EM6353BX2SP3B-4.4

EM MICROELECTRONIC - MARIN SA Reset Circuit with Fixed Delay Description The EM6353 is an ultra-low current reset circuit available in a large variety of configurations and very small packages for maximum flexibility in all end-applications up to 125°C and using power supplies between 1.5V and 5.5V. This circuit monitors the supply voltage of any electronic system, and generates the appropriate reset signal after a fixed reset timeout period. The threshold defines the minimum allowed voltage which guarantees the good functionality of the system. When VDD rises above VTH, the output remains active for an additional delay time. This allows the system to stabilize before getting fully active. The EM6353 features three output types: active-low pushpull, active-low open-drain and active-high push-pull. Small SC70-5L and SOT23-3L packages as well as ultra-low supply current of 2.9µA make the EM6353 an ideal choice for portable and battery-operated devices. EM6353 Features ! ! ! ! ! ! 200ms reset timeout period (25ms on request) Ultra-low supply current of 2.9µA (VDD=3.3V) Operating temperature range: -40°C to +125°C ±1.5% reset threshold accuracy 11 reset threshold voltages VTH: 4.63V, 4.4V, 3.08V, 2.93V, 2.63V, 2.2V, 1.8V, 1.66V, 1.57V, 1.38V, 1.31V 3 reset output options: " Active-low RESET push-pull " Active-low RESET open-drain " Active-high RESET push-pull No external components Immune to short negative VDD transients Guaranteed Reset valid down to 0.8V Threshold hysteresis: 2.1% of VTH Very small SOT23-3L and SC70-5L packages ! ! ! ! ! Typical Application VDD VDD RESET * VDD RESET Applications ! ! ! ! ! ! ! ! 3 GND EM6353 GND MPU, DSP GND GND * REXT for open-drain version only Pin Configuration (top view) GND 1 3 RESET 2 (RESET) VDD VDD 2 RESET 1 (RESET) ! Mobile phones Set-top boxes Video, digital cameras, DVD players and recorders Modems Personal computers Switching hubs Copiers and fax Utility meters Automotive systems SOT23-3L "beta" bonding NC VDD NC 1 2 3 5 RESET (RESET) 4 GND SOT23-3L "alpha" bonding GND 4 RESET 5 (RESET) 3 NC 2 VDD 1 NC Block Diagram VDD Oscillator + Voltage Reference (compatible with SC70-3 by rotating 180°) SC70-5L - Reset Logic RESET RESET GND Pin Description Pin SOT23-3L “beta” 1 Function SC70-5L 4 SOT23-3L “alpha” 3 Name GND Ground Active-low RESET output. RESET remains low for the reset timeout period after all reset conditions are deasserted and then goes high. Active-high RESET output. RESET remains high for the reset timeout period after all reset conditions are deasserted and then goes low. Supply Voltage (5.5V max.) Not connected. Not internally connected. RESET 2 1 5 RESET 3 2 2 1,3 VDD N.C. Copyright © 2006, EM Microelectronic-Marin SA 03/06 – rev.K 1 www.emmicroelectronic.com EM6353 Ordering Information EM6353 B X 2SP3B - 2.9 + Delay (tPOR): B = 200ms A = 25ms Reset Output Type: X = Active-low /RES push-pull Y = Active-low /RES open-drain Z = Active-high RES push-pull Package & Bonding: 1SP3B = SOT23-3, "alpha", Tape&Reel 3kpcs 2SP3B = SOT23-3, "beta", Tape&Reel 3kpcs SC5B = SC70-5, Tape&Reel 3kpcs RoHS Compliance: + = lead-free/green mold compliant [blank] = leaded Reset Threshold Voltage (VTH): 1.3 = 1.31V 2.6 = 2.63V 1.4 = 1.38V 2.9 = 2.93V 1.6 = 1.57V 3.1 = 3.08V 1.7 = 1.66V 4.4 = 4.40V 1.8 = 1.80V 4.6 = 4.63V 2.2 = 2.20V Note: Subject to availability (see standard versions list below). Please give complete Part Number when ordering. All parts are offered in tape-and-reel only (3000 units). Standard Versions (Top Marking) Part Number EM6353BX1SP3B-1.3 EM6353BX1SP3B-2.6 EM6353BX1SP3B-2.6+ EM6353BX1SP3B-2.9 EM6353BX1SP3B-2.9+ EM6353BX1SP3B-4.4 EM6353BX1SP3B-4.4+ EM6353BX1SP3B-4.6 EM6353BX1SP3B-4.6+ EM6353BX2SP3B-1.3 EM6353BX2SP3B-1.8 EM6353BX2SP3B-1.8+ EM6353BX2SP3B-2.6 EM6353BX2SP3B-2.6+ EM6353BX2SP3B-2.9 EM6353BX2SP3B-2.9+ EM6353BX2SP3B-3.1 EM6353BX2SP3B-3.1+ EM6353BX2SP3B-4.4 EM6353BX2SP3B-4.4+ EM6353BX2SP3B-4.6 EM6353BX2SP3B-4.6+ EM6353BXSC5B-1.3 EM6353BXSC5B-1.8 EM6353BXSC5B-2.6 EM6353BXSC5B-2.6+ EM6353BXSC5B-2.9 EM6353BXSC5B-3.1 1) Top Marking Top Marking1) 2) with 4 Characters ALBA ALBG BLBG ALBH C1## BLBH ALBK C2## BLBK ALBL BLBL ALWA ALWE BLWE AW## ALWG BW## BLWG AR## ALWH BR## BLWH PC## ALWJ C5## BLWJ ALWK C8## BLWK ALWL BLWL ALWA ALWE AW## ALWG BW## BLWG AR## ALWH PC## ALWJ Part Number EM6353BXSC5B-3.1 EM6353BXSC5B-4.6 EM6353BY1SP3B-2.2 EM6353BY1SP3B-2.6 EM6353BY1SP3B-2.9 EM6353BY1SP3B-2.9+ EM6353BY1SP3B-3.1 EM6353BY1SP3B-4.4 EM6353BY1SP3B-4.6 EM6353BY2SP3B-2.6 EM6353BY2SP3B-2.6+ EM6353BY2SP3B-2.9 EM6353BY2SP3B-2.9+ EM6353BY2SP3B-3.1 EM6353BY2SP3B-3.1+ EM6353BY2SP3B-4.4 EM6353BY2SP3B-4.6 EM6353BY2SP3B-4.6+ EM6353BYSC5B-2.9 EM6353BYSC5B-2.9+ EM6353BYSC5B-4.4 EM6353BZ2SP3B-2.9 EM6353BZ2SP3B-2.9+ EM6353BZ2SP3B-3.1 EM6353BZ2SP3B-3.1+ EM6353BZ2SP3B-4.6 EM6353BZ2SP3B-4.6+ Top Marking Top Marking1) 2) with 4 Characters C5## BLWJ ALWL ALBS ALBT AS## ALBU BS## BLBU ALBV ALBW ALBX ALWT C9## BLWT ALWU C7## BLWU ALWV BLWV ALWW ALWX BLWX ALWU C7## BLWU ALWW AV## ALW6 BV## BLW6 ALW7 BLW7 ALW9 CB## BLW9 Top marking is the standard from 2006. No bottom marking exists. Where ## refers to the lot number (EM internal reference only) 2) Top marking with 4 characters is standard from 2003. For lead-free/green mold (RoHS) parts, the first letter of top marking with 4 characters begins with letter “B” instead of letter “A”. Bottom marking indicates the lot number. Copyright © 2006, EM Microelectronic-Marin SA 03/06 – rev.K 2 www.emmicroelectronic.com EM6353 Standard Versions (samples) Part Number EM6353BX1SP3B-2.6+ EM6353BX1SP3B-2.9+ EM6353BX1SP3B-4.4+ EM6353BX1SP3B-4.6+ EM6353BX2SP3B-1.8+ EM6353BX2SP3B-2.6+ EM6353BX2SP3B-2.9+ EM6353BX2SP3B-3.1+ EM6353BX2SP3B-4.4+ EM6353BX2SP3B-4.6+ Part Number EM6353BXSC5B-2.9 EM6353BXSC5B-3.1 EM6353BY1SP3B-2.9+ EM6353BY2SP3B-2.9+ EM6353BY2SP3B-3.1+ EM6353BY2SP3B-4.6+ EM6353BYSC5B-2.9+ EM6353BZ2SP3B-2.9+ EM6353BZ2SP3B-3.1+ EM6353BZ2SP3B-4.6 Sample stock is generally held on standard versions only. Non standard versions have a 30,000 pieces minimum order quantity. Please contact factory for other versions not shown here and for availability of non standard versions. Absolute Maximum Ratings Parameter Voltage at VDD to GND Minimum voltage at any signal pin Maximum voltage at any signal pin Handling Procedures Symbol VDD VMIN VMAX VESD TMAX TSTG Conditions -0.3V to +6V GND - 0.3V VDD + 0.3V 2000V 250°C x 10s -65°C to +150°C Electrostatic discharge max. to MIL-STD-883C method 3015.7 with ref. to VSS Max. soldering conditions Storage Temperature Range This device has built-in protection against high static voltages or electric fields; however, anti-static precautions must be taken as for any other CMOS component. Unless otherwise specified, proper operation can only occur when all terminal voltages are kept within the voltage range. Unused inputs must always be tied to a defined logic voltage level. Operating Conditions Parameter Supply voltage (note 1) Operating Temperature Symbol Min Max Unit VDD 0.8 5.5 V TA -40 +125 °C Stresses above these listed maximum ratings may cause permanent damage to the device. Exposure beyond specified operating conditions may affect device reliability or cause malfunction. Electrical Characteristics Unless otherwise specified: VDD= 0.8V to 5.5V, TA=-40°C to +125°C (note 1). Parameter Symbol Conditions VDD=1.5V Supply current (note 2) IDD VDD=3.3V VDD=5.0V Threshold voltage (note 3) VTH EM6353 – 1.3 +25°C -40°C to +125°C +25°C -40°C to +125°C +25°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C 3 Min 1.290 1.245 1.221 1.359 1.311 1.286 1.546 1.492 1.463 1.635 1.577 1.547 1.773 1.710 1.678 2.167 2.090 2.050 2.591 2.499 Typ 2.3 2.9 3.4 1.31 Max 4.6 7 5.5 8.3 6.3 9.6 1.330 1.382 1.387 1.401 1.456 1.461 1.594 1.656 1.663 1.685 1.751 1.758 1.827 1.899 1.906 2.233 2.321 2.330 2.669 2.775 Unit µA V EM6353 – 1.4 1.38 EM6353 – 1.6 1.57 EM6353 – 1.7 1.66 EM6353 – 1.8 1.80 EM6353 – 2.2 EM6353 – 2.6 Copyright © 2006, EM Microelectronic-Marin SA 03/06 – rev.K 2.20 2.63 www.emmicroelectronic.com EM6353 EM6353 – 2.9 -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C +25°C -40°C to +85°C -40°C to +125°C 2.451 2.886 2.784 2.731 3.034 2.926 2.871 4.334 4.180 4.101 4.561 4.399 4.315 2.93 2.785 2.974 3.091 3.103 3.126 3.249 3.262 4.466 4.642 4.660 4.699 4.885 4.903 V EM6353 – 3.1 3.08 EM6353 – 4.4 4.40 EM6353 – 4.6 Threshold hysteresis VHYS 4.63 2.1%•VTH TA=+25°C Note 1: Note 3: Production tested at +25°C only. Over temperature limits are guaranteed by design, not production tested. VDD min=0.9V for active-high versions (EM6353_Z). Threshold voltage is specified for VDD falling. Copyright © 2006, EM Microelectronic-Marin SA 03/06 – rev.K 4 www.emmicroelectronic.com EM6353 Electrical Characteristics Parameter Reset timeout period Propagation delay time VDD to RESET (RESET) delay Open-drain RESET output Voltage (continued) Unless otherwise specified: VDD= 0.8V to 5.5V, TA=-40°C to +125°C (note 1). Symbol tPOR tP Conditions VDD from 0V to VTH (typ)+15% (note 2 and 4). TA= +25°C EM6353B EM6353A Min 155 19.4 2 0.8 2 4 - Typ 200 25 130 - Max 224 28 255 0.3 0.3 0.3 0.3 0.3 0.35 0.5 Unit ms VDD drops from VTH (typ)+0.2V to VTH (typ)-0.2V (note 2). TA= +25°C VDD>1V IOL=100µA IOL=1.5mA IOL=3mA IOL=100µA IOL=1.5mA IOL=3mA IOH=-30µA IOH=-1.5mA IOH=-3mA VDD>2.5V VDD>5V VDD>1V µs VOL V VOL Push-pull RESET / RESET Output voltage VOH Output leakage current ILEAK VDD>2.5V VDD>5V VDD>1V VDD>2.5V VDD>5V V Only for EM6353_Y (open-drain) µA Note 1: Note 2: Note 4: Production tested at +25°C only. Over temperature limits are guaranteed by design, not production tested. VDD min=0.9V for active-high versions (EM6353_Z). RESET (RESET) open. Standard version is EM6353B (tPOR =200ms), available at all times. EM6353A (tPOR =25ms) is available by mask option and upon minimum order quantity. Please contact EM sales. Timing Waveforms tSEN VDD VTH Overdrive VHYS 0.8V t logic "1" RESET logic "0" t logic "1" tPOR tP RESET RESET logic "0" t Note 6: tSEN = Maximum Transient Duration. Please refer to figure on next page. Note 7: Overdrive = VTH- -VDD. Please refer to figure on next page. Copyright © 2006, EM Microelectronic-Marin SA 03/06 – rev.K 5 www.emmicroelectronic.com EM6353 Typical Operating Characteristics (Typical values are at TA=+25°C unless otherwise noted, RESET or RESET open.) 7 6 5 [ uA ] 4 3 2 1 0 -50 VDD 1. 5 V VDD 5 . 0 V VDD 3 . 3 V 300 250 200 [ us ] 150 100 50 0 -50 -25 -25 0 25 50 [ °C ] 75 100 125 0 25 50 75 100 125 [ °C ] IDD vs. Temperature Propagation Time tP vs. Temperature 200% 175% 150% 125% 100% 75% 50% 25% 0% -50 -25 0 25 50 75 100 125 [ °C ] tPOR (°C) tPOR (25°C) [ us ] 400 350 300 250 200 150 100 50 0 1 10 [ mV ] 100 1000 Reset occurs above this line Reset Timeout Period tPOR vs. Temperature (normalized with respect to tPOR 25°C) Maximum Transient Duration tSEN vs. Overdrive VTH-VDD 8% 6% 4% 2% 0% -2% -4% -6% -8% -50 -25 0 25 50 75 100 125 [°C] Threshold Voltage Variation vs. Temperature (normalized) Copyright © 2006, EM Microelectronic-Marin SA 03/06 – rev.K 6 www.emmicroelectronic.com EM6353 Package Information D A1 A2 A SOT23-3L E C L B H e SYMBOL A A1 A2 B C D E e e1 H L MIN 0.89 0.013 0.95 0.37 0.085 2.80 1.20 1.78 2.10 e1 TYP MAX 1.04 1.12 0.10 0.97 1.00 0.51 0.12 0.18 2.95 3.04 1.32 1.40 0.95 1.90 2.05 2.40 2.64 0.55 Dimensions are in mm D SC70-5L L HE E PIN 1 e e b Q1 c SYMBOL e D b E HE Q1 A2 A1 A c L MIN MAX 0.65 BSC 1.80 2.20 0.15 0.30 1.15 1.35 1.80 2.40 0.10 0.40 0.80 1.00 0.00 0.10 0.80 1.10 0.10 0.18 0.10 0.30 A2 A A1 NOTE: # All dimensions are in millimeters # Dimensions are inclusive of plating # Dimensions are exclusive of mold flash & metal burr # All specifications comply to EIAJ SC70 Traceability for small packages Due to the limited space on the package surface, the bottom marking contains a limited number of characters that provide only partial information for lot traceability. Full information for complete traceability is however provided on the packing labels of the product at delivery from EM. It is highly recommended that the customer insures full lot traceability of EM product in his final product. EM Microelectronic-Marin SA (EM) makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in EM's General Terms of Sale located on the Company's web site. EM assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of EM are granted in connection with the sale of EM products, expressly or by implications. EM's products are not authorized for use as components in life support devices or systems. Product qualification is performed according to internal EM quality standards for industrial products. For any special requirement (eg. automotive grade) please contact EM Microelectronic-Marin S.A. Copyright © 2006, EM Microelectronic-Marin SA 03/06 – rev.K 7 www.emmicroelectronic.com