SH10162.5P

CAPACITORS The ‘SH’ is a premium grade tantalum capacitor, exhibiting ultra-low leakagecurrent and impedance in small case sizes. Applications for this device include:High density logic boards Instrumentation Timing circuits Decoupling circuits - where space is a premium - requiring high temperature stability - requiring low leakage current - requiring low impedance TANTALUM DIPPED SH SECTION 1 Product is normally supplied loose on a 5mm pitch, but it is also available with a 2.5mm pitch and also taped & reeled for auto-insertion. All product is manufactured to comply with Dubilier’s stringent quality standards involving quality checks at each stage of processing and production. RANGE V µF 0.1 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 . øxl/mm 10 øxl/mm 1 øxl/mm 5 øxl/mm 5 øxl/mm 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.5 5.0x8.5 5.5x8.5 6.0x8.5 6.0x10.0 7.0x10.5 8.0x12.5 9.0x14.0 9.0x15.0 50 øxl/mm 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.0 5.0x8.5 5.0x9.0 5.5x8.5 6.0x10.0 6.5x10.0 7.0x10.5 8.0x13 8.5x14 9.0x14 SPECIFICATION Temperature Life Time Tolerance Leakage Current -55 to +85˚C (125˚C operation possible with de-rating) 2000 Hours @ +85°C ± 20% (10% available) 2 mins.) 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.5 5.0x8.5 5.0x9.0 5.5x8.5 6.0x10.0 6.5x10.0 7.0x10.5 8.0x12.5 9.0x14.0 10.0x17 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.5 5.0x8.5 5.0x9.0 5.5x8.5 6.0x9.0 6.5x10.0 7.0x10.5 8.0x12.5 9.0x14.5 10.0x17 10.0x18.5 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.5 5.0x8.5 5.0x9.0 5.5x8.5 6.0x10.0 6.0x10.0 8.0x12.0 9.0x12.0 9.0x16 9.0x16 10.0x18.5 4.5x7.0 4.5x7.0 4.5x7.0 4.5x7.5 5.0x8.5 5.0x9.0 5.5x9.0 6.0x10.0 7.0x10.5 8.0x12.0 9.0x14.0 9.0x16 All parts supplied with 5mm pitch as standard. 2.5mm pitch also available on parts with 7mm diameter or less. ORDERING INFORMATION SH Range 10 Capacitance µF 1 Voltage V TR Options: TR = Tape/Reel k = 10% Tol 2.5P : 2.5 pitch Blank = 5mm pitch 10 F ax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 CAPACITORS TANTALUM DIPPED SH ENDURANCE Test Time/Hr Leakage Current/µA Capacitance/µF Tan ∂ 2000 ± 48 Less than 125% of initial value Within ± 10% of initial value Less than or equal to initial value ELECTRICAL Stability at Temperature Extremes -55˚C Capacitance within ± 12% max (better than -5% typ) +85˚C Capacitance within ± 12% max (better than +5% typ). Leakage current within 10% initial value. Capacitance within 10% of initial value. Leakage current within 125% of initial value.Tan ∂ less than or equal to initial value. Capacitance within 10% of initial value. Leakage current within125% of initial value. Tan ∂ less than or equal to initial value. Capacitance within 5% of initial value. Leakage current less than or equal to initial value. Tan ∂ less than or equal to initial value. 6.3 10 16 25 35 50 8 13 20 32 44 63 6.3 10 16 25 35 50 4 6.3 10 16 23 33 SECTION 1 TAN ∂ Capacitance/µF Tan ∂ 0.1 to 1.5 0.04 2.2 to 6.8 0.06 10 to 68 0.08 100 to 220 0.1 Humidity 0˚C, 0-5% RH 1 days Shelf Life 000Hr @ 5˚C; no voltage applied Surge Voltage 1000 cycles @ 5˚C Rated Voltage/V Surge Voltage/V Temperature - Voltage de-rating @ 15˚C IMPEDANCE (ohms MAX.) V µF 0.1 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 . 10 1 5 5 26.0 21.0 17.0 15.0 13.0 10.0 8.0 6.0 5.0 4.0 3.0 2.5 2.0 1.6 1.3 1.0 0.8 50 26.0 21.0 17.0 15.0 13.0 10.0 8.0 5.0 3.5 3.0 2.5 2.0 1.6 1.2 1.0 13.0 10.0 8.0 6.0 5.0 3.7 3.0 2.0 1.8 1.6 0.9 0.9 0.7 13.0 10.0 8.0 6.0 5.0 3.7 2.7 2.1 1.7 1.3 1.0 0.8 0.6 0.5 10.0 8.0 6.0 5.0 4.0 3.2 2.5 2.0 1.6 1.3 1.0 0.8 0.6 0.5 10.0 8.0 6.0 5.0 4.0 3.1 2.5 2.0 1.5 1.2 1.0 0.8 Impedance measured at 100KHz and 25˚C. SAFETY Operating Properties It is recommended that the following operating modes are not imposed on the capacitors; Over or reverse voltage Over temperature Power rating exceeded High current surge due to low impedance (we recommend that the circuit impedance should be 3Ω/V minimum). 107 Material Content Tantalum capacitors contain no material normally considered as hazardous. Materials include: Epoxy Resin, Graphite, Manganese Dioxide, Tantalum, Tantalum Oxide. Noxious fumes may be emitted if incinerated. F ax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 CAPACITORS TANTALUM DIPPED SH OUTLINE DRAWING Capacitance Value Multiplier of DC Leakage Current Degrees – C ° SECTION 1 4 DIMENSIONS (mm) Code Po P S H Do W Description Feed hole pitch Hole centre to component centre Lead pitch Height to seating plane Feed hole diameter Tape width Dimensions/mm 12.7 ± 0.3 6.35 ± 0.4 5.0 + 0.8/-0.2 (2.5 + 0.4/-0.1 option) 16.0 ± 0.5 4.0 ± 0.2 18.0 + 1.0/-0.5 CHARACTERISTICS DC leakage current (DCL) increases with increasing temperature according to the typical curve Capacitance typically changes with temperature according to the curve +20 10.0 +10 0 -10 -20 -80 -60 -40 -20 0 +20 +40 +60 +80 +100 +120 Reference 1.0 at + 25 ˚C 1.0 Operating Temperature ˚C Optimum Solder Wave Profile Solder Wave Peak Temperature 260 °C Entrance to Solder Wave Exit from Solder Wave (Time in Wave – 2 to 4 Secs.) Hot Air Debridgin g Exit from Solder Machine 0.1 -60 -40 -20 0 +20 +40 +60 +80 +100 +125 Flux Zone Preheat Zone Operating Temperature –˚C 250 225 200 175 150 125 100 75 50 25 0 1 2 Top Side Nominal 3 Entrance to Solder Machine Typical Effect of Temperature upon DC Leakage Current 80 °C to 120 °C Bottom Side Temperature Range Free Free Air Air Cool Cool Entrance to In-Line Cleaner Exit from In-Line Cleaner (time in cleaner may be less) Immersion in Cleaning Vapor 150°C Max. 4 5 6 Time (Minutes) 10 F ax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758