B32227J6503M000

Film Capacitors Metallized Polyester Film Capacitors (MKT) Series/Type: Date: B32227 May 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Metallized polyester film capacitors (MKT) High voltage (wound) B32227 Typical applications Test and measurement equipment Laser, ultrasonic, X-ray, microwave Climatic Max. operating temperature: 85 °C Climatic category (IEC 60068-1): 40/085/21 Construction Dielectric: polyethylene terephthalate (polyester, PET) Flat winding Insulating sleeve Face ends sealed with epoxy resin Terminals Central axial wire leads, lead-free tinned Marking Manufacturer's logo, style (MKT), series number, rated capacitance, capacitance tolerance (code letter), rated DC voltage, date of manufacture (coded) Delivery mode Bulk (untaped) Dimensional drawing Dimensions in mm Width wmax Lead diameter d1 ≤6.0 0.6 8 ... 10 0.8 ≥10.5 1.0 When bending leads take care to leave a clearance of 1 mm to the capacitor body. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 18 B32227 High voltage (wound) Overview of available types Type Page VR (V DC) VRMS (V AC) CR (µF) 0.010 0.025 0.05 0.10 0.25 B32227 4 2500 220 4000 220 6300 220 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 18 B32227 High voltage (wound) Ordering codes and packing units VR VRMS CR f ≤60 Hz V DC V AC µF 2500 220 0.025 0.050 0.10 0.25 4000 220 0.010 0.025 0.050 0.10 6300 220 0.010 0.025 0.050 Max. dimensions w×h×l mm 8.5 × 18.0 × 33.0 12.5 × 25.5 × 33.0 10.5 × 26.5 × 45.0 15.5 × 40.5 × 45.0 9.5 × 22.0 × 33.0 10.0 × 22.5 × 45.0 12.5 × 31.0 × 45.0 16.5 × 42.0 × 45.0 9.0 × 21.5 × 45.0 13.5 × 32.5 × 45.0 17.0 × 42.0 × 45.0 Ordering code (composition see below) B32227J2253M000 B32227J2503M000 B32227J2104M000 B32227J2254M000 B32227J4103M000 B32227J4253M000 B32227J4503M000 B32227J4104M000 B32227J6103M000 B32227J6253M000 B32227J6503M000 Untaped pcs./MOQ 200 200 80 80 80 80 80 80 80 80 80 MOQ = Minimum Order Quantity, consisting of 4 packing units. Composition of ordering code Capacitance tolerance code: M = ±20% Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 18 B32227 High voltage (wound) Technical data Operating temperature range Max. operating temperature Top,max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR at 1 kHz: 8 at 10 kHz: 15 30 000 MΩ +85 °C +85 °C 40 °C +85 °C Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) Insulation resistance Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage Category voltage VC (continuous operation with VDC or VAC at f ≤ 60 Hz) Damp heat test Limit values after damp heat test 1.2 VR, 2 s TA (°C) DC voltage derating TA ≤ 70 VC = VR 70 0.1 µF) ≤ 5% (for CR ≤ 0.1 µF) ≤ 3 10-3 (at 1 kHz) ≤ 5 10-3 (at 10 kHz) ≥ 20% of minimum as-delivered values Reliability: Failure rate λ Service life tSL 10 fit (≤ 10 10-9 /h) at 0.5 VR, 40 °C 200 000 h at 1.0 VR, 40 °C For conversion to other operating conditions and temperatures, refer to chapter "Quality, 2 Reliability". Short circuit or open circuit Capacitance change ∆C/C Dissipation factor tan δ Insulation resistance Rins Failure criteria: Total failure Failure due to variation of parameters > 10% > 2 upper limit value < 150 MΩ Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 18 B32227 High voltage (wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt values Length of capacitor VR V DC 2500 4000 6300 k0 values Length of capacitor VR V DC 2500 4000 6300 VRMS V AC 220 220 220 k0 in V2/µs 125 000 320 000 62 500 160 000 500 000 33 mm 45 mm VRMS V AC 220 220 220 dV/dt in V/µs 25 40 12.5 20 40 33 mm 45 mm Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 18 B32227 High voltage (wound) Impedance Z versus frequency f (typical values) Permissible AC voltage VRMS versus frequency f Values can be obtained on request. In specific cases please provide a scaled voltage/ time graph and state operating conditions. Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 18 B32227 High voltage (wound) Mounting guidelines 1 1.1 Soldering Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature Soldering time Immersion depth Evaluation criteria: Visual inspection 1.2 235 ±5 °C 2.0 ±0.5 s 2.0 +0/ 0.5 mm from capacitor body or seating plane Wetting of wire surface by new solder ≥90%, free-flowing solder Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A. Conditions: Series Solder bath temperature Soldering time 10 ±1 s MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing > 10 mm) MFP MKP (lead spacing > 7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤ 7.5 mm) MKT uncoated (lead spacing ≤ 10 mm) insulated (B32559) 5 ±1 s