RS2D

RS2A/A - RS2M/A 1.5A SURFACE MOUNT FAST RECOVERY RECTIFIER Features · · · · · · Glass Passivated Die Construction Fast Recovery Time For High Efficiency Low Forward Voltage Drop and High Current Capability Surge Overload Rating to 50A Peak Ideally Suited for Automated Assembly Plastic Material: UL Flammability Classification Rating 94V-0 SMA SMB Min 3.30 4.06 1.96 0.15 5.00 0.10 0.76 2.00 Max 3.94 4.57 2.21 0.31 5.59 0.20 1.52 2.62 B Dim A B C D E G H Min 2.29 4.00 1.27 0.15 4.80 0.10 0.76 2.01 Max 2.92 4.60 1.63 0.31 5.59 0.20 1.52 2.62 A C Mechanical Data · · · · · · · Case: Molded Plastic Terminals: Solder Plated Terminal Solderable per MIL-STD-202, Method 208 Polarity: Cathode Band or Cathode Notch SMA Weight: 0.065 grams (approx.) SMB Weight: 0.09 grams (approx.) Mounting Position: Any Marking: Type Number J D H G E J All Dimensions in mm AA, BA, DA, GA, JA, KA, MA Suffix Designates SMA Package A, B, D, G, J, K Suffix Designates SMB Package Maximum Ratings and Electrical Characteristics Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current @ TT = 120°C Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load (JEDEC Method) Forward Voltage Peak Reverse Current at Rated DC Blocking Voltage Reverse Recovery Time (Note 3) Typical Junction Capacitance (Note 2) Typical Thermal Resistance, Junction to Terminal (Note 1) Operating and Storage Temperature Range @ IF = 1.5A @ TA = 25°C @ TA = 125°C Symbol VRRM VRWM VR VR(RMS) IO IFSM VFM IRM trr Cj RqJT Tj, TSTG RS2 A/AA 50 35 TA = 25°C unless otherwise specified RS2 B/BA 100 70 RS2 D/DA 200 140 RS2 G/GA 400 280 1.5 50 1.3 5.0 200 RS2 J/JA 600 420 RS2 K/KA 800 560 RS2 M/MA 1000 700 Unit V V A A V mA 150 30 20 -65 to +150 250 500 ns pF K/W °C Notes: 1. Thermal Resistance: Junction to terminal, unit mounted on PC board with 5.0 mm2 (0.013 mm thick) copper pads as heat sink. 2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC. 3. Reverse Recovery Test Conditions: IF = 0.5A, IR = 1.0A, Irr = 0.25A. See Figure 5. DS15004 Rev. E-2 1 of 2 RS2A/A - RS2M/A IF, INSTANTANEOUS FORWARD CURRENT (A) 1.5 10 IO, AVERAGE RECTIFIED CURRENT (A) 1.0 1.0 0.5 0.1 Tj = 25°C IF Pulse Width: 300 µs 0 25 50 75 100 125 150 175 0.01 0 0.4 0.8 1.2 1.6 TT, TERMINAL TEMPERATURE (°C) Fig. 1 Forward Current Derating Curve VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics IFSM, PEAK FORWARD SURGE CURRENT (A) IR, INSTANTANEOUS REVERSE CURRENT (µA) Single Half-Sine-Wave (JEDEC Method) 1000 Tj = 125°C 50 Tj = 150°C 100 40 30 10 20 1.0 Tj = 25°C 10 0 1 10 100 0.1 0 20 40 60 80 100 120 140 NUMBER OF CYCLES AT 60 Hz Fig. 3 Forward Surge Current Derating Curve PERCENT OF RATED PEAK REVERSE VOLTAGE (%) Fig. 4, Typical Reverse Characteristics trr +0.5A 50Ω NI (Non-inductive) Device Under Test 10Ω NI (-) Pulse Generator (Note 2) 0A (+) 50V DC Approx -0.25A (-) 1.0Ω NI Oscilloscope (Note 1) (+) Notes: 1. Rise Time = 7.0ns max. Input Impedance = 1.0MΩ, 22pF. 2. Rise Time = 10ns max. Input Impedance = 50Ω. -1.0A Set time base for 50/100 ns/cm Fig. 5 Reverse Recovery Time Characteristic and Test Circuit DS15004 Rev. E-2 2 of 2 RS2A/A - RS2M/A