B32237J2253M000

Film Capacitors Metallized Polyester Film Capacitors (MKT) Series/Type: Date: B32237 May 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Metallized polyester film capacitors (MKT) High voltage (wound) B32237 Typical applications Test and measurement equipment Laser, ultrasonic, X-ray, microwave Climatic Max. operating temperature: 85 °C Climatic category (IEC 60068-1): 40/085/21 Construction Dielectric: polyethylene terephthalate (polyester, PET) Cylindrical winding In tubular plastic case Face ends sealed with epoxy resin Terminals Central axial wire leads, lead-free tinned Marking Manufacturer's logo, style (MKT), series number, rated capacitance (coded), capacitance tolerance (code letter), rated DC voltage, date of manufacture (coded) Delivery mode Bulk (untaped) Dimensional drawing Dimensions in mm When bending leads take care to leave a clearance of 1 mm to the capacitor body. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 17 B32237 High voltage (wound) Overview of available types Type VR (V DC) VRMS (V AC) CR (nF) 0.68 1.0 2.5 5.0 10 25 B32237 2500 200 4000 450 6300 450 8000 450 10000 450 12500 450 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 17 B32237 High voltage (wound) Ordering codes and packing units VR V DC 2500 VRMS CR f ≤60 Hz V AC nF 200 2.5 5.0 10 25 450 1.0 2.5 5.0 10 450 1.0 2.5 5.0 10 450 1.0 2.5 5.0 10 450 1.0 2.5 5.0 450 0.68 1.0 2.5 Max. dimensions d×l mm 8.5 × 33.0 9.5 × 33.0 10.5 × 33.0 16.5 × 33.0 7.5 × 33.0 8.5 × 33.0 10.5 × 33.0 12.5 × 33.0 8.5 × 33.0 10.5 × 33.0 10.5 × 45.0 13.5 × 45.0 8.5 × 45.0 10.5 × 45.0 12.5 × 45.0 16.5 × 45.0 8.5 × 56.0 11.5 × 56.0 13.5 × 56.0 9.5 × 56.0 9.5 × 56.0 12.5 × 56.0 Ordering code (composition see below) B32237J2252M000 B32237J2502M000 B32237B2103M000 B32237J2253M000 B32237A4102M000 B32237J4252M000 B32237J4502M000 B32237B4103M000 B32237B6102M000 B32237B6252M000 B32237B6502M000 B32237B6103M000 B32237A8102M000 B32237B8252M000 B32237A8502M000 B32237J8103M000 B32237A9102M000 B32237A9252M000 B32237A9502M000 B32237A3681M000 B32237A3102M000 B32237A3252M000 Untaped pcs./MOQ 400 400 400 200 400 400 400 200 400 400 400 200 400 400 200 200 400 200 200 400 400 200 4000 6300 8000 10000 12500 MOQ = Minimum Order Quantity, consisting of 4 packing units. Composition of ordering code Capacitance tolerance code: M = ±20% Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 17 B32237 High voltage (wound) Technical data Operating temperature range Max. operating temperature Top,max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR at 1 kHz: 8 10-3 at 10 kHz: 15 10-3 30 000 MΩ +85 °C +85 °C 40 °C +85 °C Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) Insulation resistance Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage Category voltage VC (continuous operation with VDC or VAC at f ≤ 60 Hz) Damp heat test Limit values after damp heat test 1.2 VR, 2 s TA (°C) DC voltage derating TA ≤ 70 VC = VR 70 10% > 2 upper limit value < 150 MΩ Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 17 B32237 High voltage (wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt and k0 values VR (V DC) 2 500 4 000 6 300 8 000 10 000 12 500 VRMS (V AC) 200 450 450 450 450 450 dV/dt in V/µs 25 40 50 50 370 1000 k0 in V2/µs 125 000 320 000 630 000 800 000 7 500 000 25 000 000 Impedance Z versus frequency f (typical values) Permissible AC voltage VRMS versus frequency f Values can be obtained on request. In specific cases please provide a scaled voltage/ time graph and state operating conditions. Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 17 B32237 High voltage (wound) Mounting guidelines 1 1.1 Soldering Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature Soldering time Immersion depth Evaluation criteria: Visual inspection 1.2 235 ±5 °C 2.0 ±0.5 s 2.0 +0/ 0.5 mm from capacitor body or seating plane Wetting of wire surface by new solder ≥90%, free-flowing solder Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A. Conditions: Series Solder bath temperature Soldering time 10 ±1 s MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing > 10 mm) MFP MKP (lead spacing > 7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤ 7.5 mm) MKT uncoated (lead spacing ≤ 10 mm) insulated (B32559) 5 ±1 s