E31J2E3B2C-155.520MTR

Marketing Bulletin DATE: TO: FROM: RE: August 25, 2005 All Sales Personnel Mark Stoner Product Termination To all concerned parties, This bulletin is to notify all customers of the discontinuation of the following Ecliptek series effective August 25th, 2005: Series E31J2 E32J2 Description 5V 6 pad SMD LVPECL VCXO 3.3V 6 pad SMD LVPECL VCXO Recommended Replacement E32D1 E32D1 In compliance with our End of Life (EOL) policy, this will serve as advanced notice of product termination. New orders will not be accepted after November 25th, 2005, with delivery to conclude by February 25th 2006. If there are any questions pertaining to this bulletin, please fell free to contact me. Thank you again for your cooperation. Best Regards, Mark W. Stoner Director of Marketing Ecliptek Corporation 3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234 E31J2 Series • PECL Output VCXO • 5.0V supply voltage • 6 pad PCB SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel ELECTRICAL SPECIFICATIONS Frequency Range Operating Temperature Range Storage Temperature Range Supply Voltage (VCC) Input Current Logic Type Frequency Tolerance / Stability Output Voltage Logic High (VOH) Output Voltage Logic Low (VOL) Rise Time / Fall Time Duty Cycle Load Drive Capability Additional Output / Logic Control 20% to 80% of waveform at 50% of waveform Load, and Aging @25°C over 10 years E31J2 OBSOLETE H 5.9 L 14.8 W 10.2 OSCILLATOR 19.440MHz to 212.500MHz 0°C to 70°C or -40°C to 85°C -55°C to 125°C 5.0VDC ±5% 100mA Maximum 100KH Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or ±20ppm Maximum VCC-1.025VDC Minimum VCC-1.620VDC Maximum 2 nSeconds Maximum 50 ±10(%) 50 ±5(%) 50 Ohms into VCC-2.0VDC No Connect and Single Output Enable/Disable and Single Output No Connect and Complementary Output or Enable/Disable and Complementary Output Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum No Connection VIH of VCC-1.165VDC Minimum Enables Output Enables Output Disables Output: Logic Low Disables Complementary Output: Logic High 10 mSeconds Maximum Start Up Time RMS Phase Jitter Absolute Pull Range (APR) Linearity Control Voltage (VC): Test Conditions for APR Control Voltage Range (VCR) Center Control Voltage Transfer Function Input Impedance Modulation Bandwidth MANUFACTURER CATEGORY FJ = 12kHz to 20MHz Load, and Aging @25°C over 10 years 1 pSec Maximum Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum 20%, 15%, or 10% Maximum 2.5VDC ±2.0VDC 0.0VDC to VCC 2.5VDC Positive Transfer Characteristic 50kOhms Typical at -3dB with Control Voltage of +2.5VDC SERIES PACKAGE VOLTAGE 10kHz Minimum CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E31J2 6-PCB-J 5.0V OS74 01/03 800-ECLIPTEK www.ecliptek.com for latest revision 192 Specifications subject to change without notice. OBSOLETE FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C H=±50ppm Maximum over -40°C to +85°C APR 3=±50ppm Minimum LINEARITY A=20% B=15% C=10% MECHANICAL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS PART NUMBERING GUIDE E31J2 F 3 A 2 C - 155.520M TR AVAILABLE OPTIONS Blank=Tubes TR = Tape and Reel (Standard) FREQUENCY ADDITIONAL OUTPUT/LOGIC CONTROL A=No Connect and Single Output B=Enable/Disable and Single Output C=No Connect and Complementary Output D=Enable/Disable and Complementary Output DUTY CYCLE 1=50 ±10(%), 2=50 ±5(%) SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS TOP VIEW SIDE VIEW FRONT VIEW Pin 1: Voltage Control Pin 4: Output Pin 2: Enable/Disable or No Connect Pin 5: Complementary Output or No Connect Pin 3: Case Ground Pin 6: Supply Voltage TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS Tolerances = ±0.1 TAPE A 24 ±.3 B 11.5 ±.1 C 10.75 ±.1 D 4 ±.2 E 2±.1 F REEL M 1.5 MIN N 50 MIN O 20.2 MIN P 13±.2 Q 40 MIN QTY/REEL 1000 F 12 ±.1 G B0* H 1.5 +.1-0 J A0* K .4 ±.05 L K0* R 2.5 MIN S 10 MIN T 30.4 MAX U 360 MAX V 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Characteristic Seal Integrity Solderability Marking Permanency Shock Vibration Specification Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. 10 Strokes with brush after 1 minute soak in solvent, 3 times. Random drop on hard wooden plate 3 times from a height of 20cm. Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. CATEGORY SERIES PACKAGE Line 1: ECLIPTEK Line 2: XX.XXX M Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E31J2 6-PCB-J 5.0V OS74 01/03 800-ECLIPTEK www.ecliptek.com for latest revision 193 Specifications subject to change without notice. E32J2 Series • PECL Output VCXO • 3.3V supply voltage • 6 pad PCB SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel ELECTRICAL SPECIFICATIONS Frequency Range Operating Temperature Range Storage Temperature Range Supply Voltage (VCC) Input Current Logic Type Frequency Tolerance / Stability Output Voltage Logic High (VOH) Output Voltage Logic Low (VOL) Rise Time / Fall Time Duty Cycle Load Drive Capability Additional Output / Logic Control 20% to 80% of waveform at 50% of waveform Load, and Aging @25°C over 10 years E32J2 OBSOLETE H 5.9 L 14.8 W 10.2 OSCILLATOR 19.440MHz to 212.500MHz 0°C to 70°C or -40°C to 85°C -55°C to 125°C 3.3VDC ±5% 75mA Maximum 100KH Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or ±20ppm Maximum VCC-1.025VDC Minimum VCC-1.620VDC Maximum 2 nSeconds Maximum 50 ±10(%) 50 ±5(%) 50 Ohms into VCC-2.0VDC No Connect and Single Output Enable/Disable and Single Output No Connect and Complementary Output or Enable/Disable and Complementary Output Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum No Connection VIH of VCC-1.165VDC Minimum Enables Output Enables Output Disables Output: Logic Low Disables Complementary Output: Logic High 10 mSeconds Maximum Start Up Time RMS Phase Jitter Absolute Pull Range (APR) Linearity Control Voltage (VC): Test Conditions for APR Control Voltage Range (VCR) Center Control Voltage Transfer Function Input Impedance Modulation Bandwidth MANUFACTURER CATEGORY FJ = 12kHz to 20MHz Load, and Aging @25°C over 10 years 1 pSec Maximum Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum 20%, 15%, or 10% Maximum 1.65VDC ±1.35VDC 0.0VDC to VCC 1.65VDC Positive Transfer Characteristic 50kOhms Typical at -3dB with Control Voltage of +1.65VDC SERIES PACKAGE VOLTAGE 10kHz Minimum CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E32J2 6-PCB-J 3.3V OS73 01/03 800-ECLIPTEK www.ecliptek.com for latest revision 194 Specifications subject to change without notice. OBSOLETE FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C H=±50ppm Maximum over -40°C to +85°C APR 3=±50ppm Minimum LINEARITY A=20% B=15% C=10% MECHANICAL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS PART NUMBERING GUIDE E32J2 F 3 A 2 C - 155.520M TR AVAILABLE OPTIONS Blank=Tubes TR = Tape and Reel (Standard) FREQUENCY ADDITIONAL OUTPUT/LOGIC CONTROL A=No Connect and Single Output B=Enable/Disable and Single Output C=No Connect and Complementary Output D=Enable/Disable and Complementary Output DUTY CYCLE 1=50 ±10(%), 2=50 ±5(%) SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS TOP VIEW SIDE VIEW FRONT VIEW Pin 1: Voltage Control Pin 4: Output Pin 2: Enable/Disable or No Connect Pin 5: Complementary Output or No Connect Pin 3: Case Ground Pin 6: Supply Voltage TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS Tolerances = ±0.1 TAPE A 24 ±.3 B 11.5 ±.1 C 10.75 ±.1 D 4 ±.2 E 2±.1 F REEL M 1.5 MIN N 50 MIN O 20.2 MIN P 13±.2 Q 40 MIN QTY/REEL 1000 F 12 ±.1 G B0* H 1.5 +.1-0 J A0* K .4 ±.05 L K0* R 2.5 MIN S 10 MIN T 30.4 MAX U 360 MAX V 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Characteristic Seal Integrity Solderability Marking Permanency Shock Vibration Specification Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. 10 Strokes with brush after 1 minute soak in solvent, 3 times. Random drop on hard wooden plate 3 times from a height of 20cm. Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. CATEGORY SERIES PACKAGE Line 1: ECLIPTEK Line 2: XX.XXX M Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E32J2 6-PCB-J 3.3V OS73 01/03 800-ECLIPTEK www.ecliptek.com for latest revision 195 Specifications subject to change without notice.