HM5165405F

HM5164405F Series HM5165405F Series EO Description Features 64 M EDO DRAM (16-Mword × 4-bit) 8 k Refresh/4 k Refresh E0097H10 (1st edition) (Previous ADE-203-1056C (Z)) Jan. 31, 2001 The HM5164405F S erie s, HM5165405F S erie s ar e 64M-bit dynamic R AMs orga nized as 16, 777,216-w ord × 4-bit. The y have re alize d high per forma nce and low powe r by employing C MOS proc ess tec hnology. HM5164405F S erie s, HM5165405F S erie s off er Extende d Da ta Out (ED O) P age Mode as a high spee d ac ce ss mode. The y have the pac kage var iation of standa rd 32-pin plastic S OJ and standa rd 32-pin plastic TSOPII. • Single 3.3 V supply: 3.3 V ± 0.3 V • Access time: 50 ns/60 ns (max) • Power dissipation  Active: 396 mW/360 mW (max) (HM5164405F Series) : 468 mW/396 mW (max) (HM5165405F Series)  Standby : 1.8 mW (max) (CMOS interface) : 1.1 mW (max) (L-version) • EDO page mode capability • Refresh cycles  RAS -only refresh 8192 cycles /64 ms (HM5164405F, HM5164405FL) 4096 cycles /64 ms (HM5165405F, HM5165405FL)  CBR/Hidden refresh 4096 cycles /64 ms (HM5164405F, HM5164405FL, HM5165405F, HM5165405FL) Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd. L This product became EOL in December, 2006. Pr uc od t HM5164405F Series, HM5165405F Series • 4 variations of refresh  RAS -only refresh  CAS -before-RAS refresh  Hidden refresh  Self refresh (L-version) • Battery backup operation (L-version) EO Ordering Information Type No. HM5164405FJ-5 HM5164405FJ-6 HM5164405FLJ-5 HM5164405FLJ-6 HM5165405FJ-5 HM5165405FJ-6 HM5165405FLJ-5 HM5165405FLJ-6 HM5164405FTT-5 HM5164405FTT-6 HM5164405FLTT-5 HM5164405FLTT-6 HM5165405FTT-5 HM5165405FTT-6 HM5165405FLTT-5 HM5165405FLTT-6 2 Access time 50 ns 60 ns 50 ns 60 ns 50 ns 60 ns 50 ns 60 ns 50 ns 60 ns 50 ns 60 ns 50 ns 60 ns 50 ns 60 ns Package 400-mil 32-pin plastic SOJ (CP-32DC) L Data Sheet E0097H10 Pr 400-mil 32-pin plastic TSOP II (TTP-32DC) uc od t HM5164405F Series, HM5165405F Series Pin Arrangement (HM5164405F Series) EO VCC 1 2 3 4 5 6 7 8 9 I/O0 I/O1 NC NC NC NC WE RAS A0 A1 A2 A3 A4 A5 VCC 10 11 12 13 14 15 16 32-pin SOJ 32-pin TSOP 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 V SS I/O3 I/O2 NC NC NC VCC I/O0 I/O1 NC NC NC NC WE RAS A0 A1 A2 A3 A4 A5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 V SS I/O3 I/O2 NC NC NC CAS OE A12 A11 A10 A9 A8 A7 A6 V SS L OE A9 A8 A7 A6 (Top view) CAS A12 A11 A10 Pr V SS VCC (Top view) uc od t 3 Pin Description Pin name A0 to A12 Function Address input — Row/Refresh address A0 to A12 — Column address A0 to A10 Data input/output Row address strobe Column address strobe Write enable Output enable Power supply Ground No connection I/O0 to I/O3 RAS CAS WE OE VCC VSS NC Data Sheet E0097H10 HM5164405F Series, HM5165405F Series Pin Arrangement (HM5165405F Series) EO VCC 1 2 3 4 5 6 7 8 9 I/O0 I/O1 NC NC NC NC WE RAS A0 A1 A2 A3 A4 A5 VCC 10 11 12 13 14 15 16 32-pin SOJ 32-pin TSOP 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 V SS I/O3 I/O2 NC NC NC VCC I/O0 I/O1 NC NC NC NC WE RAS A0 A1 A2 A3 A4 A5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 V SS I/O3 I/O2 NC NC NC CAS OE NC A11 A10 A9 A8 A7 A6 V SS L OE NC A9 A8 A7 A6 (Top view) CAS A11 A10 Pr V SS VCC (Top view) uc od t Pin Description Pin name A0 to A11 Function Address input — Row/Refresh address A0 to A11 — Column address A0 to A11 Data input/output Row address strobe Column address strobe Write enable Output enable Power supply Ground No connection I/O0 to I/O3 RAS CAS WE OE VCC VSS NC Data Sheet E0097H10 4 HM5164405F Series, HM5165405F Series Block Diagram (HM5164405F Series) Row decoder EO A0 A1 to A10 Column buffers • • • address • • • Row address buffers A11 A12 RAS CAS WE OE Timing and control Column decoder L 16M array 16M array I/O buffers I/O0 to I/O3 Data Sheet E0097H10 5 Pr 16M array 16M array uc od t HM5164405F Series, HM5165405F Series Block Diagram (HM5165405F Series) Row decoder EO A0 A1 to A11 Column buffers • • • address • • • Row address buffers 6 RAS CAS WE OE Timing and control Column decoder L 16M array 16M array I/O buffers I/O0 to I/O3 Data Sheet E0097H10 Pr 16M array 16M array uc od t HM5164405F Series, HM5165405F Series Operation Table EO RAS H L L L CAS WE × × L L L L H L* L* × 2 2 OE × L × H L to H × × H I/O 0 to I/O 3 High-Z Dout Din Din Dout/Din High-Z High-Z High-Z Operation Standby Read cycle Early write cycle Delayed write cycle Read-modify-write cycle RAS -only refresh cycle CAS -before-RAS refresh cycle or Self refresh cycle (L-version) Read cycle (Output disabled) L L H to L H L H to L L H L H VT PT VCC VSS VIH VIL Ta L Notes: 1. H: VIH (inactive), L: VIL (active), ×: VIH or VIL 2. t WCS ≥ 0 ns: Early write cycle t WCS < 0 ns: Delayed write cycle Pr Symbol Value VCC –0.5 to +4.6 50 Iout 1.0 Tstg –55 to +125 Symbol Min Typ 3.0 0 3.3 0 2.0 — — –0.3 0 — Absolute Maximum Ratings Parameter Unit V V mA W Terminal voltage on any pin relative to VSS Power supply voltage relative to VSS Short circuit output current Power dissipation Storage temperature –0.5 to VCC + 0.5 (≤ 4.6 V (max)) uc od °C Max Unit Notes 3.6 V 1, 2 0 V 2 VCC + 0.3 0.8 70 V 1 V 1 ˚C DC Operating Conditions Parameter Supply voltage Input high voltage Input low voltage Ambient temperature range Notes: 1. All voltage referred to VSS . 2. The supply voltage with all VCC pins must be on the same level. The supply voltage with all VSS pins must be on the same level. t Data Sheet E0097H10 7 HM5164405F Series, HM5165405F Series DC Characteristics (HM5164405F Series) EO Parameter Operating current* * Standby current 1, 2 HM5164405F -5 Max 110 2 -6 Min — — Max 100 2 Unit mA mA Test conditions t RC = min TTL interface RAS , CAS = VIH Dout = High-Z CMOS interface RAS , CAS ≥ VCC – 0.2 V Dout = High-Z CMOS interface RAS , CAS ≥ VCC – 0.2 V Dout = High-Z t RC = min RAS = VIH, CAS = VIL Dout = enable t RC = min RAS = VIL , CAS cycle, t HPC = t HPC min CMOS interface Dout = High-Z CBR refresh: t RC = 15.6 µs t RAS ≤ 0.3 µs CMOS interface RAS , CAS ≤ 0.2 V Dout = High-Z Symbol Min I CC1 — — I CC2 — 0.5 — 0.5 mA L I CC2 — I CC3 I CC5 I CC6 I CC7 I CC10 — — — — — I CC11 — I LI I LO VOH VOL –5 –5 2.4 0 Standby current (L-version) 300 — 300 µA RAS -only refresh current* 2 Standby current* 1 110 5 110 110 1.2 — — — — — 100 5 100 100 1.2 mA mA mA mA mA Pr 500 — 500 5 5 VCC 0.4 –5 –5 5 5 2.4 0 VCC 0.4 CAS -before-RAS refresh current EDO page mode current* 1, * 3 Battery backup current* 4 (Standby with CBR refresh) (L-version) Self refresh mode current (L-version) Input leakage current Output leakage current Output high voltage Output low voltage Notes: 1. I CC depends on output load condition when the device is selected. I CC max is specified at the output open condition. 2. Address can be changed once or less while RAS = VIL. 3. Measured with one sequential address change per EDO cycle, t HPC . 4. VIH ≥ VCC – 0.2 V, 0 V ≤ VIL ≤ 0.2 V. Data Sheet E0097H10 8 uc od µA µA µA 0 V ≤ Vin ≤ VCC + 0.3 V 0 V ≤ Vout ≤ VCC Dout = disable V High Iout = –2 mA Low Iout = 2 mA V t HM5164405F Series, HM5165405F Series DC Characteristics (HM5165405F Series) EO Parameter Operating current* * Standby current 1, 2 HM5165405F -5 Max 130 2 -6 Min — — Max 110 2 Unit mA mA Test conditions t RC = min TTL interface RAS , CAS = VIH Dout = High-Z CMOS interface RAS , CAS ≥ VCC – 0.2 V Dout = High-Z CMOS interface RAS , CAS ≥ VCC – 0.2 V Dout = High-Z t RC = min RAS = VIH, CAS = VIL Dout = enable t RC = min RAS = VIL , CAS cycle, t HPC = t HPC min CMOS interface Dout = High-Z CBR refresh: t RC = 15.6 µs t RAS ≤ 0.3 µs CMOS interface RAS , CAS ≤ 0.2 V Dout = High-Z Symbol Min I CC1 — — I CC2 — 0.5 — 0.5 mA L I CC2 — I CC3 I CC5 I CC6 I CC7 I CC10 — — — — — I CC11 — I LI I LO VOH VOL –5 –5 2.4 0 Standby current (L-version) 300 — 300 µA RAS -only refresh current* 2 Standby current* 1 130 5 130 110 1.2 — — — — — 110 5 110 100 1.2 mA mA mA mA mA Pr 500 — 500 5 5 VCC 0.4 –5 –5 5 5 2.4 0 VCC 0.4 CAS -before-RAS refresh current EDO page mode current* 1, * 3 Battery backup current* 4 (Standby with CBR refresh) (L-version) Self refresh mode current (L-version) Input leakage current Output leakage current Output high voltage Output low voltage Notes: 1. I CC depends on output load condition when the device is selected. I CC max is specified at the output open condition. 2. Address can be changed once or less while RAS = VIL. 3. Measured with one sequential address change per EDO cycle, t HPC . 4. VIH ≥ VCC – 0.2 V, 0 V ≤ VIL ≤ 0.2 V. Data Sheet E0097H10 9 uc od µA µA µA 0 V ≤ Vin ≤ VCC + 0.3 V 0 V ≤ Vout ≤ VCC Dout = disable V High Iout = –2 mA Low Iout = 2 mA V t HM5164405F Series, HM5165405F Series Capacitance (Ta = 25˚C, VCC = 3.3 V ± 0.3 V) EO Parameter Input capacitance (Address) Input capacitance (Clocks) 10 Symbol CI1 CI2 CI/O Typ — — — Max 5 7 7 Unit pF pF pF Notes 1 1 1, 2 Output capacitance (Data-in, Data-out) Notes : 1. Capacitance measured with Boonton Meter or effective capacitance measuring method. 2. RAS and CAS = VIH to disable Dout. L Data Sheet E0097H10 Pr uc od t HM5164405F Series, HM5165405F Series AC Characteristics (Ta = 0 to +70˚C, VCC = 3.3 V ± 0.3 V, VSS = 0 V) *1, *2, *19 EO Test Conditions • • • • • Parameter Random read or write cycle time RAS precharge time CAS precharge time RAS pulse width CAS pulse width Row address setup time Row address hold time Column address setup time Column address hold time RAS to CAS delay time RAS hold time CAS hold time CAS to RAS precharge time OE to Din delay time OE delay time from Din CAS delay time from Din Transition time (rise and fall) Input rise and fall time: 2 ns Input pulse levels: VIL = 0 V, VIH = 3.0 V Input timing reference levels: 0.8 V, 2.0 V Output timing reference levels: 0.8 V, 2.0 V Output load: 1 TTL gate + C L (100 pF) (Including scope and jig) Read, Write, Read-Modify-Write and Refresh Cycles (Common parameters) RAS to column address delay time L Symbol t RC t RP t CP t RAS t CAS t ASR t RAH t ASC t CAH t RCD t RAD t RSH t CSH t CRP t OED t DZO t DZC tT HM5164405F/HM5165405F -5 Min 84 30 8 Max — — — -6 Min 104 40 10 Max — — — 10000 10000 — — — — Unit ns ns ns ns ns ns ns ns ns Notes Data Sheet E0097H10 11 Pr 50 8 0 8 0 8 12 10 13 38 5 13 0 0 2 10000 10000 — — — — 60 10 0 10 0 10 37 25 — — — — — — 14 12 15 40 5 15 0 0 50 2 uc od 45 30 ns ns 3 4 — — — — — — ns ns ns ns ns ns 5 6 6 50 ns 7 t HM5164405F Series, HM5165405F Series Read Cycle EO Parameter Access time from RAS Access time from CAS Access time from OE Access time from address Read command setup time Read command hold time to CAS Read command hold time to RAS Read command hold time from RAS Column address to RAS lead time Column address to CAS lead time CAS to output in low-Z Output data hold time Output data hold time from OE Output buffer turn-off time Output buffer turn-off to OE CAS to Din delay time Output data hold time from RAS Output buffer turn-off to RAS Output buffer turn-off to WE WE to Din delay time RAS to Din delay time 12 HM5164405F/HM5165405F -5 Symbol t RAC t CAC t AA t OEA t RCS t RCH Min — — — — 0 0 50 0 25 15 0 3 3 Max 50 13 25 13 — — — — — — — — — -6 Min — — — — 0 0 60 0 30 18 0 3 3 Max 60 15 30 15 — — — — — — — — — 15 15 — — Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 13, 21 13 5 21 21 12 12 Notes 8, 9 9, 10, 17 9, 11, 17 9 L t RCHR t RRH t RAL t CAL t CLZ t OH t OHO t OFF t OEZ t CDD t OHR t OFR t WEZ t WED t RDD Data Sheet E0097H10 Pr — — 13 13 — — — — 13 3 15 3 — — 13 13 13 13 — — — — 15 15 uc od 15 15 — — ns ns 13, 21 13 ns ns t HM5164405F Series, HM5165405F Series Write Cycle EO Parameter Write command setup time Write command hold time Write command pulse width Write command to RAS lead time Write command to CAS lead time Data-in setup time Data-in hold time HM5164405F/HM5165405F -5 Symbol t WCS t WCH t WP t RWL t CWL t DS Min 0 8 8 13 8 0 8 Max — — — — — — — -6 Min 0 10 10 15 10 0 10 Max — — — — — — — Unit ns ns ns ns ns ns ns 15 15 Notes 14 Read-Modify-Write Cycle L t DH Symbol t RWC t RWD t CWD t AWD t OEH Symbol t CSR t CHR t WRP t WRH t RPC Pr -5 -6 Min Max Min 116 67 30 42 13 — — — — — 140 79 34 49 15 -5 -6 Min 5 8 0 8 5 Max Min — — — — — 5 10 0 10 5 Data Sheet E0097H10 HM5164405F/HM5165405F Parameter Read-modify-write cycle time RAS to WE delay time CAS to WE delay time Column address to WE delay time OE hold time from WE Max — — — — — Unit ns ns ns ns ns Notes 14 14 14 uc od Max Unit Notes — — — — — ns ns ns ns ns Refresh Cycle HM5164405F/HM5165405F Parameter CAS setup time (CBR refresh cycle) CAS hold time (CBR refresh cycle) WE setup time (CBR refresh cycle) WE hold time (CBR refresh cycle) RAS precharge to CAS hold time t 13 HM5164405F Series, HM5165405F Series EDO Page Mode Cycle EO Parameter EDO page mode cycle time EDO page mode RAS pulse width Access time from CAS precharge CAS hold time referred OE CAS to OE setup time Read command hold time from CAS precharge OE precharge time Parameter HM5164405F/HM5165405F -5 Symbol t HPC t RASP t CPA t CPRH t DOH t COL Min 20 — — 28 3 8 5 28 8 8 Max — -6 Min 25 Max — Unit ns Notes 20 16 9, 17 100000 — 28 — — — — — — — — 35 3 10 5 35 10 10 100000 ns 35 — — — — — — — ns ns ns ns ns ns ns ns RAS hold time from CAS precharge Output data hold time from CAS low 9, 22 Write pulse width during CAS precharge t WPE t OEP EDO Page Mode Read-Modify-Write Cycle EDO page mode read-modify-write cycle time WE delay time from CAS precharge Refresh (HM5164405F Series) Parameter Refresh period Symbol t REF Refresh (HM5165405F Series) Parameter Refresh period Symbol t REF L t COP t RCHC Symbol t HPRWC t CPW Data Sheet E0097H10 14 Pr -5 -6 Min Max Min 57 45 — — 68 54 Max 64 Max 64 HM5164405F/HM5165405F Max Unit Notes uc od — — ns ns 14 Unit ms Notes 8192 cycles Unit ms Notes 4096 cycles t HM5164405F Series, HM5165405F Series Self Refresh Mode (L-version) EO Parameter RAS pulse width (self refresh) CAS hold time (self refresh) RAS precharge time (self refresh) HM5164405FL/HM5165405FL -5 Symbol t RASS t RPS t CHS Min 100 90 –50 Max — — — -6 Min 100 110 –50 Max — — — Unit µs ns ns Notes 25 25 Notes: 1. AC measurements assume t T = 2 ns. 2. An initial pause of 200 µs is required after power up followed by a minimum of eight initialization cycles (any combination of cycles containing RAS -only refresh or CAS -before-RAS refresh). 3. Operation with the t RCD (max) limit insures that t RAC (max) can be met, t RCD (max) is specified as a reference point only; if t RCD is greater than the specified t RCD (max) limit, than the access time is controlled exclusively by t CAC . 4. Operation with the t RAD (max) limit insures that t RAC (max) can be met, t RAD (max) is specified as a reference point only; if t RAD is greater than the specified t RAD (max) limit, then access time is controlled exclusively by t AA . 5. Either t OED or t CDD must be satisfied. 6. Either t DZO or t DZC must be satisfied. 7. VIH (min) and VIL (max) are reference levels for measuring timing of input signals. Also, transition times are measured between VIH (min) and VIL (max). 8. Assumes that t RCD ≤ t RCD (max) and t RAD ≤ t RAD (max). If t RCD or t RAD is greater than the maximum recommended value shown in this table, t RAC exceeds the value shown. 9. Measured with a load circuit equivalent to 1 TTL loads and 100 pF. 10. Assumes that t RCD ≥ t RCD (max) and t RCD + t CAC (max) ≥ t RAD + t AA (max). 11. Assumes that t RAD ≥ t RAD (max) and t RCD + t CAC (max) ≤ t RAD + t AA (max). 12. Either t RCH or t RRH must be satisfied for a read cycles. 13. t OFF (max), t OEZ (max), t WEZ (max) and t OFR (max) define the time at which the outputs achieve the open circuit condition and are not referred to output voltage levels. 14. t WCS , t RWD, t CWD, t AWD and t CPW are not restrictive operating parameters. They are included in the data sheet as electrical characteristics only; if t WCS ≥ t WCS (min), the cycle is an early write cycle and the data out pin will remain open circuit (high impedance) throughout the entire cycle; if t RWD ≥ t RWD (min), t CWD ≥ t CWD (min), and t AWD ≥ t AWD (min), or t CWD ≥ t CWD (min), t AWD ≥ t AWD (min) and t CPW ≥ t CPW (min), the cycle is a read-modify-write and the data output will contain data read from the selected cell; if neither of the above sets of conditions is satisfied, the condition of the data out (at access time) is indeterminate. 15. t DS and t DH are referred to CAS leading edge in early write cycles and to WE leading edge in delayed write or read-modify-write cycles. 16. t RASP defines RAS pulse width in EDO page mode cycles. 17. Access time is determined by the longest among t AA , t CAC and t CPA. 18. In delayed write or read-modify-write cycles, OE must disable output buffer prior to applying data to the device. 19. When output buffers are enabled once, sustain the low impedance state until valid data is obtained. When output buffer is turned on and off within a very short time, generally it causes large VCC/V SS line noise, which causes to degrade VIH min/VIL max level. L Data Sheet E0097H10 15 Pr uc od t HM5164405F Series, HM5165405F Series 20. t HPC (min) can be achieved during a series of EDO page mode write cycles or EDO page mode read cycles. If both write and read operation are mixed in a EDO page mode RAS cycle (EDO page mode mix cycle (1), (2)), minimum value of CAS cycle (tCAS + t CP + 2 t T) becomes greater than the specified t HPC (min) value. The value of CAS cycle time of mixed EDO page mode is shown in EDO page mode mix cycle (1) and (2). 21. Data output turns off and becomes high impedance from later rising edge of RAS and CAS . Hold time and turn off time are specified by the timing specifications of later rising edge of RAS and CAS between t OHR and t OH and between t OFR and t OFF. 22. t DOH defines the time at which the output level go cross. VOL = 0.8 V, VOH = 2.0 V of output timing reference level. 23. Before and after self refresh mode, execute CBR refresh to all refresh addresses in or within 64 ms period on the condition a and b below. a. Enter self refresh mode within 15.6 µs after either burst refresh or distributed refresh at equal interval to all refresh addresses are completed. b. Start burst refresh or distributed refresh at equal interval to all refresh addresses within 15.6µs after exiting from self refresh mode. 24. In case of entering from RAS -only-refresh, it is necessary to execute CBR refresh before and after self refresh mode according as note 23. 25 At t RASS > 100 µs, self refresh mode is activated, and not activated at t RASS < 10 µs. It is undefined within the range of 10 µs ≤ t RASS ≤ 100 µs. For t RASS ≥ 10 µs, it is necessary to satisfy t RPS. 26. XXX: H or L (H: VIH (min) ≤ VIN ≤ VIH (max), L: VIL (min) ≤ VIN ≤ VIL (max)) ///////: Invalid Dout When the address, clock and input pins are not described on timing waveforms, their pins must be applied VIH or VIL. EO 16 L Data Sheet E0097H10 Pr uc od t HM5164405F Series, HM5165405F Series Timing Waveforms*26 ; tDZO tOEA tOED OE tCAC tAA tRAC tCLZ tOEZ tOHO tOFF tOH tOFR tOHR tWEZ EO Read Cycle RAS tT CAS tASR tRAH Address Row WE Din Dout tRC tRAS tRP tCSH tRCD tRSH tCAS tCRP L tRAD tASC tRCS tDZC tRAL tCAL tCAH Data Sheet E0097H10 17 Pr Column tRCHR tRCH High-Z Dout tRRH uc od tCDD tWED tRDD t HM5164405F Series, HM5165405F Series Early Write Cycle EO RAS tT CAS tASR tRAH Address Row WE Din Dout 18 tRC tRAS tRP tCSH tRCD tRSH tCAS tCRP L tASC tCAH Data Sheet E0097H10 Pr Column tWCS tWCH uc od High-Z* * t WCS t WCS (min) tDS tDH Din t HM5164405F Series, HM5165405F Series Delayed Write Cycle*18 ; tDZO tOED tOEH tOEP OE tOEZ tCLZ Dout High-Z Invalid Dout Data Sheet E0097H10 EO RAS tT CAS tASR tRAH Address Row WE Din tRC tRAS tRP tCSH tRCD tRSH tCAS tCRP L tASC tRCS tDZC High-Z tCAH Column Pr tCWL tRWL tWP uc od tDS tDH Din t 19 HM5164405F Series, HM5165405F Series Read-Modify-Write Cycle*18 ; tDZO tOED tOEH tOEA tOEP OE tCAC tAA tOEZ tRAC tOHO Dout Dout High-Z tCLZ Data Sheet E0097H10 20 EO RAS tT CAS tASR tRAH Address Row WE Din tRWC tRAS tRP tRCD tCAS tCRP L tRAD tRCS tDZC tASC tCAH Column Pr tCWD tAWD tRWD tDS High-Z tCWL tRWL tWP uc od tDH Din t HM5164405F Series, HM5165405F Series RAS-Only Refresh Cycle ; EO RAS tRC tRAS tRP tT tRPC tCRP tCRP CAS L tASR tRAH Row tOFR Address Pr High-Z tOFF Dout Data Sheet E0097H10 21 uc od t HM5164405F Series, HM5165405F Series CAS-Before-RAS Refresh Cycle ; 22 EO tRP RAS tRPC tCP CAS WE Address tOFR tOFF Dout tRC tRAS tRP tRAS tRC tRP tT tRPC tCHR tCP tCSR tCHR tCRP tCSR L tWRP tWRH High-Z Data Sheet E0097H10 tWRP tWRH Pr uc od t HM5164405F Series, HM5165405F Series Hidden Refresh Cycle ; Dout Dout Data Sheet E0097H10 EO RAS tT tRCD tRC tRAS tRP tRC tRAS tRC tRP tRAS tRP tRSH tCHR tCRP CAS tASR L tRAD tRAL tRAH tASC tCAH Address Row Column Pr High-Z tOEA tCAC tAA tCLZ tRRH tRCH tRCS WE tDZC tWED tCDD tRDD uc od tOED tOFF tOEZ tWEZ tOHO tOH tOFR Din tDZO OE tRAC t 23 tOHR HM5164405F Series, HM5165405F Series EDO Page Mode Read Cycle (1) ; tWEZ tCAC tRAC tOEA tDOH tOHO tOEA Dout EO RAS t RP t RASP t CP t HPC t CAS t RCH t RCS t CP t HPC tCAS t RCHC t HPC t CPRH t CP t t CRP tT t CSH RSH CAS t CAS tCAS t RRH t RCH t RCS t RCHR WE tASR Address tRAH tASC Row tDZC L tCAH Column 1 t CAL High-Z tOEA tCAC tAA tCPA Dout 1 t WPE t ASC t CAH Column 2 t CAL t ASC t CAH Column 3 t CAL tASC t RAL t CAH Column 4 t WED t CAL tRDD tCDD Pr tCOL t OEP tAA tCAC tOEZ tOHO tCPA tAA tCAC Dout 2 Dout 2 Din tDZO tCOP tOED tOEP OE tCPA tAA tOEZ tOFR tOHR tOEZ tOHO tOFF tOH Data Sheet E0097H10 24 uc od Dout 3 Dout 4 t HM5164405F Series, HM5165405F Series EDO Page Mode Read Cycle (2) ; tOHO tOEZ tRAC tDOH tOEA tCAC tDOH tOHO tOEA Dout EO RAS t RP t RASP t HPC t CAS tHPC t CP t CAS t RCHC t CP t HPC tRSH tCAS t RRH t RCH t CRP tT t CSH t CP CAS t CAS t RCS WE tASR Address tRAH tASC Row tDZC L tCAH Column 1 t CAL High-Z tOEA tCAC tAA tCPA Dout 1 t ASC t CAH Column 2 t CAL t ASC t CAH Column 3 t CAL tASC t RAL t CAH Column 4 t WED t CAL tRDD tCDD Pr tCOL t OEP tAA tCAC tOEZ tCPA tAA tCAC Dout 2 Dout 2 Din tDZO tCOP tOED tOEP OE tCPA tAA tOFR tOHR tOEZ Data Sheet E0097H10 25 uc od tOHO tOFF tOH Dout 3 Dout 4 t HM5164405F Series, HM5165405F Series EDO Page Mode Early Write Cycle EO RAS tT tRCD CAS tASR tRAH Address Row WE Din Dout tRASP tRP tCSH tCAS tCP tHPC tCAS tCP tRSH tCAS tCRP L tASC tCAH Column 1 tWCS tWCH tDS tDH Din 1 tASC tCAH tASC tCAH Column 2 Column N Data Sheet E0097H10 26 Pr tWCS tWCH tDS tDH Din 2 High-Z* tWCS tWCH uc od tDS tDH Din N * t WCS t WCS (min) t HM5164405F Series, HM5165405F Series EDO Page Mode Delayed Write Cycle*18 ; OE tCLZ tCLZ tCLZ tOEZ tOEZ Dout Invalid Dout Invalid Dout Invalid Dout Data Sheet E0097H10 EO RAS tT tRCD CAS tRASP tRP tCP tCAS tHPC tCAS tCP tRSH tCAS tCRP tCSH L tRAD tRAH tASC tCAH Row Column 1 tCWL tRCS tRCS tWP tDZC tDS tDH Din 1 tDZO tOED tOEP tOEH tDZO tASR tASC tCAH Column 2 tCWL tASC tCAH Column N tCWL tRWL Address Pr tRCS tWP tDZC tDS tDH Din 2 tOED tOEP tOEH tDZO WE tWP tDZC tDS tDH uc od Din N tOED tOEP tOEH tOEZ High-Z Din t 27 HM5164405F Series, HM5165405F Series EDO Page Mode Read-Modify-Write Cycle*18 ; ; t AA t OEA t CAC t RAC t AA t CPA t OEA t CAC t AA t CPA t OEA t CAC t CLZ t OEZ t CLZ t OEZ t CLZ t OEZ High-Z EO RAS tT t RCD CAS t RASP t RP t HPRWC t CP t CAS t CAS t CP t RSH t CRP t CAS L t RAD t CAH Column 1 t ASR t ASC t RAH Row t ASC t CAH Column 2 t ASC t CAH Column N Address t RWD t AWD t CWD WE t RCS t WP t DS t DZC Pr t CWL t CPW t CWL t RCS t CPW t AWD t CWD t CWL t RWL t AWD t CWD t RCS t WP t DS t DZC t WP t DS t DZC uc od t DH t DH Din 2 Din N t DH Din t DZO t OED t OEP t OEH Din 1 t DZO t OED t OEP t OEH t DZO t OED t OEP t OEH OE t OHO t OHO t OHO Dout Dout 1 Dout 2 Dout N t Data Sheet E0097H10 28 HM5164405F Series, HM5165405F Series EDO Page Mode Mix Cycle (1)* 20 ; tOEP tWED OE EO RAS t RP t RASP t CRP tCAS tCWL t RCS tCPW tAWD tASC t CAH Column 3 t CAL tWP t RAL t CAH Column 4 t CAL t DS t DH tRDD tCDD t RCS tRSH t RRH t RCH tT t CP t CAS t CP tCAS t CP CAS t CAS t CSH t RCD t WCS t WCH L tCAH Column 1 t DH Din 1 WE tASR Address t ASC tRAH Row t ASC t CAH Column 2 tASC Pr High-Z tOED tCPA tAA tOEA tCPA tAA tCAC t DOH Dout 2 t DS Din Din 3 tCPA t OEZ tAA tOFR tWEZ tOEZ uc od tCAC tOHO tOFF tOH tCAC t OHO tOEA Dout 3 Dout Dout 4 t Data Sheet E0097H10 29 HM5164405F Series, HM5165405F Series EDO Page Mode Mix Cycle (2) *20 EO RAS t RP t RASP tT t CSH t CP t CAS t CP tCAS tCWL t RCS tCPW t ASC t CAH Column 3 t CP tCAS t RCS tWP t RAL tASC t CAH Column 4 t CAL t DS tRSH t CRP CAS t CAS t RCD t RCHR t RCS t RCH tWCS t WCH t RRH t RCH WE tASR Address t ASC tRAH Row L tCAH Column 1 t CAL t DS High-Z tOED tAA tOEA tCAC tOEZ t OHO Dout 1 t ASC t CAH Column 2 t DH t DH tRDD tCDD Pr Din 2 t OEP tOED tCOL t OEA tCPA tAA tCAC Din Din 3 t OEP tCOP tWED OE tCPA tOFR tWEZ tOEZ tOFF tOH uc od tOEZ tAA tCAC tOEA tOHO t OHO Dout 3 tRAC Dout Dout 4 t Data Sheet E0097H10 30 HM5164405F Series, HM5165405F Series Self Refresh Cycle (L-version)* 23, 24, 25 ; ; tRPC tCP tCSR CAS tWRP WE tOFR tOFF Dout ; High-Z Data Sheet E0097H10 EO tRP RAS tT tRASS tRPS tCRP tCHS L tWRH Pr uc od t 31 HM5164405F Series, HM5165405F Series Package Dimensions 10.16 ± 0.13 1 3.50 ± 0.26 1.165 Max 0.90 ± 0.26 *0.43 ± 0.10 0.41 ± 0.08 1.27 9.40 ± 0.25 0.10 *Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Weight (reference value) 2.55 ± 0.12 0.74 16 11.18 ± 0.13 EO 32 HM5164405FJ/FLJ Series HM5165405FJ/FLJ Series (CP-32DC) Unit: mm 20.95 21.38 Max 17 L 32 Data Sheet E0097H10 Pr CP-32DC — Conforms 1.2 g uc od t HM5164405F Series, HM5165405F Series HM5164405FTT/FLTT Series HM5165405FTT/FLTT Series (TTP-32DC) Unit: mm 0.10 *0.145 ± 0.05 0.125 ± 0.04 0.13 ± 0.05 1.20 Max *Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Weight (reference value) TTP-32DC Conforms — 0.51 g Data Sheet E0097H10 33 0.68 EO 20.95 21.35 Max 32 1 *0.42 ± 0.08 0.40 ± 0.06 0.21 1.15 Max 17 1.27 M 16 10.16 L 11.76 ± 0.20 0.80 Pr 0° – 5° 0.50 ± 0.10 uc od t HM5164405F Series, HM5165405F Series Cautions EO 34 1. Elpida Memory, Inc. neither warrants nor grants licenses of any rights of Elpida Memory, Inc.’s or any third party ’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Elpida Memory, Inc. bears no responsibility for problems that may arise with third party ’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability. However, contact Elpida Memory, Inc. before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Elpida Memory, Inc. particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Elpida Memory, Inc. bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so that the equipment incorporating Elpida Memory, Inc. product does not cause bodily injury, fire or other consequential damage due to operation of the Elpida Memory, Inc. product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Elpida Memory, Inc.. 7. Contact Elpida Memory, Inc. for any questions regarding this document or Elpida Memory, Inc. semiconductor products. L Data Sheet E0097H10 Pr uc od t