B32671L0822

Film Capacitors Metallized Polypropylene Film Capacitors (MKP) Series/Type: Date: B32671L ... B32672L October 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Metallized polypropylene film capacitors (MKP) High V AC, high temperature (wound) B32671L ... B32672L Typical applications Electronic ballasts (resonant circuits) SMPS High-frequency AC loads Pulse circuits Climatic Max. operating temperature: 125 °C Climatic category (IEC 60068-1): 55/110/56 Construction Dielectric: metallized polypropylene (PP) Wound capacitor technology Plastic case (UL 94 V-0) Epoxy resin sealing Features Very high AC voltages for all frequency ranges Very small dimensions High peak voltage for short time periods High peak current High pulse withstand capability Terminals Parallel wire leads, lead-free tinned Special lead lengths available on request Marking Manufacturer's logo, lot number, type number, rated capacitance (coded), capacitance tolerance (code letter), rated AC voltage, date of manufacture (coded) Dimensional drawing Dimensions in mm Lead spacing ±0.4 10 15 Lead diameter Type d1 0.6 B32671L 0.8 B32672L Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For notes on taping, refer to chapter "Taping and packing“. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 31 B32671L ... B32672L High V AC, high temperature (wound) Overview of available types Lead spacing 10 mm Type Page VRMS (V AC) VR (V DC) CR (nF) 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.10 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 47 56 68 100 150 220 330 470 680 1000 B32671L 4 200 400 250 630 250 500 600 15 mm B32672L 6 160 200 420 250 630 250 500 600 700 1000 1000 1600 250 1000 1300 1600 2000 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 31 B32671L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 10 mm) VRMS VR CR f ≤1 kHz V AC V DC nF 200 400 22 33 47 68 100 250 630 15 22 33 47 56 250 1000 4.7 6.8 10 15 22 500 1000 3.3 3.9 4.1 4.7 5.6 6.2 6.8 8.2 10 12 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 Ordering code (composition see below) B32671L4223+*** B32671L4333+*** B32671L4473+*** B32671L4683+*** B32671L4104+*** B32671L6153+*** B32671L6223+*** B32671L6333+*** B32671L6473+*** B32671L6563+*** B32671L9472+*** B32671L9682+*** B32671L9103+*** B32671L9153+*** B32671L9223+*** B32671L0332+*** B32671L0392+*** B32671L0412+*** B32671L0472+*** B32671L0562+*** B32671L0622+*** B32671L0682+*** B32671L0822+*** B32671L0103+*** B32671L0123+*** Ammo pack pcs./MOQ 4000 4000 3320 3320 2720 4000 3320 3320 2720 2720 4000 4000 3320 3320 2720 4000 4000 4000 4000 3320 3320 3320 3320 2720 2720 Reel pcs./ MOQ 6800 6800 5200 5200 4400 6800 5200 5200 4400 4400 6800 6800 5200 5200 4400 6800 6800 6800 6800 5200 5200 5200 5200 4400 4400 Untaped pcs./ MOQ 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 31 B32671L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 10 mm) VRMS VR CR f ≤1 kHz V AC V DC nF 600 1600 1.2 1.5 2.2 2.7 3.3 3.9 4.1 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 Ordering code (composition see below) B32671L1122+*** B32671L1152+*** B32671L1222+*** B32671L1272+*** B32671L1332+*** B32671L1392+*** B32671L1412+*** Ammo pack pcs./MOQ 4000 3320 3320 3320 2720 2720 2720 Reel pcs./ MOQ 6800 5200 5200 5200 4400 4400 4400 Untaped pcs./ MOQ 4000 4000 4000 4000 4000 4000 4000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 31 B32672L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 15 mm) VRMS f ≤1 kHz V AC 160 VR CR Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.0 × 14.0 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 Ordering code (composition see below) B32672L2154+*** B32672L2224+*** B32672L2334+*** B32672L2474+*** B32672L2684+*** B32672L2105+*** B32672L4683+*** B32672L4104+*** B32672L4154+*** B32672L4224+*** B32672L4334+*** B32672L4474+*** B32672L4684+*** B32672L6333+*** B32672L6473+*** B32672L6683+*** B32672L6104+*** B32672L6154+*** B32672L6224+*** B32672L0103+*** B32672L0153+*** B32672L0223+*** B32672L0333+*** B32672L0473+*** B32672L0683+*** B32672L0104+*** Ammo pack pcs./MOQ 4680 3840 3320 2720 2560 4680 4680 3840 3320 2920 2560 4680 4680 3840 3320 2720 2560 4680 4680 4680 3840 3320 2720 2560 Reel pcs./ MOQ 5200 4400 3600 2800 2800 2200 5200 5200 4400 3600 3000 2800 2200 5200 5200 4400 3600 2800 2800 5200 5200 5200 4400 3600 2800 2800 Untaped pcs./ MOQ 4000 4000 4000 2000 2000 1000 4000 4000 4000 4000 2000 2000 1000 4000 4000 4000 4000 2000 2000 4000 4000 4000 4000 4000 2000 2000 200 250 250 V DC nF 250 150 220 330 470 680 1000 420 68 100 150 220 330 470 680 630 33 47 68 100 150 220 1000 10 15 22 33 47 68 100 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 31 B32672L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 15 mm) VRMS f ≤1 kHz V AC 500 VR CR Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 6.0 × 11.0 × 18.0 6.0 × 12.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 6.0 × 11.0 × 18.0 6.0 × 11.0 × 18.0 6.0 × 12.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 Ordering code (composition see below) B32672L7682+*** B32672L7103+*** B32672L7223+*** B32672L7333+*** B32672L7473+*** B32672L1622+*** B32672L1682+*** B32672L1822+*** B32672L1103+*** B32672L1123+*** B32672L1153+*** B32672L1223+*** B32672L1333+*** B32672L8102+*** B32672L8122+*** B32672L8152+*** B32672L8222+*** B32672L8272+*** B32672L8332+*** B32672L8392+*** B32672L8412+*** B32672L8472+*** B32672L8562+*** B32672L8622+*** B32672L8682+*** B32672L8822+*** B32672L8103+*** B32672L8123+*** B32672L8153+*** B32672L8223+*** Ammo pack pcs./MOQ 4680 4680 3320 2720 2560 4680 4680 3840 3840 3840 3320 2720 2560 4680 4680 4680 4680 4680 4680 4680 4680 4680 3840 3840 3840 3840 3320 2720 2720 2560 Reel pcs./ MOQ 5200 5200 3600 2800 2800 5200 5200 4400 4400 4400 3600 2800 2800 5200 5200 5200 5200 5200 5200 5200 5200 5200 4400 4400 4400 4400 3600 2800 2800 2800 Untaped pcs./ MOQ 4000 4000 4000 2000 2000 4000 4000 4000 4000 4000 4000 2000 2000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 2000 2000 2000 600 700 V DC nF 1300 6.8 10 22 33 47 1600 6.2 6.8 8.2 10 12 15 22 33 2000 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.1 4.7 5.6 6.2 6.8 8.2 10 12 15 22 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 31 B32671L ... B32672L High V AC, high temperature (wound) Technical data Operating temperature range Max. operating temperature Top,max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR 0.8 1 kHz 0.8 10 kHz 1.0 1.0 100 kHz 2.0 3.0 > 100 GΩ (CR ≤ 0.33 µF) > 30 000 s (CR > 0.33 µF) +125 °C +110 °C 55 °C +85 °C 0.8 1.0 0.8 Dissipation factor tan δ (in 10-3) at at 20 °C (upper limit values) ≤27 nF 27 nF< CR ≤0.1 µF 0.1 µF < CR ≤1 µF >1 µF Insulation resistance Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage 1.6 VR, 2 s TA (°C) DC voltage derating AC voltage derating Category voltage VC (continuous operation with VDC TA ≤ 85 VC = VR VC,RMS = VRMS or VAC at f ≤ 1 kHz) 85 4 upper limit values Insulation resistance Rins < 1500 MΩ Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 31 B32671L ... B32672L High V AC, high temperature (wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt values Lead spacing Type VRMS (V AC) VR (V DC) CR (nF) 1.2 1.5 2.2 2.7 3.3 3.9 4.1 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 47 56 68 100 10 mm B32671L 200 400 dV/dt in V/µs 250 630 1000 500 1000 600 1600 6 000 5 600 5 200 5 000 4 700 4 500 4 400 810 810 810 540 540 540 540 540 810 810 4 700 4 300 4 100 3 800 3 400 3 200 3 100 2 700 2 500 2 300 400 400 400 400 400 Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 31 B32671L ... B32672L High V AC, high temperature (wound) dV/dt values Lead spacing Type VRMS (V AC) VR (V DC) CR (nF) 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.1 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 47 56 68 100 150 220 330 470 680 1000 15 mm B32672L 160 200 250 420 dV/dt in V/µs 250 630 1000 500 1000 600 1600 700 2000 10 000 9 400 9 000 7 500 7 100 6 800 6 000 5 700 5 500 5 000 4 700 4 500 4 200 3 900 3 600 3 300 2 900 1 000 445 445 445 445 445 445 445 1 000 300 300 200 200 200 200 200 200 200 300 300 300 300 1 000 1 000 1 000 3 600 3 500 3 100 2 800 2 600 2 300 2 000 1 700 170 170 170 170 170 170 Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 31 B32671L ... B32672L High V AC, high temperature (wound) k0 values Lead spacing Type VRMS (V AC) VR (V DC) CR (nF) 1.2 1.5 2.2 2.7 3.3 3.9 4.1 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 47 56 68 100 10 mm B32671L 200 400 k0 in V2/µs 250 630 1000 500 1000 600 1600 14 400 000 14 000 000 13 800 000 13 600 000 13 300 000 13 100 000 13 000 000 400 000 400 000 400 000 200 000 200 000 200 000 200 000 200 000 400 000 400 000 16 000 000 13 600 000 12 300 000 9 900 000 8 400 000 7 700 000 7 400 000 7 200 000 7 000 000 6 400 000 150 000 150 000 150 000 150 000 150 000 Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 31 B32671L ... B32672L High V AC, high temperature (wound) k0 values Lead spacing Type VRMS (V AC) VR (V DC) CR (nF) 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.1 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 47 56 68 100 150 220 330 470 680 1000 15 mm B32672L 160 200 250 420 k0 in V2/µs 250 630 1000 500 1000 600 1600 700 2000 20 300 000 19 600 000 19 200 000 18 600 000 18 200 000 18 000 000 16 800 000 16 200 000 15 800 000 13 100 000 12 700 000 12 300 000 11 800 000 11 100 000 10 600 000 10 400 000 9 300 000 1 000 000 1 000 000 1 000 000 1 000 000 1 000 000 1 000 000 1 000 000 500 000 500 000 120 000 120 000 120 000 120 000 120 000 120 000 500 000 500 000 500 000 500 000 18 600 000 3 000 000 17 400 000 15 400 000 3 000 000 13 800 000 12 600 000 12 300 000 3 000 000 11 800 000 3 000 000 11 000 000 3 000 000 100 000 100 000 100 000 100 000 100 000 100 000 Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 31 B32671L ... B32672L High V AC, high temperature (wound) Impedance Z versus frequency f (typical values) Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 31 B32671L High V AC, high temperature (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C) For TA >100 °C, please refer to "General technical information", section 3.2.3. Lead spacing 10 mm 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC 1000 V DC/500 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 31 B32671L High V AC, high temperature (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C) For TA >100 °C, please refer to "General technical information", section 3.2.3. Lead spacing 10 mm 1600 V DC/600 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 31 B32672L High V AC, high temperature (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please refer to "General technical information", section 3.2.3. Lead spacing 15 mm 250 V DC/160 V AC 420 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 31 B32672L High V AC, high temperature (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please refer to "General technical information", section 3.2.3. Lead spacing 15 mm 1300 V DC/500 V AC 1600 V DC/600 V AC 2000 V DC/700 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 31 B32671L ... B32672L High V AC, high temperature (wound) Operation at overvoltages during heating and ignition of lamps (TA ≤40 °C) In lighting applications, the capacitors can be subjected to overvoltages during the heating and ignition periods. An overvoltage occurs when the operation voltage exceeds the permissible AC voltage at the resonant frequency fr. For a repetitive application of on/off switching pulses (as for example in the life tests applied by electronic ballast manufacturers), limits have to be imposed on the time periods under overvoltage and on the duty cycle, in order to keep the capacitance value within the required margins: The overvoltage time tOV should be less than 1 sec. The maximum duty cycle of the overvoltage is given by where VRMS,ov is the RMS voltage during period tOV and VRMS is the permissible AC voltage for continuous operation at the resonant frequency fr (given by the “permissible AC voltage versus frequency f” graphics in theprevious pages). The drift of capacitance depends on the Vpp attained, and the total time under overvoltage, which is calculated in hours as follows: (Ni tOV) / 3600 where Ni is the number of overvoltage impulses and tOV is expressed in seconds. The maximum drift of capacitance as a function of both parameters is provided graphically in the following pages. Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 31 B32671L High V AC, high temperature (wound) Estimation of the maximum drift of capacitance value in function of the number of total hours overvoltage Lead spacing 10 mm 500 V AC/1000 V DC 600 V AC/1600 V DC Please read Cautions and warnings and Important notes at the end of this document. Page 19 of 31 B32672L High V AC, high temperature (wound) Estimation of the maximum drift of capacitance value in function of the number of total hours overvoltage Lead spacing 15 mm 600 V AC/1600 V DC 700 V AC/2000 V DC Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 31 B32671L ... B32672L High V AC, high temperature (wound) Mounting guidelines 1 1.1 Soldering Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature Soldering time Immersion depth Evaluation criteria: Visual inspection 1.2 235 ±5 °C 2.0 ±0.5 s 2.0 +0/ 0.5 mm from capacitor body or seating plane Wetting of wire surface by new solder ≥90%, free-flowing solder Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A. Conditions: Series Solder bath temperature Soldering time 10 ±1 s MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing > 10 mm) MFP MKP (lead spacing > 7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤ 7.5 mm) MKT uncoated (lead spacing ≤ 10 mm) insulated (B32559) 5 ±1 s