EM4095HMS

EM MICROELECTRONIC - MARIN SA EM4095 Read/Write analog front end for 125 kHz RFID Basestation Description The EM4095 (previously named P4095) chip is a CMOS integrated transceiver circuit intended for use in an RFID basestation to perform the following functions: -   Data transmission by Amplitude Modulation with externally adjustable modulation index using single ended driver Multiple transponder protocol compatibility (Ex: EM4102, EM4200, EM4450 and EM4205/EM4305) Sleep mode 1µA USB compatible power supply range -40 to +85°C temperature range Small outline plastic package SO16 antenna driving with carrier frequency AM modulation of the field for writable transponder AM demodulation of the antenna signal modulation induced by the transponder communicate with a microprocessor via simple interface.     Features  Integrated PLL system to achieve self adaptive carrier frequency to antenna resonant frequency  No external quartz required  100 to 150 kHz carrier frequency range  Direct antenna driving using bridge drivers  Data transmission by OOK (100% Amplitude Modulation) using bridge driver Applications Typical Operating Configuration Read Only Mode Pin Assignment  Car immobiliser  Hand held reader  Low cost reader RDY /CLK +5V LA CRES CDV1 +5V SO16 1 16 2 15 3 14 4 5 EM4095 P4095 13 12 6 11 7 10 8 9 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND P CDEC VSS RDY/CLK DC2 ANT1 SHD DVDD DEMOD_OUT DVSS MOD ANT2 AGND VDD CDV2 DEMOD_IN Fig. 1 FCAP CDEC_IN CDEC_OUT Fig. 3 Read/Write Mode RDY /CLK +5V LA CRES CDV1 +5V 1 16 2 15 3 14 4 5 EM4095 P4095 13 12 6 11 7 10 8 9 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND P CDEC CDV2 Fig. 2 Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 1 www.emmicroelectronic.com EM4095 System principle Transceiver R/W configuration Transponder RDY/CLK Coil1 Read Only and R/W Chip Coil2 +5V LA C RE S C DV +5V 1 1 16 2 15 3 14 4 5 EM4095 13 12 6 11 7 10 8 9 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND P CDEC C DV 2 DOWNLINK UPLINK Signal on Transponder coil Signal on Transceiver coil Signal on Transceiver coil Signal on Transponder coil RF Carrier RF Carrier Data Data Fig. 4 Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 2 www.emmicroelectronic.com EM4095 Absolute Maximum Ratings Parameter Storage temperature Maximum voltage at VDD Minimum voltage at VDD Max. voltage other pads Min. voltage other pads Max. junction temperature Electrostatic discharge max. to MIL-STD-883C method 3015 against VSS Electrostatic discharge max. to MIL-STD-883C method 3015 (only for pins ANT1 and ANT2) against VSS Maximum Input/Output current on all pads except VDD, VSS, DVDD, DVSS, ANT1, ANT2, RDY/CLK Maximum AC peak current on ANT1 and ANT2 pads 100 kHz duty cycle 50% Symbol Conditions TSTO -55 to +150°C VDDmax VSS+6V VDDmin VSS -0.3V VMAX VDD +0.3V VMIN VSS -0.3V TJMAX +125°C VESD 4000V VESD_ANT 8000V IIMAX IOMAX 10mA IANTmax 300mA Handling Procedures This device has built-in protection against high static voltages or electric fields; however, anti-static precautions must be taken as for any other CMOS component. Unless otherwise specified, proper operation can only occur when all terminal voltages are kept within the voltage range. Unused inputs must always be tied to a defined logic voltage level. Operating Conditions Parameter Operating junction temperature Supply voltage Antenna circuit resonant frequency AC peak current on ANT1 & ANT2 pads CFCAP CDEC CDC2 CAGND Package thermal resistor SO16 Symb TJ Min -40 Typ Max +110 Units °C VDD FRES 4.1 100 5 125 5.5 150 V kHz 250 mA * * * 220 71 nF nF nF nF °C/W IANT Rth j-a * * * 100 69 Stresses above these listed maximum ratings may cause permanent damages to the device. Exposure beyond specified operating conditions may affect device reliability or cause malfunction. * 10% tolerance capacitors should be used Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 3 10 100 6.80 70 ** According to 1S2P JEDEC test board Due to antenna driver current the internal junction temperature is higher than ambient temperature. Please calculate ambient temperature range from max. antenna current and package Thermal Resistor. It is the user's responsibility to guarantee that TJ remains below 110°C. Supply voltage (VDD and DVDD pads) must be blocked by a 100nF capacitor (to VSS) as close as possible to the chip www.emmicroelectronic.com EM4095 Electrical and Switching Characteristics: Parameters specified below are valid only in case the device is used according to Operating Conditions defined on previous page. VSS=DVSS=0V, VDD =DVDD = 5V, Tj = -40 to 110°C, unless otherwise specified Parameter Symbol Test Conditions Min Typ Max Units IDDsleep Supply current in sleep mode 1 2 µA IDDon Supply current excluding drivers 5 7 mA current VAGND AGND level Note 1 2.35 2.5 2.65 V Logic signals SHD, MOD, DEMOD_OUT VIH VIL VOH VOL RPD RPU Input logic high Input logic low Output logic high Output logic low MOD pull down resistor SHD pull up resistor 0.8VDD 0.1VDD 90 90 V V V V k k 150 150 kHz kHz 9 36   0.2VDD ISOURCE=1mA ISINK=1mA 0.2VDD 0.8VDD 0.9VDD 20 20 50 50 PLL Antenna capture frequency range Antenna locking frequency range FANT_C FANT_L 100 100 Drivers ANT drivers output resistance RDY/CLK driver output resistance RAD RCL IANT=100mA IRDY/CLK=10mA 3 12 AM demodulation VCM DEMOD_IN common mode range VSS + 0.5 VDD - 0.5 V DEMOD_IN input sensitivity Vsense Note 2 0.85 2 mVpp Note 1: AGND is a EM4095 internal reference point. Any external connection except specified capacitor to V SS may lead to device malfunction. Note 2: Modulating signal 2 kHz square wave on 125 kHz carrier, total signal inside VCM Vsense Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 4 www.emmicroelectronic.com EM4095 Timing Characteristics: Parameters specified below are valid only in case the device is used according to Operating Conditions defined on previous page. VSS=DVSS=0V, VDD=DVDD = 5V Parameter Symbol Test Conditions Typ Max Units Tset Set-up time after a sleep period 25 35 ms Tmdon Time from full power to modulation antenna circuit specifications: 50 µs Q=15,FRES=125Khz state modulation index: 100% AM demodulation: Delay time from Modulating signal 2Khz square Tpd 40 120 µs input to output wave 10mVpp Recovery time of reception after Trec Note 1 400 500 µs antenna modulation Note 1: RF period is time of one period transmitted on ANT outputs (at 125 kHz 8µs). Trec after antenna modulation receiver chain is ready to demodulate. The condition is of course that the amplitude on antenna has already reached its steady state by that time (this depends on Q of antenna). See also Application Notes. Block Diagram VDD VSS SHD AGND to all blocks to all blocks BIAS & AGND to all blocks BIAS & AGND to all blocks SHORT DETECTION & READY DVDD LOCK FCAP LOOP FILTER VCO & SEQUENCER ANTENNA DRIVERS HOLD MOD DMOD_IN RDY/CLK ANT1 ANT2 DVSS SY NCHRO SAMPLER CDEC_OUT FILTER CDEC_IN COMPARATOR DMOD_OUT DC2 Fig. 5 Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 5 www.emmicroelectronic.com EM4095 Functional Description General The EM4095 is intended to be used with an attached antenna circuit and a microcontroller. Few external components are needed to achieve DC and RF filtering, current sensing and power supply decoupling. A stabilised power supply has to be provided. Please refer to EM4095 Application Notes for advice. Device operation is controlled by logic inputs SHD and MOD. When SHD is high EM4095 is in sleep mode, current consumption is minimised. At power up the input SHD has to be high to enable correct initialisation. When SHD is low the circuit is enabled to emit RF field, it starts to demodulate any amplitude modulation (AM) signal seen on the antenna. This digital signal coming from the AM demodulation block is provided through DEMOD_OUT pin to the microcontroller for decoding and processing. High level on MOD pin forces in tri-state the main antenna drivers synchronously with the RF carrier. While MOD is high the VCO and AM demodulation chain are kept in state before the MOD went high. This ensures fast recovery after MOD is released. The switching ON of VCO and AM demodulation is delayed by 41 RF clocks after falling edge on MOD. In this way the VCO and AM demodulation operating points are not perturbed by start-up of antenna resonant circuit. Analog Blocks The circuit performs the two functions of an RFID basestation, namely: transmission and reception. Transmission involves antenna driving and AM modulation of the RF field. The antenna drivers deliver a current into the external antenna to generate the magnetic field. Reception involves the AM demodulation of the antenna signal modulation induced by the transponder. This is achieved by sensing the absorption modulation applied by the tag (transponder). Transmission Referring to the block diagram, transmission is achieved by a Phase Locked Loop (PLL) and the antenna drivers. Drivers The antenna drivers supply the reader basestation antenna with the appropriate energy. They deliver current at the resonant frequency which is typically 125 kHz. Current delivered by drivers depends on Q of external resonant circuit. It is strongly recommended that design of antenna circuit is done in a way that maximum peak current of 250 mA is never exceeded (see Typical Operating Configuration for antenna current calculation). Another limiting factor for antenna current is Thermal Convection of package. Maximum peak current should be designed in a way that internal junction temperature does not exceed maximum junction temperature at maximum application ambient temperature. 100% modulation (field stop) is done by switching OFF the drivers. The ANT drivers are protected against antenna DC short circuit to the power supplies. When a short circuit has been detected the RDY/CLK pin is pulled low while the main driver is forced in tri-state. The circuit can be restarted by activating the SHD pin. Phase locked loop The PLL is composed of the loop filter, the Voltage Controlled Oscillator (VCO), and the phase comparator blocks. By using an external capacitive divider, pin DEMOD_IN gets information about the actual high voltage signal on antenna. Phase of this signal is compared with the signal driving antenna drivers. Therefore the PLL is able to lock the carrier frequency to the resonant frequency of the antenna. Depending on the antenna type the resonant frequency of the system can be anywhere in the range from 100 kHz to 150 kHz. Wherever the resonant frequency is in this range it will be maintained by the Phase Lock Loop. Reception The demodulation input signal for the reception block is the voltage sensed on the antenna. DEMOD_IN pin is also used as input to Reception chain. The signal level on the DEMOD_IN input must be lower than VDD-0.5V and higher than VSS+0.5V. The input level is adjusted by the use of an external capacitive divider. Additional capacitance of divider must be compensated by accordingly smaller resonant capacitor. The AM demodulation scheme is based on the "AM Synchronous Demodulation" technique. The reception chain is composed of sample and hold, DC offset cancellation, bandpass filter and comparator. DC voltage of signal on DEMOD_IN is set to AGND by internal resistor. The AM signal is sampled, the sampling is synchronised by a clock from VCO. Any DC component is removed from this signal by the CDEC capacitor. Further filtering to remove the remaining carrier signal, high and low frequency noise is made by second order highpass filter and CDC2. The amplified and filtered receive signal is fed to asynchronous comparator. Comparator output is buffered on output pin DEMOD_OUT. Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 6 www.emmicroelectronic.com EM4095 Signal RDY/CLK This signal provides the external microprocessor with clock signal which is synchronous with the signal on ANT1 and with information about EM4095 internal state. Clock signal synchronous with ANT1 indicates that PLL is in lock and that Reception chain operation point is set. When SHD is high RDY/CLK pin is forced low. After high to low transition on SHD the PLL starts-up, and the reception chain is switched on. After time TSET the PLL is locked and reception chain operation point has been established. At this moment the same signal which is being transmitted to ANT1 is also put to RDY/CLK pin indicating to microprocessor that it can start observing signal on DEMOD_OUT and giving at the same time reference clock signal. Clock on RDY/CLK pin is continuous, it is also present during time the ANT drivers are OFF due to high level on MOD pin. During the time TSET from high to low transition on SHD pin RDY/CLK pin is pulled down by 100 k pull down resistor. The reason for this is in additional functionality of RDY/CLK pin in case of AM modulation with index which is lower then 100%. In that case it is used as auxiliary driver which maintains lower amplitude on coil during modulation. (see also Typical Operating Configuration) Read/Write mode (High Q factor antenna) RDY/CLK 1 16 RSER 2 15 3 14 +5V 4 13 LA CRES +5V CDV1 5 P4095 EM4095 12 6 11 7 10 8 9 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND P CDEC CDV2 Fig. 8 Read/Write mode (AM modulation) RDY/CLK RAM LA Remark: Please refer to AN4095 for external components calculation and limits. +5V Typical Operating Configuration 16 2 15 3 14 4 13 5 CRES CDV1 1 +5V EM4095 P4095 12 6 11 7 10 8 9 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND P CDEC CDV2 Read Only Mode Fig. 9 RDY/CLK 1 16 2 15 3 +5V LA CRES CDV1 +5V 4 5 14 P4095 EM4095 13 12 6 11 7 10 8 9 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND Figure 6 presents EM4095 used in Read Only mode. Pin MOD is not used. It is recommended to connect it to VSS. P Figure 7 presents typical R/W configuration for OOK communication protocol reader to transponder (eg. EM4450). It is recommended to be used with low Q factor antennas (up to 15). CDEC CDV2 Fig. 6 Read/Write mode (Low Q factor antenna) RDY/CLK +5V LA CRES CDV1 +5V 1 16 2 15 3 14 4 13 5 P4095 EM4095 12 6 11 7 10 8 9 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND P CDEC CDV2 Fig. 7 When the antenna quality is high using configuration of figure 6 or 7 the voltage on antenna can arrive in the range of few hundred volts and antenna peak current may exceed its maximum value. In such a case the capacitive divider ratio has to be high thus limiting the sensitivity. For such case it is better to reduce antenna circuit quality by adding serial resistor. In this way the antenna current is lower and thus power dissipation of IC is reduced with practically the same performance (Fig. 8). In the case AM modulation communication protocol reader to transponder (eg. EM4069) is needed a single ended configuration has to be used (figure 9). When pin MOD is pulled high driver on ANT1 is put in three state, driver RDY/CLK continues driving thus maintaining lower antenna current. Modulation index is adjusted by resistor RAM. As mentioned above RDY/CLK signal becomes active only after the demodulation chain operating point is set. Before it is pulled down by high impedance pull down resistor (100 k) in order not to load ANT1 output. In the case of AM modulation configuration the total antenna current change at the moment RDY/CLK pin becomes active, so external microprocessor has to wait another TSET before it can start observing DEMOD_OUT. Read Only mode with external peak detector Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 7 www.emmicroelectronic.com EM4095 RDY/CLK +5V LA CRES CDV1 +5V 1 16 2 15 3 14 4 13 5 EM4095 P4095 12 6 11 7 10 8 9 CDV2 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND P CDEC D1 C1 R1 Fig. 10 As mentioned above for high Q antennas the voltage on antenna is high and read sensitivity is limited by demodulator sensitivity due to capacitive divider. Read sensitivity (and thus reading range) can be increased by using external envelope detector circuit. Input is taken on antenna high voltage side output is directly fed to CDEC_IN pin. However, the capacitor divider is still needed for PLL locking. Such configuration is shown in Fig.10, the envelope detector is formed by three components: D1, R1 and C1. The configuration presented in figure 10 may also be used for read write applications but it has a drawback in the case fast recovery of reading is needed after communication reader to transponder is finished. The reason is in fact that DC voltage after diode D1 is lost during modulation and it takes very long time before it is established again. Read/Write mode with external peak detector Figure 11 presents a solution to that problem. A high voltage NMOS transistor blocks the discharge path during modulation, so operating point is preserved. The signal controlling NMOS gate has to be put low synchronously with signal MOD, but it can be put high only after the amplitude on antenna has recovered after modulation. RDY/CLK +5V LA CRES CDV1 CDV2 +5V 1 16 2 15 3 14 4 5 P4095 EM4095 13 12 6 11 7 10 8 9 CDC2 CFCAP SHD DEMOD_OUT MOD CAGND P PCB Layout Refer to "EM4095 Application Note" (App. Note 404) CDEC D1 C1 R1 Fig. 11 Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 8 www.emmicroelectronic.com EM4095 Pin Description SOIC 16 package Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 GND: IPD: Name Description VSS Negative power supply (substrate) RDY/CLK Ready flag and clock output, driver for AM modulation ANT1 Antenna driver DVDD Positive power supply for antenna drivers DVSS Negative power supply for antenna drivers ANT2 Antenna driver VDD Positive power supply DEMOD_IN Antenna sensing voltage CDEC_OUT DC blocking capacitor connection « out » CDEC_IN DC blocking capacitor connection « in » AGND Analog ground MOD A High level voltage modulates the antenna DEMOD_OUT Digital signal representing the AM seen on the antenna SHD A High level voltage forces the circuit into sleep mode FCAP PLL Loop filter capacitor DC2 DC decoupling capacitor reference ground PWR: power supply input with internal pull down IPU: input with internal pull up ANA: O: Type GND O O PWR GND O PWR ANA ANA ANA ANA IPD O IPU ANA ANA analog signal output Package and Ordering Information Dimensions of SOIC 16 Package (table in millimeters) Symbol A A1 B C D E H L Common Dimensions (mm) Min Nom Max 1.55 1.63 1.73 0.127 0.15 0.25 0.35 0.41 0.49 0.19 0.20 0.25 9.80 9.93 9.98 3.81 3.94 3.99 5.84 5.99 6.20 0.41 0.64 0.89 Fig. 12 Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 9 www.emmicroelectronic.com EM4095 Ordering Information EM4095 H M SO16 A + Bit-Coding RoHS Compliance H = AM + = Leadfree [blank] otherwise Cycle/bit n Delivery form M = Multi-Baud rate A = Stick B = Tape & reel Package SO16 = SOIC16 Product Support Check our Web Site under Products/RF Identification section. Questions can be sent to EMdirect@emmicroelectronic.com Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 10 www.emmicroelectronic.com EM4095 Appendix Equations Peak to peak voltage on antenna is defined by following equation: Antenna resonant frequency f0: 1 f0  2 LA C0 (1) Where C0 is resonant capacitor composed of CRES, CDV1 and CDV2: C0  CRES  CDV 1  CDV 2 CDV 1  CDV 2 2f 0 L A QA I ANT f 0 C 0 (6) To ensure correct operation of the AM demodulation chain, the AC peak to peak voltage on DEMOD_IN pin (VDMOD_INpp) has to be inside common mode range. Once peak to peak voltage on antenna is known the capacitor divider division factor can be calculated: (2) V DMOD _ INpp  V ANTpp Usually antenna coil is specified by its inductance (L A) and Q factor (QA). Serial resistance of antenna is defined by following equation: R ANT  V ANTpp  C DV 1 C DV 1  C DV 2 (7) Power dissipation is composed of power dissipated on ANT drivers and internal power consumption: P  2  I RMS  RAD  I DDon VDD  VSS  (3) 2 (7) The equations which follow are valid for bridge configuration as defined on Figures 1, 2 and 3. For figures 1 and 2 RSER has to be considered 0. Temperature increase of die due to power dissipation is: The AC current amplitude at resonant frequency is defined as follows: Where RTh is Package thermal resistor. I ANT  4  R ANT Vdd  Vss  RSER  2 R AD T  P  RTh (8) (4) RMS antenna current (important for power dissipation calculation): I RMS  I ANT 2 (5) EM Microelectronic-Marin SA (“EM”) makes no warranties for the use of EM products, other than those expressly contained in EM's applicable General Terms of Sale, located at http://www.emmicroelectronic.com. EM assumes no responsibility for any errors which may have crept into this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property rights of EM are granted in connection with the sale of EM products, neither expressly nor implicitly. In respect of the intended use of EM products by customer, customer is solely responsible for observing existing patents and other intellectual property rights of third parties and for obtaining, as the case may be, the necessary licenses. Important note: The use of EM products as components in medical devices and/or medical applications, including but not limited to, safety and life supporting systems, where malfunction of such EM products might result in damage to and/or injury or death of persons is expressly prohibited, as EM products are neither destined nor qualified for use as components in such medical devices and/or medical applications. The prohibited use of EM products in such medical devices and/or medical applications is exclusively at the risk of the customer. Copyright 2013, EM Microelectronic-Marin SA 4095-DS.doc, Version 4.2, 22-Apr-13 11 www.emmicroelectronic.com