FBR1510W

FBR1500W - FBR1510W PRV : 50 - 1000 Volts Io : 15 Amperes FEATURES : * * * * * * * High case dielectric strength High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Ideal for printed circuit board FAST RECOVERY BRIDGE RECTIFIERS BR50W 0.732 (18.6) 0.692 (17.5) 1.130 (28.7) 1.120 (28.4) 0.470 (11.9) 0.430 (10.9) * Pb / RoHS Free 0.21 (5.3) 0.20 (5.1) MECHANICAL DATA : * Case : Molded plastic with heatsink integrally mounted in the bridge encapsulation * Epoxy : UL94V-O rate flame retardant * Terminals : Plated lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer efficiency * Weight : 15.95 grams Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 0.042 (1.06) 0.038 (0.96) 1.2 (30.5) MIN. 0.310 (7.87) 0.280(7.11) Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS RATING Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Current Tc = 55 °C Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Current Squared Time at t < 8.3 ms. Maximum Forward Voltage drop per Diode at IF = 7.5 A Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance per diode (Note 2) Operating Junction Temperature Range Storage Temperature Range SYMBOL VRRM VRMS VDC IF(AV) IFSM It VF IR IR(H) Trr RθJC TJ TSTG 2 FBR 1500W FBR 1501W FBR 1502W FBR 1504W FBR 1506W FBR FBR 1508W 1510W 800 560 800 1000 700 1000 UNIT V V V A A AS V µA µA ns °C/W °C °C 2 50 35 50 100 70 100 200 140 200 400 280 400 15 300 375 1.3 10 200 600 420 600 150 1.9 250 - 50 to + 150 - 50 to + 150 500 Notes : 1 ) Measured with IF = 0.5 Amp., IR = 1 Amp., Irr = 0.25 Amp. 2 ) Thermal Resistance from junction to case with units mounted on a 3.2" x 3.2" x 0.12" THK (8.2cm.x 8.2cm.x 0.3cm.) Al. Plate. heatsink. Page 1 of 2 Rev. 02 : March 24, 2005 RATING AND CHARACTERISTIC CURVES ( FBR1500W - FBR1510W ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω + 0.5 D.U.T. 50 Vdc (approx) 1Ω PULSE GENERATOR ( NOTE 2 ) OSCILLOSCOPE ( NOTE 1 ) 0 - 0.25 Trr + - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. 1 FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT AVERAGE FORWARD OUTPUT CURRENT, AMPERES 15 300 FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES Tc = 55 °C 240 12 9 180 6 120 3 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 175 60 0 1 2 4 6 10 20 40 60 100 CASE TEMPERATURE, ( °C) FIG.4 - TYPICAL FORWARD CHARACTERISTICS PER DIODE 100 NUMBER OF CYCLES AT 60Hz FIG.5 - TYPICAL REVERSE CHARACTERISTICS PER DIODE REVERSE CURRENT, MICROAMPERES 10 TJ = 100 °C FORWARD CURRENT, AMPERES Pulse W idth = 300 µs 2% Duty Cycle TJ = 25 °C 10 1.0 1.0 0.1 TJ = 25 °C 0.1 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE, VOLTS Page 2 of 2 Rev. 02 : March 24, 2005