PDS5100H

SPICE MODEL: PDS5100H PDS5100H 5A HIGH VOLTAGE SCHOTTKY BARRIER RECTIFIER PowerDI ä5 Features · · · · · · · · · Guard Ring Die Construction for Transient Protection High Maximum Junction Temperature Very Low Leakage Current Highly Stable Oxide Passivated Junction Low Forward Voltage Drop High Forward Surge Current Capability Lead Free Finish, RoHS Compliant (Note 1) "Green" Molding Compound (No Br, Sb) Qualified to AEC-Q101 Standards for High Reliability L1 e b1 D D2 b2 L E2 E E D b2 L1 A A2 PowerDIä5 Dim E1 Min 1.05 0.33 0.80 1.70 3.90 6.40 5.30 0.75 0.50 1.20 Max 1.15 0.43 0.99 1.88 4.05 6.60 5.45 0.95 0.65 1.50 A A2 b1 b1 A2 b2 D D2 E e E1 E2 L L1 Mechanical Data · · · · · · · Case: PowerDI 5 Case Material: Molded Plastic, “Green” Molding Compound. UL Flammability Classification Rating 94V-0 Moisture Sensitivity: Level 1 per J-STD-020C Terminals: Finish – Matte Tin annealed over Copper leadframe. Solderable per MIL-STD-202, Method 208 Polarity: See Diagram Marking: See Page 3 Weight: 0.096 grams (approximate) LEFT PIN RIGHT PIN 3.05 NOM 1.84 NOM 3.55 NOM ä W L1 e e3 b1 b1 BOTTOMSIDE HEAT SINK W All Dimensions in mm Note: Pins Left & Right must be electrically connected at the printed circuit board. Maximum Ratings @ TA = 25°C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current (See also figure 5) Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load Symbol VRRM VRWM VR VR(RMS) IO IFSM Value 100 71 5 250 Unit V V A A Thermal Characteristics Characteristic Thermal Resistance Junction to Soldering Point Thermal Resistance Junction to Ambient Air (Note 2) TA = 25°C Thermal Resistance Junction to Ambient Air (Note 3) TA = 25°C Thermal Resistance Junction to Ambient Air (Note 4) TA = 25°C Operating Temperature Range Storage Temperature Range Notes: 1. 2. 3. 4. Symbol RqJS RqJA RqJA RqJA Tj TSTG Typ ¾ 85 70 45 -65 to +175 -65 to +175 Max 2.0 ¾ ¾ ¾ Unit °C/W °C/W °C/W °C/W °C °C RoHS revision 13.2.2003. High Temperature Solder Exemption Applied, see EU Directive Annex Note 7. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. DS30471 Rev. 18 - 2 PowerDI is a trademark of Diodes Incorporated. 1 of 4 www.diodes.com PDS5100H ã Diodes Incorporated Electrical Characteristics Characteristic Reverse Breakdown Voltage (Note 5) Forward Voltage @ TA = 25°C unless otherwise specified Symbol V(BR)R VF Min 100 ¾ ¾ ¾ ¾ ¾ ¾ Typ ¾ 0.67 0.55 0.75 0.62 0.3 0.5 Max ¾ 0.71 0.58 0.80 0.66 3.5 4.5 Unit V V mA mA Test Condition IR = 3.5mA IF = 5A, TS = 25°C IF = 5A, TS = 125°C IF = 10A, TS = 25°C IF = 10A, TS = 125°C TS = 25°C, VR = 100V TS = 125°C, VR = 100V Reverse Leakage Current (Note 5) Notes: IR 5. Short duration test pulse used to minimize self-heating effect. IF, INSTANTANEOUS FORWARD CURRENT (A) 10 Tj = +175°C IR, INSTANTANEOUS REVERSE CURRENT (A) 100 1 Tj = +125°C 100n Tj = +25°C 100m 10n 10m Tj = +85°C 1m Tj = +25°C 1n Tj = -65°C Tj = -65°C 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 20 40 60 80 100 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 1 Typical Forward Characteristics IR, INSTANTANEOUS REVERSE CURRENT (A) 10m Tj = +175°C VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 2 Typical Reverse Characteristics 800 700 CT, TOTAL CAPACITANCE (pF) f = 1MHz 1m 600 500 400 300 200 100 0 Tj = +125°C Tj = +85°C 0 20 40 60 80 100 0 5 10 15 20 25 30 VR, INSTANTANEOUS REVERSE VOLTAGE (V) Fig. 3 Typical Reverse Characteristics VR, REVERSE VOLTAGE (V) Fig. 4 Typical Total Capacitance vs. Reverse Voltage DS30471 Rev. 18 - 2 PowerDI is a trademark of Diodes Incorporated. 2 of 4 www.diodes.com PDS5100H 7.5 IF, DC FORWARD CURRENT (A) 4 PF(AV), AVERAGE FORWARD POWER DISSIPATION (W) IPK = 1 (DC) IAV 6.0 3 4.5 Note 4 2 3.0 Note 2 1.5 1 0 0 25 50 75 100 125 150 175 TA, AMBIENT TEMPERATURE (°C) Fig. 5 DC Forward Current Derating 200 0 0 1 2 3 4 5 6 7 8 9 10 IF(AV), AVERAGE FORWARD CURRENT (A) Fig. 6 Forward Power Dissipation TA, DERATED AMBIENT TEMPERATURE (°C) 180 160 140 120 100 80 60 40 20 0 0 25 50 75 Note 2 100 VR, DC REVERSE VOLTAGE (V) Fig. 7 Operating Temperature Derating Ordering Information Device PDS5100H-13 Notes: 2. 3. 4. 5. 6. (Note 6) Packaging PowerDIä5 Shipping 5000/Tape & Reel FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. Short duration test pulse used to minimize self-heating effect. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf. Marking Information S5100H YYWWK S5100H = Product type marking code = Manufacturers’ code marking YYWW = Date code marking YY = Last two digits of year ex: 04 for 2004 WW = Week code 01 to 52 K = Factory Designator DS30471 Rev. 18 - 2 PowerDI is a trademark of Diodes Incorporated. 3 of 4 www.diodes.com PDS5100H IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. DS30471 Rev. 18 - 2 PowerDI is a trademark of Diodes Incorporated. 4 of 4 www.diodes.com PDS5100H