B32232A3684

Film Capacitors Metallized Polyester Film Capacitors (MKT) Series/Type: Date: B32232 May 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Metallized polyester film capacitors (MKT) General purpose (wound) B32232 Typical applications Smoothing Filtering Climatic Max. operating temperature: 100 °C Climatic category (IEC 60068-1): 40/100/21 Construction Dielectric: polyethylene terephthalate (polyester, PET) Cylindrical winding Insulating sleeve Face ends sealed with epoxy resin Terminals Central axial wire leads, lead-free tinned Marking Manufacturer, series number, rated capacitance (coded), capacitance tolerance (code letter), rated DC voltage. date of manufacture (coded) Dimensional drawing Dimensions in mm Diameter d ≤ 7.0 > 7.0 Lead diameter d1 0.6 0.8 When bending leads take care to leave a clearance of 1 mm to the capacitor body. Delivery mode Bulk (untaped) Taped (reel) For notes on taping, refer to chapter "Taping and packing“. Detail specification DIN 45910-112 Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 19 B32232 General purpose (wound) Overview of available types Type VR (V DC) VRMS (V AC) CR (µF) 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 B32232 100 63 250 160 400 200 630 200 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 19 B32232 General purpose (wound) Ordering codes and packing units VR VRMS CR f ≤60 Hz V DC V AC µF 100 63 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 250 160 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 400 200 0.10 0.15 0.22 0.33 0.47 0.68 1.0 Max. dimensions d×l mm 6.0 × 14.0 6.0 × 14.0 6.0 × 14.0 6.0 × 19.0 6.5 × 19.0 7.0 × 19.0 8.5 × 19.0 8.0 × 27.0 9.5 × 27.0 11.5 × 27.0 12.0 × 32.0 14.0 × 32.0 6.0 × 14.0 7.0 × 14.0 6.0 × 19.0 7.0 × 19.0 8.0 × 19.0 8.0 × 27.0 10.0 × 27.0 10.0 × 32.0 11.0 × 32.0 14.0 × 32.0 16.5 × 32.0 16.0 × 42.0 7.0 × 19.0 8.5 × 19.0 8.0 × 27.0 9.5 × 27.0 11.0 × 27.0 11.5 × 32.0 13.5 × 32.0 Ordering code (composition see below) B32232A1104+*** B32232A1154+*** B32232A1224+*** B32232A1334+*** B32232A1474+*** B32232A1684+*** B32232A1105+*** B32232A1155+*** B32232A1225+*** B32232A1335+*** B32232A1475+*** B32232A1685+*** B32232A3104+*** B32232A3154+*** B32232A3224+*** B32232A3334+*** B32232A3474+*** B32232A3684+*** B32232A3105+*** B32232A3155+*** B32232A3225+*** B32232A3335+*** B32232A3475+000 B32232A3685+000 B32232A6104+*** B32232A6154+*** B32232A6224+*** B32232A6334+*** B32232A6474+*** B32232A6684+*** B32232A6105+*** Reel pcs./MOQ 4000 4000 4000 4000 4000 4000 4000 4000 3600 2000 2000 2000 4000 4000 4000 4000 4000 4000 2000 2000 2000 2000 Untaped pcs./MOQ 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 1000 2000 2000 2000 2000 2000 2000 2000 2000 2000 1000 1000 800 2000 2000 2000 2000 2000 2000 2000 4000 4000 4000 3200 2000 2000 2000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% *** = Packaging code: 189 = Reel 000 = Untaped Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 19 B32232 General purpose (wound) Ordering codes and packing units VR VRMS CR f ≤60 Hz V DC V AC µF 630 200 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 Max. dimensions d×l mm 6.5 × 19.0 7.5 × 19.0 8.5 × 19.0 10.5 × 19.0 10.0 × 27.0 11.5 × 27.0 13.5 × 27.0 14.5 × 32.0 15.0 × 32.0 16.0 × 32.0 Ordering code (composition see below) B32232A8333+*** B32232A8473+*** B32232A8683+*** B32232A8104+*** B32232A8154+*** B32232A8224+*** B32232A8334+*** B32232A8474+000 B32232A8684+000 B32232A8105+000 Reel pcs./MOQ 4000 4000 4000 2000 2000 2000 2000 Untaped pcs./MOQ 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% *** = Packaging code: 189 = Reel 000 = Untaped Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 19 B32232 General purpose (wound) Technical data Operating temperature range Max. operating temperature Top,max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR CR ≤ 47 nF 1 kHz 10 10 10 kHz 20 25 VR CR ≤ 0.33 µF 100 V DC 3750 MΩ ≥ 250 V DC 7500 MΩ 1.4 VR, 2 s TA (°C) TA ≤ 85 85 1 µF 10 CR > 0.33 µF 1250 s 2500 s Dissipation factor tan δ (in 10-3) at at 20 °C (upper limit values) Insulation resistance Rins or time constant τ = CR Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage Category voltage VC (continuous operation with VDC or VAC at f ≤ 60 Hz) Operating voltage Vop for short operating periods (VDC or VAC at f ≤ 60 Hz) Damp heat test Limit values after damp heat test 47 nF < CR ≤ 1 µF DC voltage derating VC = VR VC = VR (165 TA)/80 DC voltage (max. hours) Vop = 1.25 VC (2000 h) AC voltage derating VC,RMS = VRMS VC,RMS=VRMS (165 TA)/80 AC voltage (max. hours) Vop = 1.0 VC,RMS (1000 h) 21 days/40 °C/93% relative humidity Capacitance change ∆C/C Dissipation factor change ∆ tan δ Insulation resistance Rins or time constant τ = CR Rins ≤ 5% ≤ 5 10-3 (at 1 kHz) ≤ 7 10-3 (at 10 kHz) ≥ 20% of minimum as-delivered values Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 19 B32232 General purpose (wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt values Length of capacitor VR VRMS V DC V AC 100 63 250 160 400 200 630 200 k0 values Length of capacitor VR VRMS V DC V AC 100 63 250 160 400 200 630 200 14 mm k0 in V2/µs 1 200 5 000 19 mm 27 mm 32 mm 42 mm 14 mm dV/dt in V/µs 6 10 19 mm 27 mm 32 mm 42 mm 3 5 7 10 2 3 4 7 1.5 2.5 3 5 2 600 2 500 5 600 12 500 400 1 500 3 200 8 800 300 1 250 2 400 6 300 1 000 Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 19 B32232 General purpose (wound) Impedance Z versus frequency f (typical values) Permissible AC voltage VRMS versus frequency f Values can be obtained on request. In specific cases please provide a scaled voltage/ time graph and state operating conditions. Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 19 B32232 General purpose (wound) Mounting guidelines 1 1.1 Soldering Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature Soldering time Immersion depth Evaluation criteria: Visual inspection 1.2 235 ±5 °C 2.0 ±0.5 s 2.0 +0/ 0.5 mm from capacitor body or seating plane Wetting of wire surface by new solder ≥90%, free-flowing solder Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A. Conditions: Series Solder bath temperature Soldering time 10 ±1 s MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing > 10 mm) MFP MKP (lead spacing > 7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤ 7.5 mm) MKT uncoated (lead spacing ≤ 10 mm) insulated (B32559) 5 ±1 s