SIL40C2

Embedded Power for Business-Critical Continuity SXX06E Rev. 08.01.06 Page 1 of 2 SIL40C2 Series 4.5-13.8 Vin Single C-Class Non-Isolated 40 A Current Rating Input Voltage: 4.5-13.8 V No. of Outputs: Single Rev. 07.02.08 SIL40C2 1 of 5 Electrical Specifications Special Features • 40 A current rating • Input voltage range: 4.5-13.8 V • Output voltage: 0.6-5 V • Industry leading value • Cost optimized design • Excellent transient response • Output enable • Output voltage adjustability • Pathway for future upgrades • Supports silicon voltage migration • Resulting in reduced design-in and qual time • RoHS Compliant Output Output voltage Output setpoint accuracy Line regulation Load regulation Min./max. load Overshoot Undershoot Ripple and noise 5 Hz to 20 MHz Transient response At turn-on At turn-off See Note 1 See Notes 1, 2 See Note 5 0.1% trim resistors Low line to high line Full load to min. load 0.6-5 V ±1.0% ±0.2% ±0.5% 0 A/40 A 0.5% max. 100 mV max. 25 mV Vin=5 V, Vout=2.5 V 130 mV max. deviation 50 µs recovery to within regulation band 4.5-13.8 Vdc Minimum load Remote OFF See Note 3 Remote ON/OFF 50 mA 5 mA 25 A @ lo max. 3 ms Input Input voltage range Input current Input current (max.) Start-up time Safety UL, cUL CAN/CSA 22.2 No. E139421 UL6950 File No. TBD TÜV Product Service (EN60950) Certificate No. TBD CB report and certificate to IEC60950 Embedded Power for Business-Critical Continuity General Efficiency Switching frequency Approvals and standards (pending) Material flammability Weight MTBF 12 V @ 40 °C, 100% load Bellcore 332 Vin=5 V, Vo=2.5 V, lo=20 A Fixed 94% 500 kHz EN60950 UL/cUL6950 UL94V-0 17 g (0.06 oz.) 6,749,409 hours Rev. 07.02.08 SIL40C2 2 of 5 Coplanarity 150 µm Environmental Specifications Thermal performance See Note 5 Operating ambient, temperature Non-operating 0 °C to +70 °C -40 °C to +125 °C Hiccup, non-latching Hiccup, non-latching See Note 6 See Note 7 0 µF 0 µF Protection Short-circuit Overvoltage protection Recommended System Capacitance Input capacitance Output capacitance Ordering Information Output Power (Max.) 200 W 200 W 200 W Input Voltage 4.5-13.8 Vdc 4.5-13.8 Vdc 4.5-13.8 Vdc OVP N/A N/A N/A Output Voltage 0.6-5 Vdc 0.6-5 Vdc 0.6-5 Vdc Output Current (Min.) 0 A 0 A 0 A Output Current (Max.) 40 A 40 A 40 A Efficiency (Typical) 94% 94% 94% Regulation Line Load ±0.2% ±0.2% ±0.2% ±0.5% ±0.5% ±0.5% Model Number (3,5) SIL40C2-00SADJ-VJ SIL40C2-00SADJ-HJ SMT40C2-00SADJJ Embedded Power for Business-Critical Continuity Part Number System with Options Product Family Rated Output Current Performance Generation Input Voltage Output Voltage Mounting Option Rev. 07.02.08 SIL40C2 3 of 5 RoHS Compliance(8) SIL Product Family SIL = Single In Line SMT = Surface Mount 40 Rated Output Current 06 = 6 A 15 = 15 A 20 = 20 A 30 = 30 A 40 = 40 A C Performance C = Cost Optimized 2 Generation Blank = Standard Part 2 = Increased Current Density - 00 Input Voltage 00 = 4.5-13.8 V SADJ Output Voltage Single Adjustable Output - V Mounting Option V = Vertical H = Horizontal J RoHS Compliance J = Pb-free RoHS 6/6 Compliant Output Voltage Adjustment of the SIL40C2 Series The ultra-wide output voltage trim range offers major advantages to users who select the SIL40C2 series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.6-5 V. When the SIL40C2 converter leaves the factory, the output has been adjusted to the default voltage of 0.6 V. Standard Application Drawing Power Good Notes: 1 Measured as per recommended system capacitance. 2 di/dt = 10 A/µs, Vin = Nom, Tc = 25 °C, load change = 0.75 lo to full lo and full lo to 0.75. 3 External input fusing is recommended. 4 Additional part numbers may be available with different output voltages. 5 Airflow dependent, 100 LFM minimum required. 6 No capacitors needed for ripple current capability. 7 No capacitors needed for stability. 8 TSE RoHS 5/6 (non-Pb-free) compliant versions are also available on special request, please contact our local sales representative for details. 9 NOTICE: Some models may not support all options. Please contact your local representative or use the on-line model number search tool at http://www. powerconversion.com to find a suitable alternative. 10 To order a Horizontal Mounting option with a pin length of 0.165", please use the model # SIL40C2-00SA-HP5J Enable 6 5 SIL40C2 1,2,3 9 V out +R sense V in 10,11 7,8 C in R trim (for trim down) C out 4 R L O A D GND Figure 1: Standard Application Drawing Embedded Power for Business-Critical Continuity Rev. 07.02.08 SIL40C2 4 of 5 Mechanical Drawings Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Vertical Mount 1.200 (30.48) 0.427 (10.85) 1.100 (27.94) 0.050 (1.27) REF PIN 1 0.100 (2.54) 0.100 (2.54) TYP 9 PLACES 1.050 (26.67) 0.050 (1.27) TYP 0.025 (0.64) ±.001 SQ PINS TYP 0.140 (3.56) TYP 0.255 (6.48) 0.062 (1.57) REF 0.110 (2.79) Pin Assignments Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Function Vout Vout Vout Trim Enable Power Good Ground Ground (+) Sense Vin Vin *Mech support *Mech support Horizontal Mount Dimensions in Inches (mm) Tole0.468 (11.89) otherwise specified) rances (unless 2 Places ±0.030 (±0.76) 0.062 (1.57) REF 3 Places ±0.010 (±0.25) 1.200 (30.48) *Horizontal and SMT version only 0.255 (6.48) 1.100 (27.94) .150 (3.81) TYP PIN 1 0.110 (2.79) REF 2X 1.000 (25.40) 0.050 (1.27) REF 0.025 (0.64) ±.001 SQ PINS TYP 13 PLACES 0.100 (2.54) TYP 9 PLACES 2X 1.050 (26.67) 0.050 (1.27) 0.100 (2.54) REF Embedded Power for Business-Critical Continuity SXX06E Rev. 08.01.06 Page 1 of 2 Surface Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Americas 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 (760) 930 4600 Facsimile: +1 (760) 930 0698 Rev. 07.02.08 SIL40C2 5 of 5 0.062 (1.57) REF 0.125 (3.18) TYP 1.200 (30.48) 0.442 (11.23) 0.255 (6.48) 0.110 (2.79) REF Europe (UK) 1.100 (27.94) 2X 1.000 (25.40) 0.050 (1.27) REF PIN 1 0.100 (2.54) TYP 9 PLACES 0.050 (1.27) 0.100 (2.54) REF Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) Pin Assignments Pin No. Function 1 Vout 2 Vout 3 Vout 4 Trim Dimensions in nable 5 E Inches (mm) Tolerances (unless otherwise specified) 26 ±0.030 (±0.76) Places Power Good Places 37 ±0.010 (±0.25) Ground 8 Ground 9 (+) Sense 10 Vin 11 Vin 12 *Mech support 13 *Mech support *Horizontal and SMT version only 2X 1.050 (26.67) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.powerconversion.com techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower. com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co.