SHJLC1025MXXXX

SURFACE MOUNT The SHJL surface mount products have inherently low ESR (equivalent series resistance) and is capable of higher ripple current, handling, producing lower ripple voltages, less power and heat dissipation than standard product for the most efficient use of circuit power, and has been particularly designed for typical power supply environments. TANTALUM CHIP - LOW ESR SHJL SECTION 1 SHJL SELECTION GUIDE Capacitance uF .V 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 10V 1V 0V 5V 5V C C C C C D C/D C/D/E D/E D/E D/E C/D C/D D D/E D/E E D D/E D/E D/E E D D/E D/E D/E E D/E D/E D/E E E D E E 50V D C/D D/E D/E D/E D/E SPECIFICATION Technical Data: Capacitance Range: Capacitance Tolerance: Environmental Classification: Dissipation Factor: All technical data relates to an ambient temperature of +25˚C 3.3µF to 470µF ±20%; ±10% 55/125/56 (IEC 68-2) ≤0.06 for E case for CR>10µF ≤0.08 for E case with CR≥100µF OUTLINE DRAWING W L H W1 A S A Code EIA Code L±0. W+0. H±0. W1±0. A±0. S Min. C 6032 6.0 3.2 2.6 2.2 1.3 2.9 D 7343 7.3 4.3 2.9 2.4 1.3 4.4 E 7343H 7.3 4.3 4.1 2.4 1.3 4.4 W1 dimension applies to the termination width for A dimensional area only. Pad Stand-off is 0.1±0.1. *A, B case available on request. ORDERING INFORMATION SHJL Range C Case size 10 µf value 5 Voltage K Tolerance K=10% M=20% XXXX ESR OHMIC value in mΩ 11 F ax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 SURFACE MOUNT RATINGS & PART NUMBER REFERENCE Dubilier Part No. SHJLC1006.3 SHJLD686.3 SHJLD1006.3 SHJLD1506.3 SHJLD2206.3 SHJLD3306.3 SHJLD4706.3 SHJLE1506.3 SHJLE2206.3 SHJLE3306.3 SHJLE4706.3 SHJLC1510 SHJLC2210 SHJLC6810 SHJLC10010 SHJLD4710 SHJLD6810 SHJLD10010 SHJLD15010 SHJLD22010 SHJLD33010 SHJLE10010 SHJLE15010 SHJLE22010 SHJLE33010 SHJLC3316 SHJLC4716 SHJLD3316 SHJLD4716 SHJLD6816 SHJLD10016 SHJLD15016 SHJLE10016 SHJLE15016 SHJLE22016 SHJLC1020 SHJLD2220 SHJLD3320 SHJLD4720 SHJLD6820 SHJLE3320 SHJLE4720 SHJLE6820 SHJLE10020 SHJLC4.725 SHJLD1525 SHJLD2225 SHJLD3325 SHJLD4725 SHJLE2225 Rated Voltage 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 10 10 10 10 10 10 10 10 10 10 10 10 16 16 16 16 16 16 16 16 16 16 20 20 20 20 20 20 20 20 20 25 25 25 25 25 25 Capacitance uF 100 68 100 150 220 330 470 150 220 330 470 15 22 68 100 47 68 100 150 220 330 100 150 220 330 33 47 33 47 68 100 150 100 150 220 10 22 33 47 68 33 47 68 100 4.7 15 22 33 47 22 Case Size C D D D D D D E E E E C C C C D D D D D D E E E E C C D D D D D E E E C D D D D E E E E C D D D D E DF Max 0.08 0.06 0.08 0.08 0.08 0.12 0.15 0.08 0.08 0.08 0.12 0.06 0.06 0.06 0.08 0.06 0.06 0.08 0.08 0.10 0.12 0.08 0.08 0.08 0.10 0.06 0.06 0.06 0.06 0.06 0.08 0.10 0.08 0.08 0.10 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.06 0.06 0.06 0.06 0.06 0.06 DCL Max 6.3 4.3 6.3 9.5 14.0 21.0 30.0 9.5 14.0 21.0 30.0 1.5 2.2 6.8 10.0 4.7 6.8 10.0 15.0 22.0 33.0 10.0 15.0 22.0 33.0 5.3 7.5 5.3 7.5 11.0 16.0 24.0 16.0 24.0 35.0 2.0 4.4 6.6 9.4 14.0 6.6 9.4 14.0 20.0 1.2 3.8 5.5 8.3 12.0 5.5 ESR Max MSL @100kHz 150 175 150 150 100 100 150 100 100 100 100 400 375 250 250 200 150 100 100 100 150 100 100 100 100 300 350 175 150 150 125 150 100 100 100 400 225 200 175 200 200 150 150 150 575 275 230 230 250 230 100kHz Ripple Current (mA) Rating 0.86 0.93 1.10 1.22 1.22 1.22 1.00 1.28 1.28 1.28 1.28 0.52 0.54 0.66 0.66 0.87 1.00 1.22 1.22 1.22 1.00 1.28 1.28 1.28 1.28 0.61 0.61 0.87 0.93 1.00 1.00 1.00 1.28 1.28 1.28 0.49 0.87 0.87 0.77 0.71 0.91 1.05 0.91 1.05 0.46 0.81 0.81 0.81 0.77 0.85 TANTALUM CHIP - LOW ESR SHJL SECTION 1 For 10% tolerance, insert ‘K’ in (*) above. For 20% tolerance, insert ‘M’ in (*) above. 11 F ax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758 SURFACE MOUNT TANTALUM CHIP - LOW ESR SHJL RATINGS & PART NUMBER REFERENCE CONT... SHJLC3.335 SHJLD6.835 SHJLD1035 SHJLD1535 SHJLE6.835 SHJLE1035 SHJLE1535 SHJLE2235 SHJLE3335 SHJLD4.750 SHJLE6.850 SHJLE1050 35 35 35 35 35 35 35 35 35 50 50 50 3.3 6.8 10 15 6.8 10 15 22 33 4.7 6.8 10 C D D D E E E E E D E E 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 1.2 2.4 3.5 5.3 2.4 3.5 5.3 7.7 12.0 2.4 3.4 5.0 550 400 260 300 300 260 225 275 260 300 300 300 0.45 0.71 0.76 0.76 0.74 0.80 0.80 0.80 0.80 0.71 0.74 0.74 SECTION 1 For 10% tolerance, insert ‘K’ in (*) above. For 20% tolerance, insert ‘M’ in (*) above. Note: Voltage ratings are minimum values. We reserve the right to supply higher voltage ratings in the same case size, to the same reliability standards. Other case size and ESR values available by request 11 F ax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758