FR802

Certificate TH97/10561QM Certificate TW00/17276EM FR801 - FR805 PRV : 50 - 600 Volts Io : 8.0 Amperes FEATURES : * * * * * * * High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Pb / RoHS Free FAST RECOVERY RECTIFIER DIODES TO-220AC 0.154(3.91)DIA. 0.148(3.74) 0.415(10.54)MAX. 0.113(2.87) 0.103(2.62) 0.055(1.39) 0.045(1.14) 0.185(4.70) 0.175(4.44) 0.145(3.68) 0.135(3.43) 0.350(8.89) 0.330(8.39) 1 2 0.160(4.06) 0.140(3.56) 0.635(16.13) 0.625(15.87) 0.603(15.32) 0.573(14.55) PIN 1 CASE 0.560(14.22) 0.530(13.46) MECHANICAL DATA : * Case : Epoxy, Molded * Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds * Polarity: As marked * Mounting Position: Any * Weight : 2.24 grams (Approximately) PIN 2 0.205(520) 0.195(4.95) 0.037(0.94) 0.027(0.68) 0.022(0.56) 0.014(0.36) Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Current Half-Wave Resistive Load Peak Forward Surge Current 8.3ms Single half sine wave Superimposed on rated load (JEDEC Method) Maximum Peak Forward Voltage at I F = 8 A Maximum Reverse Current at Rated DC Blocking Voltage Tc = 25 °C Tc = 100 °C Tc = 100 °C SYMBOL FR801 FR802 FR803 FR804 FR805 VRRM VRMS VDC IF(AV) 50 35 50 100 70 100 200 140 200 8.0 400 280 400 600 420 600 UNIT V V V A IFSM VF IR IR(H) Trr CJ TJ, TSTG 150 150 1.3 10 150 250 70 - 65 to + 175 A V μA μA ns pF °C Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance( Note 2) Operating and Storage Temperature Range Notes : (1) Reverse Recovery Test Conditions : I F = 0.5 A, IR = 1.0 A, Irr = 0.25 A. (2) Measured at 1.0MHz and applied reverse voltage of 4.0V. Page 1 of 2 Rev. 02 : July 28, 2006 Certificate TH97/10561QM Certificate TW00/17276EM RATING AND CHARACTERISTIC CURVES ( FR801 - FR805 ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω + 0.5 A Trr + D.U.T. 50 Vdc (approx) 1Ω PULSE GENERATOR ( NOTE 2 ) OSCILLOSCOPE ( NOTE 1 ) 0 - 0.25 A - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. 1 cm FIG.2 - FORWARD CURRENT DERATING CURVE 10 150 FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) 8.3 ms Single Half Sine Wave JEDEC Method AVERAGE FORWARD CURRENT, (A) 8 120 6 90 4 60Hz Resistive load or Inductive load 60 2 30 0 0 25 50 75 100 125 150 175 0 1 2 4 6 10 20 40 60 100 CASE TEMPERATURE, ( °C) NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 10 FIG.5 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, ( μA) 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 10 1.0 1 0.1 0.1 0.01 0 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD VOLTAGE, (V) PERCENT OF RATED REVERSE VOLTAGE, (%) Page 2 of 2 Rev. 02 : July 28, 2006