FR102T/R

FR101 - FR107-STR FAST RECOVERY RECTIFIER DIODES PRV : 50 - 1000 Volts Io : 1.0 Ampere DO - 41 FEATURES : * * * * * * * High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Pb / RoHS Free 1.00 (25.4) MIN. 0.108 (2.74) 0.078 (1.99) 0.205 (5.20) 0.161 (4.10) 1.00 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) MECHANICAL DATA : * Case : DO-41 Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.34 gram Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL FR101 FR102 FR103 FR104 FR105 FR106 FR107 FR107 -STR UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 1000 V Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 700 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 1000 V Maximum Average Forward Current 0.375"(9.5mm) Lead Length Peak Forward Surge Current, Ta = 55 C 8.3ms Single half sine wave Superimposed IF(AV) 1.0 A IFSM 30 A VF 1.3 V IR 5 mA IR(H) 50 mA on rated load (JEDEC Method) Maximum Peak Forward Voltage at IF = 1.0 Amp. Maximum DC Reverse Current Ta = 25 C at Rated DC Blocking Voltage Ta = 100 C Maximum Reverse Recovery Time ( Note 1 ) Trr 150 250 500 250 ns Typical Junction Capacitance ( Note 2 ) CJ 50 pf Junction Temperature Range TJ - 65 to + 150 C Storage Temperature Range TSTG - 65 to + 150 C Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC Page 1 of 2 Rev. 03 : October 29, 2020 RATING AND CHARACTERISTIC CURVES ( FR101 - FR107-STR ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 W Trr 10 W + 0.5 A D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx ) 1W - 0.25 - 1.0 A OSCILLOSCOPE ( NOTE 1 ) SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 30 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 0.8 0.6 0.4 0.2 8.3 ms SINGLE HALF SINE WAVE Ta = 50 ฐC 24 18 12 6 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 0 25 50 75 100 125 150 175 1 AMBIENT TEMPERATURE, ( C) 2 4 6 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS 10 TJ = 100 ฐC Pulse Width = 300 ms 2% Duty Cycle REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES 20 10 TJ = 25 ฐC 1.0 0.1 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE, VOLTS Page 2 of 2 1.8 2.0 1.0 0.1 TJ = 25 ฐC 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) Rev. 03 : October 29, 2020