E13C9D2K-155.520M

Marketing Bulletin DATE: TO: FROM: RE: March 24th, 2006 All Sales Personnel Mark Stoner Product Termination To all concerned parties, This bulletin is to notify all customers of the discontinuation of the following Ecliptek series effective March 24th, 2006: Series E13C9 Description 3.3V 5 x 7mm SMD LVPECL Oscillator Recommended Replacement E13C7 or E13D8 In compliance with our End of Life (EOL) policy, this will serve as advanced notice of product termination. New orders will not be accepted after July 1st, 2006, with delivery to conclude by October 1st 2006. If there are any questions pertaining to this bulletin, please fell free to contact me. Thank you again for your cooperation. Best Regards, Mark W. Stoner Director of Marketing Ecliptek Corporation 3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234 E13C9 Series • RoHS Compliant (Pb-Free) • LVPECL Output Oscillators • 3.3V Supply Voltage • AT-Cut Fundamental Mode Inverted Mesa Crystal • Ceramic 6-pad SMD Package • Stability to 25ppm • Tri-State Enable High and Enable Low Options Available on Pad 1 or Pad 2 • Complementary Output • Wide Range of Available Frequencies ELECTRICAL SPECIFICATIONS Nominal Frequency Operating Temperature Range Storage Temperature Range Supply Voltage (VCC) Input Current Frequency Tolerance / Stability H L W E13C9 2.0 7.0 5.0 OBSOLETE 19.440MHz to 200.000MHz 0°C to 70°C, or -40°C to +85°C -55°C to 125°C 3.3VDC ±5% 75mA Maximum ±100ppm, ±50ppm, or ±25ppm Maximum OSCILLATOR Inclusive of All Conditions: Calibration Tolerance at 25°C, Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change, 1st Year Aging at 25°C, Shock, and Vibration Output Voltage Logic High (VOH) Output Voltage Logic Low (VOL) Rise Time / Fall Time Duty Cycle Load Drive Capability Logic Control / Additional Output Enable High Tri-State Input Voltage 20% to 80% of waveform at 50% of waveform Enable Low Tri-State Input Voltage Enable High or Enable Low VIH of 70% of VCC Minimum No Connection VIL of 30% of VCC Maximum VIH of 70% of VCC Minimum No Connection VIL of 30% of VCC Maximum Output Disable Current Start Up Time RMS Phase Jitter Phase Noise (at 155.520MHz) < 44.736MHz; FJ = 12kHz to 20MHz > 44.736MHz, < 77.760MHz; FJ = 12kHz to 20MHz > 77.760MHz; FJ = 12kHz to 20MHz at 10Hz Offset at 100Hz Offset at 1kHz Offset at 10kHz Offset at 100kHz Offset SERIES PACKAGE VOLTAGE VCC-1.025VDC Minimum VCC-1.620VDC Maximum 1.5 nSeconds Maximum, 600 pSec Typical 50 ±10(%) 50 ±5(%) 50 Ohms into VCC-2.0VDC No Connect and Complementary Output or Tri-State and Complementary Output Enables Output Enables Output Disables Output: High Impedance Disables Output: High Impedance Enables Output Enables Output 25mA Maximum 10 mSeconds Maximum 5 pSec Maximum 2 pSec Maximum 1 pSec Maximum -75dBc/Hz Typical -95dBc/Hz Typical -125dBc/Hz Typical -140dBc/Hz Typical -145dBc/Hz Typical CLASS REV.DATE MANUFACTURER CATEGORY ECLIPTEK CORP. OSCILLATOR E13C9 CERAMIC 3.3V OS1T 06/04 800-ECLIPTEK www.ecliptek.com for latest revision Specifications subject to change without notice. OBSOLETE FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE C=±100ppm Maximum over 0°C to +70°C D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C G=±100ppm Maximum over -40°C to +85°C H=±50ppm Maximum over -40°C to +85°C J=±25ppm Maximum over -40°C to +85°C DUTY CYCLE 1=50% ±10%, 2=50% ±5% PART NUMBERING GUIDE E13C9 E 2 F - 155.520M TR AVAILABLE OPTIONS Blank=Tubes TR=Tape and Reel (Standard) FREQUENCY LOGIC CONTROL/ADDITIONAL OUTPUT C=No Connect and Complementary Output F=Tri-State (Enable High) on Pad 1 and Complementary Output H=Tri-State (Enable High) on Pad 2 and Complementary Output J=Tri-State (Enable Low) on Pad 1 and Complementary Output K=Tri-State (Enable Low) on Pad 2 and Complementary Output SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS MECHANICAL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS Pin 1: Tri-State or No Connect Pin 2: Tri-State or No Connect Pin 3: Case Ground Pin 4: Output Pin 5: Complementary Output Pin 6: Supply Voltage Tolerances= +0.1 TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE A 16±.3-.1 B 7.5±.1 C 6.75±.1 D 4 ±.1 E 2±.1 F REEL M 1.5 MIN N 50 MIN O 20.2 MIN P 13±.2 Q 40 MIN QTY/REEL 1,000 F 8±.1 G B0* H 1.5 +.1-0 J A0* K .3 ±.05 L K0* R 2.5 MIN S 10 MIN T 22.4 MAX U 360 MAX V 16.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Line 1: ECLIPTEK Characteristic Fine Leak Test Gross Leak Test Mechanical Shock Vibration Solderability Temperature Cycling Resistance to Soldering Heat Resistance to Solvents Specification MIL-STD-883, Method 1014, Condition A MIL-STD-883, Method 1014, Condition C MIL-STD-202, Method 213, Condition C MIL-STD-883, Method 2007, Condition A MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215 Line 2: XX.XXX M Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E13C9 CERAMIC 3.3V OS1T 06/04 800-ECLIPTEK www.ecliptek.com for latest revision Specifications subject to change without notice.