Short duration test pulse used to minimize self-heating effect. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 18.8mm x 14.4mm. Anode pad dimensions 5.6mm x 3.0mm. Devices mounted such that RqJA @ 19°C/W. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information S1040L YYWWK S1040L = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last two digits of year ex: 04 for 2004 WW = Week code 01 to 52 K = Factory designator DS30486 Rev. 8 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 3 www.diodes.com PDS1040L