B3291

EMI Suppression Capacitors (MKP) B3291* Series Series/Type: B32911 … B32916 Ordering code: Date: Version: May 2007 1 Content of inside pages of data sheet. Data will be automatically entered into frontpage headlines, headers and footers. Please fill in the table and then change the colour to “White”. This ensures that the table disappears for the customer pdf. Identification/Classification 1: (header 1) Identification/Classification 2: (header 2) Ordering code: Series/Type: Preliminary data (optional): (if necessary) Department: Date: B32911 … B32916 Preliminary data FK DC PM May 2007 EMI Suppression Capacitors (MKP) B3291* Series © EPCOS AG 2007. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EMI Suppression Capacitors (MKP) Preliminary data Recommended applications X1 class for interference suppression “Across the line” applications. For apparatus permanently connected to mains and isolated from direct contact with humidity Climatic Maximum operating temperature 110 ºC Climatic category (IEC 60068-1): 40/110/56 Construction Dielectric: Polypropylene (MKP) Plastic case (UL 94 V-0) Epoxy resin sealing (UL 94 V-0) Features Very small dimensions Good self-healing properties High voltage capability Terminals Parallel wire leads, lead-free tinned Standard lead lengths: 6 –1 mm Special lead lengths are available on request Marking Manufacturer’s logo and lot number, date code, rated capacitance (coded), capacitance tolerance (code letter) and rated ac voltage (IEC) Series number, sub-class (X1), dielectric code (MKP), climatic category, passive flammability category, approvals. Delivery mode Bulk (untaped) Taped (Ammo pack or Reel) Technical data Rated AC voltage (IEC 60384-14) Maximum continuous DC voltage (V DC) Maximum operating temperature Top,max DC test voltage Dissipation factor tan δ (in 10 ) at 20 °C, (upper limit values) Insulation resistance Rins or time constant τ = CR ·⋅ Rins at 100 V DC, 20 °C, rel. humidity ≤ 65% and for 60 s (minimum “as delivered” values) Passive flammability category to IEC 40 (CO) 752 Capacitance tolerances (measured at 1 kHz) –3 B3291* Series X1 / 330 V AC Dimensional drawing Dimensions in mm Lead spacing ±0.4 (mm) 10 15 ... 27.5 37.5 Lead diameter d1 (mm) 0.6 0.8 1.0 Type B32911 B32912 ... 14 B32916 Marking examples: = 10mm 15 ≤ ≤ 27.5 mm (CR ≤ 1 µF) 22.5 ≤ ≤ 37.5 mm (CR > 1 µF) 330 V (50/60 Hz) 760 V +110 ºC 2500 V, 2 s at 1 kHz CR ≤ 0.33 µF 100,000 MΩ B ±10% (K), ±20% (M) C ≤ 2.2 µF 1 CR > 0.33 µF 30,000 s C > 2.2 µF 2 FK DC PM Page 2 of 4 May 2007 EMI Suppression Capacitors (MKP) Preliminary data Ordering codes and packing units ±0.4 (mm) B3291* Series X1 / 330 V AC CR mm 10 10 22 33 22 33 47 68 0 .1 0 .15 0 .15 0 .22 0 .22 0 .33 0 .15 0 .22 0 .33 0 .47 0 .47 0 .68 1 .0 1 .5 2 .2 3 .3 4 .7 6 .8 nF nF nF nF nF nF nF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF µF 15 22.5 27.5 37.5 Max dimensions w×h×l mm 4.0 × 9.0 5.0 × 11.0 6.0 × 12.0 5.0 × 10.5 5.0 × 10.5 5.0 × 10.5 6.0 × 11.0 7.0 × 12.5 7.0 × 12.5 8.5 × 14.5 8.5 × 14.5 9.0 × 17.5 9.0 × 17.5 6.0 × 15.0 7.0 × 16.0 8.5 × 16.5 10.5 × 18.5 11.0 × 21.0 11.0 × 21.0 13.5 × 23.0 18.0 × 27.5 19.0 × 30.0 18.0 × 32.5 20.0 × 39.5 28.0 × 42.5 Ordering code Ammo pack pcs/unit 1000 830 680 1170 1170 1170 960 830 830 680 680 640 640 680 580 480 390 - Reel pcs/unit 1700 1300 1100 1300 1300 1300 1100 900 900 700 700 700 700 700 600 500 400 350 350 250 - Untaped pcs/unit 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 500 500 500 720 630 510 540 320 320 260 200 180 90 75 55 × × × × × × × × × × × × × × × × × × × × × × × × × 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 31.5 31.5 31.5 31.5 31.5 41.5 41.5 41.5 B32911A3103+*** B32911B3223+*** B32911A3333M*** B32912A3223+*** B32912A3333+*** B32912A3473+*** B32912A3683+*** B32912A3104+*** B32912B3154M*** B32912A3154+*** B32912B3224M*** B32912A3224+*** B32912B3334M*** B32913A3154+*** B32913A3224+*** B32913A3334M*** B32913A3474M*** B32914A3474+*** B32914B3684+*** B32914A3105+*** B32914A3155+*** B32914A3225M*** B32916A3335+*** B32916A3475M*** B32916A3685M*** Further E series and intermediate capacitance values are available on request. Composition of ordering code + = Capacitance tolerance code M = ±20% K = ±10% *** = Packing code 289 = ammo pack 189 = reel pack 000 = untaped (lead length 6 –1 mm) Approvals Standards EN 132400 / IEC 60384-14 (330 V AC) UL1414 (250 V AC) UL1283 (330 V AC) CSA C22.2 No.1 (250 V AC) CSA C22.2 No.8 (330 V AC) Certificate 40018909 & 40010694 E97863 E157153 E97863 E157153 () () Marks of Conformity ¹ ¹ approved by UL dV/dt and K0 values ±0.4 (mm) dV/dt (V/µs) K0 (V /µs) 2 10 550 473,000 15 400 344,000 22.5 200 172,000 27.5 150 129,000 37.5 100 86,000 Note: The maximum values of dV/dt and K0 must not be exceeded in order to avoid overheating of the capacitor. FK DC PM Page 3 of 4 May 2007 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. FK DC PM Page 4 of 4 May 2007