BA158BULK

www.eicsemi.com BA157 - BA159 FAST RECOVERY RECTIFIER DIODES PRV : 400 - 1000 Volts Io : 1.0 Ampere DO - 41 FEATURES : * * * * * * High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency 1.00 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) 0.205 (5.2) 0.166 (4.2) * Pb / RoHS Free MECHANICAL DATA : 1.00 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) * Case : DO-41 Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.34 gram Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL BA157 BA158 BA159 UNIT Maximum Recurrent Peak Reverse Voltage VRRM 400 600 1000 V Maximum RMS Voltage VRMS 280 420 700 V Maximum DC Blocking Voltage VDC 400 600 1000 V Maximum Average Forward Current 0.375"(9.5mm) Lead Length Ta = 45 °C IF(AV) 1.0 A IFSM 35 A VF 1.3 V IR 5.0 µA IR(H) 100 µA Peak Forward Surge Current, 8.3ms Single half sine wave Superimposed on rated load (JEDEC Method) Maximum Peak Forward Voltage at IF = 1.0 Amp. Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Maximum Reverse Recovery Time ( Note 1 ) Trr Typical Junction Capacitance ( Note 2 ) CJ 150 20 250 ns pf Junction Temperature Range TJ - 65 to + 150 °C Storage Temperature Range TSTG - 65 to + 150 °C Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC Page 1 of 2 Rev. 02 : March 24, 2005 www.eicsemi.com RATING AND CHARACTERISTIC CURVES ( BA157 - BA159 ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 A D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx.) 1Ω - 0.25 A OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50-100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 35 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 1.0 0.8 0.6 0.4 0.2 8.3 ms SINGLE HALF SINE WAVE 28 Ta = 50 °C 21 14 7 RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 0 175 1 2 AMBIENT TEMPERATURE, ( °C) 20 10 Pulse Width = 300 µs 2% Duty Cycle 1.0 TJ = 25 °C 0.1 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE, VOLTS Page 2 of 2 6 10 20 40 60 100 1.8 2.0 FIG.5 - TYPICAL REVERSE CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES FIG.4 - TYPICAL FORWARD CHARACTERISTICS 0 4 NUMBER OF CYCLES AT 60Hz 10 TJ = 100 °C 1.0 0.1 TJ = 25 °C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) Rev. 02 : March 24, 2005