LDO10C-005W05-HJ

Embedded Power for Business-Critical Continuity SXX06E Rev. 08.01.06 Page 1 of 2 LDO10C Series 50 Watts Total Power: 50 Watts Input Voltage: 3-13.8 Vdc No. of Outputs: Single Rev. 09.03.08 LDO10C 1 of 4 Electrical Specifications Output Output voltage Output setpoint accuracy Line regulation Load regulation Min./max. load Overshoot Undershoot Ripple and noise 5 Hz to 20 MHz Transient response At turn-on At turn-off See Note 1 See Notes 1, 2 See Note 5 0.1% trim resistors Low line to high line Full load to min. load 0.59-5.1 V ±1.0% ±0.2% ±0.5% 0 A/10 A 0.5% max. 100 mV max. 20 mV Vin=5 V, Vout=2.5 V 130 mV max. deviation 15 μs recovery to within regulation band 3-13.8 Vdc Minimum load Remote OFF See Note 3 Power up Remote ON/OFF Vin=5 V, Vo=2.5 V, lo=10 A Fixed 50 mA 5 mA 10 A @ lo max. 3 ms 2 ms 91% 620 kHz UL94V-0 1.899 g (0.067 oz.) 12 V @ 40 °C, 100% load Bellcore 332 Surface mount models 8,220,210 hours 150μm Special Features • 10 A output current rating • Input voltage range: 3-13.8 Vdc • Adjustable out voltage: 0.59-5.1 V • Factory set with power good option • Excellent transient response • Power enable • Minimum airflow • Small package • Termination voltage capability • RoHS compliant Input Input voltage range Input current Input current (max.) Start-up time General Efficiency Switching frequency Material flammability Weight MTBF Coplanarity Safety UL, cUL 60950-1 TÜV Product Service (EN60950) Certificate No. TBD CB Report and Certificate to IEC60950 Embedded Power for Business-Critical Continuity Environmental Specifications Thermal performance See Note 5 Operating ambient Non-operating ambient -40 °C to +85 °C -40 °C to +125 °C Hiccup, non-latching Hiccup, non-latching See Note 6 See Note 7 0 μF 0 μF Rev. 09.03.08 LDO10C 2 of 4 Protection Short-circuit Overvoltage protection Recommended System Capacitance Input Output Ordering Information Output Power (Max.) 50W 50W 50W Input Voltage 3-13.8 Vdc 3-13.8 Vdc 3-13.8 Vdc Output Voltage 0.59-5.1 V 0.59-5.1 V 0.59-5.1 V Output Current (Min.) 0A 0A 0A Output Current (Max.) 10 A 10 A 10 A Efficiency (Typical) 94% 94% 94% Regulation Line Load ±0.2% ±0.2% ±0.2% ±0.5% ±0.5% ±0.5% Model Number (3,5) LDO10C-005W05-VJ LDO10C-005W05-HJ LDO10C-005W05-SJ Part Number System with Options Product Family Rated Output Current Performance Input Voltage Number of Pins Type of Output Output Voltage Mounting Option Custom Option RoHS Compliance LDO Product Family LDO = LDO Series 10 Rated Output Current 10 = 10 Amp C Performance C = Cost Optimized 00 Input Voltage 00 = 3-13.8 V 01 = 4.5-13.8V 5W Type of Output 5W = 5 Pins and Wide Output 05 Output Voltage 05 = 0.59-5.1 V V Mounting Option V = Vertical H = Horizontal S = Horizontal SMT VS = Vertical SMT X Custom Option J RoHS Compliance J = Pb free (RoHS 6/6 compliant) Output Voltage Adjustment of the LDO10C Series The ultra-wide output voltage trim range offers major advantages to users who select the LDO10C series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.59-5.1 Vdc. When the LDO10C converter leaves the factory, the output has been adjusted to the default voltage of 0.59 V. Notes: 1. Measured as per recommended system capacitance. See Technical Reference Note. 2. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.50 lo to full lo and full lo to 0.50. 3. External input fusing is recommended. 4. Additional part numbers may be available with different output voltages. 5. Airflow dependent, 100 LFM minimum required. 6. No capacitors needed for ripple current stability. 7. No capacitors needed for stability. 8. TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please consult your local sales representative for details. 9. NOTICE: Some models do not support all options. Please contact your local Emerson Network Power representative or use the on-line model number search tool at http:// www.powerconversion.com/powergroup/products.htm to find a suitable alternative. Embedded Power for Business-Critical Continuity Mechanical Drawings Vertical Mount Dimensions in inches (mm). Tolerances es (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Rev. 09.03.08 LDO10C 3 of 4 0.410 (10.41) 0.45 (11.35) 0.055 (1.40) REF 0.062 (1.57) REF 0.650 (16.51) PIN 5 0.16 ± 0.010 (4 ± 0.25) 0.071 (1.80) 4X 0.067 TYP (1.70) PIN 1 0.050 (1.27) TYP 0.025 (0.64) ± .001 SQ PINS TYP Horizontal Mount 0.52 (13.13) 0.410 (10.41) 0.050 (1.27) PIN 6 0.650 (16.51) 0.062 (1.57) REF 0.125 (3.05) TYP 0.580 (14.73) 0.035 (0.89) 0.071 (1.80) PIN 5 Pin 1 0.055 (1.40) REF 0.025 (0.64)± .001 SQ PIN TYP 0.125 (3.18) TYP 4X 0.067 (1.70) TYP Embedded Power for Business-Critical Continuity SXX06E Rev. 08.01.06 Page 1 of 2 Mechanical Drawings (Cont'd) Surface Mount 0.52 (13.13) 0.410 (10.41) 0.062 (1.57) REF 7 0.650 (16.51) 6 Americas 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Rev. 09.03.08 LDO10C 4 of 4 Europe (UK) LDO10C005W05- Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 0.040 (1.02) REF 0.035 (0.89) REF 0 (0.00) 0.050 (1.27) 0.071 (1.80) 0.138 (3.51) 0.205 (5.21) 0.272 (6.91) 0.339 (8.61) 0.360 (9.14) 1 0.055 (1.40) REF 0.125 (3.18) TYP 0.025 (0.64) REF 5 Asia (HK) 16th - 17th Floors, Lu Plaza 2 Wing Yip Street, Kwun Tong Kowloon, Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.powerconversion.com For technical support, visit: http://www.powerconversion. com/support/product/ technical-support.php While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Pin Assignments Single Output 1. Enable 2. Vin 3. Common/RTN 4. Vout 5. PG/Trim 6. Mech Pin (Horz/SMT only) Connectivity DC Power Embedded Power Inbound Power Integrated Cabinet Solutions Outside Plant Precision Cooling Site Monitoring and Services EmersonNetworkPower. com *This is a Preliminary Datasheet. Emerson Network Power reserves the right to make changes to the information contained herein without notice and assumes no liability as a result of its use or application. Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co.