D2E133-DM47-23

AC centrifugal fan D2E133-DM47-23 forward curved, dual inlet with housing (flange) ebm-papst Mulfingen GmbH & Co. KG Bachmühle 2 · D-74673 Mulfingen Phone +49 7938 81-0 Fax +49 7938 81-110 info1@de.ebmpapst.com www.ebmpapst.com Limited partnership · Headquarters Mulfingen County court Stuttgart · HRA 590344 General partner Elektrobau Mulfingen GmbH · Headquarters Mulfingen County court Stuttgart · HRB 590142 Nominal data Type D2E133-DM47-23 Motor M2E068-DF Phase 1~ 1~ Nominal voltage VAC 230 230 Frequency Hz 50 60 Type of data definition ml ml Valid for approval / standard CE CE Speed min-1 1650 2200 Power input W 175 185 Current draw A 0.78 0.82 Motor capacitor µF 3 3 Capacitor voltage VDB 450 450 Min. back pressure Pa 100 250 Min. ambient temperature °C -25 -25 Max. ambient temperature °C 40 40 ml = max. load · me = max. efficiency · fa = running at free air · cs = customer specs · cu = customer unit Subject to alterations Data according to ErP directive Actual Request 2013 Request 2015 Installation category A Overall efficiency ηes 25.5 25.3 32.3 Efficiency category Static Efficiency grade N 37.2 37 44 Variable speed drive No Power input Pe kW 0.14 Specific ratio* 1.00 Air flow qv m³/h 495 Pressure increase pfs Pa 270 Speed n min-1 2295 * Specific ratio = 1 + pfs / 100 000 Pa Data established at point of optimum efficiency Item no. 10985-5-9980 · Revision 71618 · Release 2010-08-03 · Page 1 / 5 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com AC centrifugal fan D2E133-DM47-23 forward curved, dual inlet with housing (flange) Technical features Mass 4. kg Size 133 mm Surface of rotor Partially cast in aluminium Material of impeller Sheet steel, hot-galvanised Housing material Sheet steel, hot-galvanised Motor suspension Motor mounted via brackets on one side Direction of rotation Clockwise, seen on rotor Type of protection IP 44; Depending on installation and position Insulation class "B" Humidity class F0 Max. permissible ambient motor temp. (transp./ storage) + 80 °C Min. permissible ambient motor temp. (transp./storage) - 40 °C Mounting position Any Condensate discharge holes None Operation mode S1 Motor bearing Ball bearing Touch current acc. IEC 60990 (measuring network Fig. 4, TN system) < 0.75 mA Motor protection Thermal overload protector (TOP) wired internally Cable exit Axial Protection class I (if protective earth is connected by customer) Product conforming to standard EN 60335-1; CE Approval CCC; GOST Item no. 10985-5-9980 · Revision 71618 · Release 2010-08-03 · Page 2 / 5 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com AC centrifugal fan D2E133-DM47-23 forward curved, dual inlet with housing (flange) Product drawing 1 Connection line PVC 0.5mm², 4x brass lead tips crimped Connection screen U1 blue PE green/yellow Z brown U2 black Item no. 10985-5-9980 · Revision 71618 · Release 2010-08-03 · Page 3 / 5 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com AC centrifugal fan D2E133-DM47-23 forward curved, dual inlet with housing (flange) Charts: Air flow 50 Hz Druck p f s[Pa]für Rho=1,2kg/m^3 460 0 50 100 150 qv[cfm] 250 300 200 350 400 450 500 440 420 400 380 360 4 340 320 300 3 280 p fs_E[IN H2O] pf s[Pa] 260 240 220 2 200 180 160 140 120 1 100 80 60 40 a] pf s[P 20 0 0 50 100 150 200 250 300 350 400 450 500 qv[m^3/h] 550 600 650 1,8 1,75 1,7 1,65 1,6 1,55 1,5 1,45 1,4 1,35 1,3 1,25 1,2 1,15 1,1 1,05 1 0,95 0,9 0,85 0,8 0,75 0,7 0,65 0,6 0,55 0,5 0,45 0,4 0,35 0,3 0,25 0,2 0,15 0,1 0,05 0 700 750 800 850 900 Measurement: LU-105266 Air performance measured as per ISO 5801 Installation category A. For detailed information on the measuring set-up, please contact ebm-papst. Suction-side noise levels: LwA measured as per ISO 13347 / LpA measured with 1m distance to fan axis. The values given are valid under the measuring conditions mentioned above and may vary according to the actual installation situation. With any deviation from the standard set-up, the specific values have to be checked and reviewed with the unit installed. Measured values U f n Pe I qv pfs V Hz min-1 W A m3/h Pa 1 230 50 1650 175 0.78 760 100 2 230 50 1990 162 0.70 640 200 3 230 50 2275 146 0.63 500 275 4 230 50 2530 125 0.54 240 350 U = Supply voltage · f = Frequency · n = Speed · Pe = Power input · I = Current draw · qv = Air flow · pfs = Pressure increase Item no. 10985-5-9980 · Revision 71618 · Release 2010-08-03 · Page 4 / 5 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com AC centrifugal fan D2E133-DM47-23 forward curved, dual inlet with housing (flange) Charts: Air flow 60 Hz Druck p f s[Pa]für Rho=1,2kg/m^3 0 50 100 150 200 qv[cfm] 250 300 350 400 450 500 2 480 1,9 460 1,8 440 1,7 420 4 400 1,6 380 1,5 360 3 1,4 340 1,3 320 2 1,2 pf s[Pa] 280 p fs_E[IN H2O] 300 1,1 260 1 1 240 220 0,9 200 0,8 180 Measurement: LU-105267 Air performance measured as per ISO 5801 Installation category A. For detailed information on the measuring set-up, please contact ebm-papst. Suction-side noise levels: LwA measured as per ISO 13347 / LpA measured with 1m distance to fan axis. The values given are valid under the measuring conditions mentioned above and may vary according to the actual installation situation. With any deviation from the standard set-up, the specific values have to be checked and reviewed with the unit installed. 0,7 160 0,6 140 120 0,5 100 0,4 80 0,3 60 0,2 40 ] [Pa pf s 20 0 0 50 100 150 200 250 300 350 400 450 qv[m^3/h] 500 550 600 650 700 750 800 0,1 0 Measured values U f n Pe I qv pfs V Hz min-1 W A m3/h Pa 1 230 60 2200 185 0.82 480 250 2 230 60 2360 181 0.78 400 300 3 230 60 2555 175 0.76 270 350 4 230 60 2685 171 0.74 170 400 U = Supply voltage · f = Frequency · n = Speed · Pe = Power input · I = Current draw · qv = Air flow · pfs = Pressure increase Item no. 10985-5-9980 · Revision 71618 · Release 2010-08-03 · Page 5 / 5 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com