SIL10E-05W3V3-VJ

Embedded Power for Business-Critical Continuity SIL10E Series 3.0 Vin - 5.5 Vin Rev.3.4.09_96 SIL10E_05 Series 1 of 4 Total Power: 49.9 Watts Input Voltage: 3.0-5.5 Vdc # of Outputs: Single Electrical Specifications Special Features • 10 A Current rating • Input voltage range: 3 Vdc to 5.5 Vdc • Output voltage range: 0.8 Vdc to 3.63 Vdc • Ultra high efficiency: 96% @ 5 Vin and 3.3 Vout • Extremely low internal power dissipation • Minimal thermal design concerns • Designed in reliability: MTBF of 7,000,000 hours per Telcordia SR-332 • Ideal solution where board space is at a premium or tighter card pitch is required • Industry standard footprint and pin out • Available RoHS compliant • 2 year warranty Input Input voltage range: Input current: Input current (max.): Input reflected ripple: Remote ON/OFF: Start-up time: No load 3.0-5.5 Vdc 70 mA 8 A max. @ lo max. and Vout = 3.3 V 65 mA rms (See Note 2) 20 ms Fixed output versions 5 Vin with wide trim 3.3 Vin with wide trim ±10% 0.8 - 3.63 Vdc 0.8 - 2.75 Vdc ±0.4% typ. ±0.2% typ. ±1.0% typ. 0 A None 50 mV pk-pk 25 mV rms max. ±0.01%/˚C 50 mV max. deviation 50µs recovery to within ±1.0% 10% Vo compensation Output Voltage adjustability: (See Note 1) Setpoint accuracy: Line regulation: Load regulation: Minimum load: Overshoot/Undershoot: Ripple and noise: Temperature co-efficient: Transient response: Remote sense: Safety • UL/cUL CAN/CSA 22.2 No. 60950-1-03/UL 60950-1, File No. E186249 • TÜV Product Service (EN60950) Certificate No. B 08 05 51485 378 • CB report and certificate to IEC60950, Certificate No. DE3-51686M1 All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Embedded Power for Business-Critical Continuity Rev.3.4.09_96 SIL10E_05 Series  of 4 EMC Characteristics Electrostatic discharge: Conducted immunity: Radiated immunity: EN61000-4-2, IEC801-2 EN61000-4-6 EN61000-4-3 General Specifications Efficiency: Insulation voltage: Switching frequency: Approvals and standards: Material flammability: Dimensions Pin length: Weight: MTBF: Telcordia SR-332 MIL-HDBK-217F (L x W x H) (Vertical) Fixed See table Non-isolated 300 kHz typ. EN60950 UL/cUL60950 UL94V-0 50.8 x 7.8 x 12.7 mm 2.0 x 0.31 x 0.5 inches 0.135 ± 0.02 in (3.43 ± 0.5 mm) 5 g (0.18 oz) 7,042,000 hours 680,000 hours Environmental Specifications Thermal performance: (See Note 3) Operating ambient temperature Non-operating -40° C to +100 °C -40 °C to +125 °C Protection Short circuit: Thermal: Continuous Automatic recovery Embedded Power for Business-Critical Continuity Ordering Information All specifications are typical at nominal input, full load at 25 °C unless otherwise stated. Rev.3.4.09_96 SIL10E_05 Series 3 of 4 Ordering Information Output Power (Max.) 8.8 W 11 W 13.2 W 16.5 W 19.8 W 22 W 27.5 W 36.3 W 36.3 W Input Voltage 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 4.5 - 5.5 Vdc 4.5 - 5.5 Vdc Output Voltage 0.8 V 1 V 1.2 V 1.5 V 1.8 V 2 V 2.5 V 3.3 V 0.8 - 3.63 V Output Currents Min 0 A 0 A 0 A 0 A 0 A 0 A 0 A 0 A 0 A Max 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A Efficiency (typ.) 83% 86% 88% 90% 92% 93% 94% 95% 95% Regulation Line ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% ±0.2% Load ±1.5% ±1.5% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% Model Numbers (4, 5, 6) odel SIL10E-05S0V8-VJ SIL10E-05S1V0-VJ SIL10E-05S1V2-VJ SIL10E-05S1V5-VJ SIL10E-05S1V8-VJ SIL10E-05S2V0-VJ SIL10E-05S2V5-VJ SIL10E-05S3V3-VJ SIL10E-05W3V3-VJ Part Number System with Options SIL10E-05S3V3-VJ Packaging Options (5) J = Pb-free RoHS 6/6 compliant Mounting Options V = Vertical Mount H = Horizontal Mount Output Voltage 2.5 V, 3.3 V, etc Number of Outputs S = Single W = Wide Product Family SIL = Single In Line Rated Output Current 10 = 10 Amps Performance E = Enhanced Performance Input Voltage 05 = 3.0 V to 5.5 V 12 = 10 V to 14 V Output Voltage Adjustment of the SIL10E-05W3V3J Series The ultra-wide output voltage trim range offers major advantages to users who select the SIL10E-05W3V3J. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.8 Vdc to 3.63 Vdc. When the SIL10E-05W3V3J converter leaves the factory the output has been adjusted to the default voltage of 3.3 V. • When Vin ≥ 4.5 V, then Vout can be adjusted from 0.8 Vdc to 3.6 Vdc • When Vin < 4.5 V, then Vout can be adjusted from 0.8 Vdc to 2.75 Vdc Notes 1 When Vin ³ 4.5 V, then Vout can be adjusted from 0.8 V to 3.6 V. When Vin < 4.5 V, then Vout can be adjusted from 0.8 V to 2.75 V. 2 The SIL10E features a ‘Negative Logic’ Remote ON/OFF operation. If you are not using the Remote ON/OFF pin, leave the pin open (the converter will be on). The Remote ON/OFF pin is referenced to ground. The following conditions apply for the SIL10E: Configuration Remote pin open circuit Remote pin pulled low Remote pin pulled high [Von/off >1.2 V] Converter Operation Unit is ON Unit is ON Unit is OFF Notes Continued 3 Full derating curves available in both the Longform Datasheet and Application Note 136. 4 For certain applications that use low ESR capacitors on the output of the convertor and to insure maximum converter stability, please add the suffix ‘02’ to the model, e.g. SIL10E-05S2V5-V02J. 5 TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please contact your local sales representative for details. 6 NOTICE: Some models do not support all options. Please contact your local Emerson Network Power representative or use the on-line model number search tool at http://www.PowerConversion.com to find a suitable alternative. Embedded Power for Business-Critical Continuity Mechanical Drawings PIN VIEW 2.000 0.020 (50.80 0.50) SIDE VIEW PCB 0.500 (12.70) Americas Rev.3.4.09_96 SIL10E_05 Series 4 of 4 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) 0.025 0.001 (0.64 0.02) 6 5 J2 3 2 1 5 43 J1 2 1 0.316 0.008 (8.03 0.20) 0.170 (4.32) 0.100 (2.54) 1.900 (48.26) 0.050 (1.27) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) Dimensions in Inches (mm) Tolerances (unless other wise specified) 2 Place 0.15 3 Place 0.006 Figure 1: Horizontal Mount Version 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.PowerConversion.com SIDE VIEW 0.307 0.008 (7.80 0.20) PCB FRONT VIEW 2.000 0.020 (50.80 0.50) techsupport.embeddedpower @emerson.com 0.500 (12.70) While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. 0.135 (3.43) 0.635 (16.13) 1 2 3 J1 4 5 1 0.025 0.001 (0.64 0.02) 2 3 J2 5 6 Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power 0.168 (4.26) 0.100 (2.54) 0.050 (1.27) 1.900 (48.26) Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Place 0.15 3 Place 0.006 Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co. Figure 2: Vertical Mount Version Input Pin Connections J1 Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 +Vout +Vout Remote Sense (+) +Vout Ground Input Pin Connections J2 Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Ground +Vin +Vin No Pin Trim Remote ON/OFF