KHP40

KHP KILOVOLT HIGH CURRENT RECTIFIER ASSEMBLIES RHP MATCHED SILICON RECTIFIER ELEMENTS RATED CURRENT TO 3.0 AMPERES PRV 5,000 TO 50,000 VOLTS FAST RECOVERY (RHP SERIES) ALL APPLICABLE MIL-STD-750 TESTS HIGH THERMAL CONDUCTIVITY ENCAPSULATION Peak ReverseVoltage PRV (Volts) 5,000 6,000 7,000 8,000 9,000 10,000 15,000 20,000 25,000 30,000 35,000 40,000 50,000 5,000 6,000 7,000 8,000 9,000 10,000 15,000 20,000 25,000 30,000 35,000 40,000 50,000 Avg. Fwd.Current IO at 25 oC (Am ps) 3.00 2.75 2.75 2.75 2.50 2.50 2.50 2.25 2.25 2.25 2.25 2.25 2.25 2.50 2.50 2.50 2.50 2.50 2.50 2.25 2.25 2.25 2.25 2.25 2.25 2.25 Max. Fwd Voltage Drop at 25 o C and 3 Amps V F (Volts) 8 9 10 11 14 15 21 28 36 42 49 63 70 10 11 12 13 16 17 25 33 42 50 58 65 82 Dim ens ion L Inches Fig .3 4.00 4.75 5.50 6.00 6.50 7.00 4.00 6.00 8.00 4.00 6.00 8.00 6.00 4.00 4.75 5.50 6.00 6.50 7.00 4.00 6.00 8.00 4.00 6.00 8.00 6.00 Dim ens ion W Inches Fig .3 1.0 1.0 1.0 1.0 1.0 1.0 2.0 2.0 2.0 3.0 3.0 3.0 4.0 1.0 1.0 1.0 1.0 1.0 1.0 2.0 2.0 2.0 3.0 3.0 3.0 4.0 EDI Type No. Case Sty le Fig .3 A A A A A A B B B B B B B A A A A A A B B B B B B B STANDARD RECOVERY KHP5 KHP6 KHP7 KHP8 KHP9 KHP10 KHP15 KHP20 KHP25 KHP30 KHP35 KHP40 KHP50 RHP5 RHP6 RHP7 RHP8 RHP9 RHP10 RHP15 RHP20 RHP25 RHP30 RHP35 RHP40 RHP50 200 NANOSECOND RECOVERY (FIG.4) ELECTRICAL CHARACTERISTICS (at TA =25 C Unless Otherwise Specified) o Max. DC Reverse Current @ PRV and 25 C, IR KHP SERIES STANDARD RECOVERY ELECTRICAL CHARACTERISTICS (at TA =25 C Unless Otherwise Specified) Max. DC Reverse Current @ PRV and 25 C, IR o RHP SERIES FAST RECOVERY 5 100 o A A o 5 A Max. DC Reverse Current @ PRV and 100 C, IR Ambient Operating Temperature Range,TA o Max. DC Reverse Current @ PRV and 100 C, IR o 250 A -55 C to +150 C -55 C to +150 C 400 Amps 40 Amps o o Max. Reverse Recovery Time , Trr (Fig.4) 200 nanosec -55 oC to +150 oC -55 oC to +150 oC 240 Amps 25 Amps Storage Temperature Range, TSTG Max.One-Half Cycle Surge Current, I FM (Surge )@ 60Hz Forward Current Repetitive Peak,I FRM Ambient Operating Temperature Range,TA Storage Temperature Range, TSTG Max.One-Half Cycle Surge Current, I FM (Surge )@ 60Hz Forward Current Repetitive Peak,I FRM E DI reserves the right to change these specifications at any time without notice. KHP FIG.1 OUTPUT CURRENT vs AMBIENT TEMPERATURE 100 400 RHP FIG.2 NON-REPETITIVE SURGE CURRENT IFSM. PEAK SURGE CURRENT (AMP) 300 240 200 150 100 70 50 % RATED FWD CURRENT 75 KHP 50 RHP 25 0 0 25 50 75 100 (O C) 30 20 125 150 AMBIENT TEMPERATURE 1 2 3 4 6 8 10 20 30 40 60 80 100 FIG.3 PACKAGE STYLE CASE STYLE A OUTLINE 3 8 NUMBER OF CYCLES(60 Hz) CASE STYLE B OUTLINE 8-32 THREAD X 1/4 DEEP (2) MTG. INSERTS L 1 MAX. L 1 W 1 4 6-32 THREAD X 1/4 DEEP (2) MTG. INSERTS 1 4 W 1 4 8-32 THREAD X 1/4 DEEP (4) MTG. INSERTS 1 4 1 4 It is recommended that a proper heat sink be used on the terminals of this device between the body and the soldering point to prevent damage form excess heat. TEST CIRCUIT FIG.4 TYPICAL REVERSE RECOVERY WAVEFORM T RR R1 50 OHM D.U.T. PULSE GENERATOR R2 1 OHM SCOPE + ZERO 0.5A REFERENCE 1.0A 0.25A R1, R2 NON-INDUCTIVE RESISTORS PULSE GENERATOR - HEWLETT PACKARD 214A OR EQUIV. IKC REP.RA TE, 10 SEC. PULSE WIDTH ADJUST PULSE AMPLITUDE FOR PEAK IR Prior to the manufacture of these assemblies, the individual silicon junction is measured for maximum recovery time in the test circuit shown. ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951. 21 GRAY OAKS AVENUE * YONKERS. NEW YORK 10710 914-965-4400 * FAX 914-965-5531 * 1-800-678-0828 E e-mail:sales@edidiodes.com * website:http:// www.edidiodes.com W