SF165C

SF161C ~ SF166C PRV : 50 ~ 400 Volts Io : 16 Ampere FEATURES : * High current capability * High surge current capability * High reliability * Low reverse current * Low forward voltage drop * Super fast switching speed * Pb / RoHS Free PIN 3 SUPER FAST RECTIFIERS TO-220AB 0.154(3.91)DIA. 0.148(3.74) 0.113(2.87) 0.103(2.62) 0.415(10.54)MAX. 0.055(1.39) 0.045(1.14) 0.145(3.68) 0.135(3.43) 0.350(8.89) 0.330(8.39) 3 0.160(4.06) 0.140(3.56) PIN 2 CASE 0.205(520) 0.195(4.95) 0.037(0.94) 0.027(0.68) 0.105(2.67) 0.095(2.41) 0.022(0.56) 0.014(0.36) 0.560(14.22) 0.530(13.46) 0.185(4.70) 0.175(4.44) 0.635(16.13) 0.625(15.87) 2 12 PIN 1 0.603(15.32) 0.573(14.55) MECHANICAL DATA : * Case: Molded plastic * Epoxy: Device has UL flammability classification 94V-O * Lead: MIL-STD-202E method 208C guaranteed * Mounting position: Any * Weight : 2.24 grams (Approximately) Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING Maximum Repetitive Peak Reverse Voltage Maximum Working Reverse Voltage Maximum DC Blocking Voltage Maximum Average Forward Current Total Device,(Rated VR), Tc = 125°C Maximum Peak Rectified Forward Current 8.3 ms single half sine-wave, superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at IF = 8 A Maximum Reverse Current at Rated DC Blocking Voltage Typical Junction Capacitance (1) Maximum Reverse Recovery Time (2) Operating and Storage Temperature Range Notes : Tc = 25 °C Tc = 100 °C SYMBOL VRRM VRWM VDC IF(AV) SF161C SF162C SF163C SF164C SF165C SF166C UNIT V V V A 50 35 50 100 70 100 150 105 150 200 140 200 300 210 300 400 280 400 8.0 (Per Leg ) 16 (Total Device) IFSM VF IR IR(H) RθJC CJ Trr TJ, TSTG 50.0 35 1.0 150 1.35 10 500 3.0 30 50 - 65 to + 150 A V µA µA °C/W pF ns °C Typical Thermal Resistance, Junction to Case (1) Measured at 1 MHz and applied reverse voltage of 4.0 volts. (2) Reverse Recovery Test Conditions : IF = 0.5A, IR = 1A ; Irr = 0.25 A Page 1 of 2 Rev. 02 : March 31, 2005 RATING AND CHARACTERISTIC CURVES ( SF161C ~ SF166C ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω + 0.5 D.U.T. 50 Vdc (approx) 1Ω PULSE GENERATOR ( NOTE 2 ) OSCILLOSCOPE ( NOTE 1 ) 0 - 0.25 Trr + - 1.0 A SET TIME BASE FOR 15/25 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. 1 FIG. 2 - DERATING CURVE FOR OUTPUT CURRENT AVERAGE FORWARD SURGE CURRENT, (A) 20 FIG. 3 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 150 AVERAGE FORWARD OUTPUT CURRENT, AMPERES 16 120 8.3ms Single Half Sine-Wave (JEDEC Method) 12 90 8 Single Phase Half Wave 60Hz Inductive or Resistive Load 60 4 30 0 0 25 50 75 100 125 150 175 0 1 10 100 CASE TEMPERATURE, ( °C) FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 AVERAGE FORWARD CURRENT (AMPS) FIG. 5 -TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, AMPERES REVERSE CURRENT, MICROAMPERES Tc = 100 °C SF161C~SF164C 10 10 Tc = 25 °C 1 SF165C~SF166C 1.0 TJ = 25 °C 0.1 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 0.1 0 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE, VOLTS Page 2 of 2 Rev. 02 : March 31, 2005