FBR3502W

FBR3500W - FBR3510W PRV : 50 - 1000 Volts Io : 35 Amperes FEATURES : * * * * * * High case dielectric strength High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency FAST RECOVERY BRIDGE RECTIFIERS BR50W 0.732 (18.6) 0.692 (17.5) 1.130 (28.7) 1.120 (28.4) 0.470 (11.9) 0.430 (10.9) * Pb / RoHS Free 0.21 (5.3) 0.20 (5.1) MECHANICAL DATA : * Case : Molded plastic with heatsink integrally mounted in the bridge encapsulation * Epoxy : UL94V-O rate flame retardant * Terminals : Plated lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer efficiency * Weight : 15.95 grams Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 0.042 (1.06) 0.038 (0.96) 1.2 (30.5) MIN. 0.310 (7.87) 0.280(7.11) Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS RATING Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Current Tc = 55 °C Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Current Squared Time at t < 8.3 ms. Maximum Forward Voltage drop per Diode at IF = 17.5 A Maximum DC Reverse Current at Rated DC Blocking Voltage Ta = 25 °C Ta = 100 °C SYMBOL V RRM V RMS V DC IF(AV) I FSM It VF IR I R(H) Trr R θJC TJ T STG 2 FBR FBR FBR FBR FBR FBR FBR 3500W 3501W 3502W 3504W 3506W 3508W 3510W UNIT V V V A A AS V µA µA 2 50 35 50 100 70 100 200 140 200 400 280 400 35 400 660 1.3 10 200 600 420 600 800 560 800 1000 700 1000 Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance per diode (Note 2) Operating Junction Temperature Range Storage Temperature Range 150 10 250 - 50 to + 150 - 50 to + 150 500 ns °C/W °C °C Notes : 1 ) Measured with IF = 0.5 A, IR = 1 A, Irr = 0.25 A 2 ) Thermal Resistance from junction to case with units mounted on a 7.5" x 3.5" x 4.6" (19cm.x 9cm.x 11.8cm.) Al.-Finned Plate Page 1 of 2 Rev. 02 : March 24, 2005 R ATING AND CHARACTERISTIC CURVES ( FBR3500W - FBR3510W ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω + 0.5 D.U.T. 50 Vdc (approx) 1Ω PULSE GENERATOR ( NOTE 2 ) OSCILLOSCOPE ( NOTE 1 ) 0 - 0.25 Trr + - 1.0 A S ET TIME BASE FOR 50/200 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. 1 FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT AVERAGE FORWARD OUTPUT CURRENT, AMPERES 35 400 FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES Tc = 55 °C 360 28 21 240 14 160 7 60Hz RESISTIVE OR INDUCTIVE LOAD 0 80 0 0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100 CASE TEMPERATURE, ( °C) FIG.4 - TYPICAL FORWARD CHARACTERISTICS REVERSE CURRENT, MICROAMPERES PER DIODE 100 NUMBER OF CYCLES AT 60Hz FIG.5 - TYPICAL REVERSE CHARACTERISTICS PER DIODE 10 TJ = 1 00 °C FORWARD CURRENT, AMPERES 10 1.0 1.0 0.1 TJ = 2 5 °C Pulse W idth = 300 µs 2% Duty Cycle 0.1 TJ = 2 5 °C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 F ORWARD VOLTAGE, VOLTS Page 2 of 2 R ev. 02 : March 24, 2005