B32325-A1355

AC Film Capacitors Lighting B 32 325 Construction Dielectric: polypropylene film Plastic case Polyurethane resin Internal discharge resistor Features Self-healing properties Low dissipation factor High insulation resistance Typical applications For general sine wave applications, mainly as series and parallel connection lighting capacitor Terminals Push-in terminals Mounting parts Metal stud (max. torque = 5 Nm) Plastic stud (max. torque = 3 Nm) Technical data and specifications Standard Rated capacitance CN Tolerance Rated voltage UN Rated frequency fN Life expectancy Maximum ratings Maximum permissible voltage Umax Maximum permissible current Imax 1,1 x UN (UN: rated voltage) 1,3 x IN (IN : rated current) IEC / EN 61048 / 61049 (except destruction test) 2 .. 25 µF ± 5% , ±10% 250 Vac 50.. 60 Hz 10 years Issue No. 2 07/01 Page 1 of 4 AC Film Capacitors Lighting B 32 325 Technical data (cont`d) Test data AC test voltage terminal to terminal UTT Insulation voltage terminals to case Insulation resistance Ris or time τ constant at 20 °C Rel. Humidity ≤ 65 °C (minimum value) Dissipation factor tanδ at 20 °C Maximum rate of voltage rise du/dtmax Climatic data Climatic category Lower category Tmin Upper category Tmax Damp heat test ttest Permitted capacitance ∆C/C 25/085/21 in accordance with IEC 60068-1 -25 °C +85 °C 21 days ≤3% 3000 s ≤ 1,0 x 10 10 V/µs -3 2.0 x UN , 60s 2000 Vac (120 Hz) Note : 1) It should be noted that presence of harmonics produces over voltage & over current on capacitors. Resonance may cause serious damage to installation if a siginificant level of total harmonic distortion level exists for voltage or current. In such cases, series reactors must be considered. 2) Operating temperature class: In accordance with the reference standards, these temperatures are those measured on the surface on the capacitor Issue No. 2 07/01 Page 2 of 4 AC Film Capacitors Lighting B 32 325 Dimensional drawings Issue No. 2 07/01 Page 3 of 4 AC Film Capacitors Lighting B 32 325 Ordering codes and packing units UN Vac 250 CN µF 2 3 3.25 3.5 4 5 6 7 8 9 10 12 15 20 22 25 Max. dimensions d x l (mm) 25 x 58 25 x 58 25 x 58 25 x 58 25 x 58 25 x 58 30 x 60 30 x 60 30 x 60 30 x 60 35 x 60 35 x 60 35 x 70 35 x 70 40 x 70 40 x 70 B32325-A1205-+0$0 112 B32325-A1305-+0$0 112 B32325-A1325-+5$0 112 B32325-A1355-+0$0 112 B32325-A1405-+0$0 112 B32325-A1505-+0$0 112 B32325-A1605-+0$0 112 B32325-A1705-+0$0 112 B32325-A1805-+0$0 112 B32325-A1905-+0$0 112 B32325-A1106-+0$0 84 B32325-A1126-+0$0 84 B32325-A1156-+0$0 84 B32325-A1206-+0$0 84 B32325-A1226-+0$0 45 B32325-A1256-+0$0 45 Ordering code Packing unit (pcs.) Notes for ordering code: + Replace for capacitance tolerance J - ± 5% K- ± 10% $ Replace for construction 1 - Plastic case FR (UL94 V-1) 3 - Plastic case FR (UL94 V-1) and M8 bolt  EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. Issue No. 2 07/01 Page 4 of 4