B32914A3155M

Film Capacitors EMI Suppression Capacitors (MKP) Series/Type: B32911*3 ... B32916*3 Date: June 2020 © TDK Electronics AG 2020. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics' prior express consent is prohibited. EMI suppression capacitors (MKP) B32911*3 ... B32916*3 X1 / 330 V AC Typical applications X1 class for interference suppression "Across the line" applications Dimensional drawing Climatic Max. operating temperature: 110 °C Climatic category (IEC 60068-1:2013): 40/110/56 Construction Dielectric: polypropylene (MKP) Plastic case (UL 94 V-0) Epoxy resin sealing (UL 94 V-0) Features Very small dimensions Good self-healing properties High voltage capability RoHS-compatible Halogen-free capacitors available on request Terminals Parallel wire leads, lead-free tinned Special lead lengths available on request Dimensions in mm Lead spacing ±0.4 Lead diameter d1 ±0.05 Type 10 0.6 B32911*3 15 ... 27.5 0.8 B32912*3 ... B32914*3 37.5 1.0 B32916*3 Marking Manufacturer's logo, lot number, date code, rated capacitance (coded), capacitance tolerance (code letter), rated AC voltage (IEC), series number, sub-class (X1), dielectric code (MKP), climatic category, passive flammability category, approvals. Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For taping details, refer to chapter "Taping and packing". Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 21 B32911*3 ... B32916*3 X1 / 330 V AC Marking example (position of marks may vary): Approvals Approval marks Notes: Standards EN 60384-14:2014/A1:2016 IEC 60384-14:2013/AMD1:2016 UL 1414:2000 UL 1283:2005 CSA C22.2 No.1:2004 CSA C22.2 No.8:2013 UL 60384-14:2014 CSA E60384-14:2013 Certificate 40032766 (approved by VDE) (C ≤ 10 μF) E97863 / E157153 E97863 / E157153 (approved by UL) E97863 (approved by UL) Effective January 2014, only for EMI supression capacitors:  UL 60384-14:2014 certification replaces both UL 1414:2000 and UL 1283:2005 standards.  CSA C22.2 No.1.2004 and CSA C22.2 No.8:2013 are replaced by CSA E60384-14:2013.  References like 1414, 1283 are removed from the capacitor marking. Capacitors under UL 1414:2000, UL 1283:2005 produced during or before 2013, are accepted under UL scope. Capacitors under CSA C22.2 No.1:2004 / CSA C22.2 No.8:2013 produced during or before 2013, are accepted under cUL scope. Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 21 B32911*3 ... B32916*3 X1 / 330 V AC Overview of available types Lead spacing 10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm Type B32912*3 B32913*3 B32914*3 B32916*3 B32911*3 CR (μF) 0.010 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 21 B32911*3 ... B32916*3 X1 / 330 V AC Ordering codes and packing units Lead spacing CR mm 10 15 22.5 μF 0.010 0.022 0.033 0.022 0.033 0.047 0.068 0.10 0.15 0.15 0.22 0.22 0.33 0.15 0.22 0.33 0.47 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 9.0 × 17.5 × 18.0 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 18.5 × 26.5 Ordering code (composition see below) B32911A3103+*** B32911B3223+*** B32911A3333M*** B32912A3223+*** B32912A3333+*** B32912A3473+*** B32912A3683+*** B32912A3104+*** B32912B3154M*** B32912A3154+*** B32912B3224M*** B32912A3224+*** B32912B3334M*** B32913A3154+*** B32913A3224+*** B32913A3334M*** B32913A3474M*** Ammo pack pcs./MOQ 4000 3320 2720 4680 4680 4680 3840 3320 3320 2720 2720 2560 2560 2720 2320 1920 1560 Reel Untaped pcs./MOQ 6800 5200 4400 5200 5200 5200 4400 3600 3600 2800 2800 2800 2800 2800 2400 2000 1600 pcs./MOQ 4000 4000 4000 4000 4000 4000 4000 4000 4000 2000 2000 2000 2000 2880 2520 2040 2160 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: M = ±20% K = ±10% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Straight terminals, untaped (lead length 3.2 ±0.3 mm) 000 = Straight terminals, untaped (lead length 6 1 mm) Page 5 of 21 B32911*3 ... B32916*3 X1 / 330 V AC Ordering codes and packing units Lead spacing CR mm 27.5 37.5 μF 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 Max. dimensions w×h×l mm 11.0 × 21.0 × 31.5 11.0 × 21.0 × 31.5 13.5 × 23.0 × 31.5 18.0 × 27.5 × 31.5 19.0 × 30.0 × 31.5 18.0 × 32.5 × 41.5 20.0 × 39.5 × 42.0 28.0 × 42.5 × 42.0 Ordering code (composition see below) B32914A3474+*** B32914B3684+*** B32914A3105+*** B32914A3155+*** B32914A3225M*** B32916A3335M*** B32916A3475M*** B32916A3685M*** Ammo pack pcs./MOQ         Reel Untaped pcs./MOQ 1400 1400 1000      pcs./MOQ 1280 1280 1040 800 720 720 640 440 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: M = ±20% K = ±10% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Straight terminals, untaped (lead length 3.2 ±0.3 mm) 000 = Straight terminals, untaped (lead length 6 1 mm) Page 6 of 21 B32911*3 ... B32916*3 X1 / 330 V AC Technical data Reference standard: IEC 60384-14:2013/AMD1:2016 / UL 60384-14:2014/A1:2016. All data given at T = 20 °C, unless otherwise specified. Rated AC voltage (IEC 60384-14:2013) 330 V (50/60 Hz) Maximum continuous DC voltage VDC 760 V at Top ≤ 85 °C 1.5% / °C derating when 85 °C < Top ≤ 110 °C Max. operating temperature Top,max +110 °C DC test voltage 2500 V, 2 s The repetition of this DC voltage test may damage the capacitor. Special care must be taken in case of use several capacitors in a parallel configuration. Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) at CR ≤ 2.2 μF CR > 2.2 μF Insulation resistance Rins or time constant τ = CR  Rins at 100 V DC, 20 °C, rel. humidity ≤ 65% and for 60 s (minimum as-delivered values) CR ≤ 0.33 μF CR > 0.33 μF 100 000 MΩ 30 000 s Passive flammability category B 1 kHz 1 2 Capacitance tolerances (measured at 1 kHz) ±10% (K), ±20% (M) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/μs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/μs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt and k0 values Lead spacing dV/dt in V/μs k0 in V2/μs 10 mm 550 473 000 Please read Cautions and warnings and Important notes at the end of this document. 15 mm 400 344 000 22.5 mm 200 172 000 Page 7 of 21 27.5 mm 150 129 000 37.5 mm 100 86 000 B32911*3 ... B32916*3 X1 / 330 V AC Testing and Standards Test Reference Conditions of test Electrical IEC parameters 60384-14:2013/ AMD1:2016 Voltage Proof: Between terminals, 4.3 VR, 1 min. Terminals and enclosure: 2 VR + 1500 V AC Insulation resistance, Rins Capacitance, C Dissipation factor, tan δ Robustness IEC Tensile strength (test Ua1) of termina- 60068-2-21:2006 Wire diameter Tensile tions force 0.5 < d1 ≤ 0.8 mm 10 N 0.8 < d1 ≤ 1.25 mm 20 N Solder bath temperature at Resistance IEC to soldering 60068-2-20:2008, 260 ±5 °C, immersion for test Tb, 10 seconds heat method 1A Performance requirements Within specified limits Capacitance and tan δ within specified limits ΔC/C0 ≤ 5% tan δ within specified limits Rapid IEC change of 60384-14:2013/ temperature AMD1:2016 TA = lower category temperature No visible damage TB = upper category temperature ΔC/C0 ≤ 5% Five cycles, duration t = 30 min. tan δ within specified limits Vibration IEC 60384-14:2013/ AMD1:2016 Bump IEC 60384-14:2013/ AMD1:2016 Climatic sequence IEC 60384-14:2013/ AMD1:2016 Test FC: vibration sinusoidal No visible damage Displacement: 0.75 mm Accleration: 98 m/s2 Frequency: 10 Hz ... 500 Hz Test duration: 3 orthogonal axes, 2 hours each axe Test Eb: Total 4000 bumps with No visible damage ΔC/C0 ≤ 5% 400 m/s2 mounted on PCB tan δ within specified limits 6 ms duration No visible damage Dry heat Tb / 16 h ΔC/C0 ≤ 5% Damp heat cyclic, 1st cycle +55 °C / 24 h / 95% ... 100% RH Δ tan δ ≤ 0.008 for C ≤ 1 μF Δ tan δ ≤ 0.005 for C > 1 μF Cold Ta / 2 h Voltage proof Damp heat cyclic, 5 cycles +55 °C / 24 h / 95% ... 100% RH Rins ≥ 50% of initial limit Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 21 B32911*3 ... B32916*3 X1 / 330 V AC Test Reference Damp heat, IEC steady 60384-14:2013/ state AMD1:2016 Impulse test Endurance IEC 60384-14:2013/ AMD1:2016 Conditions of test Test Ca 40 °C / 93% RH / 56 days 3 impulses Tb / 1.25 VR / 1000 hours, 1000 VRMS for 0.1 s every hour Performance requirements No visible damage ΔC/C0 ≤ 5% Δ tan δ ≤ 0.008 for C ≤ 1 μF Δ tan δ ≤ 0.005 for C > 1 μF Voltage proof Rins ≥ 50% of initial limit No visible damage ΔC/C0 ≤ 10% Δ tan δ ≤ 0.008 for C ≤ 1 μF Δ tan δ ≤ 0.005 for C > 1 μF Voltage proof Rins ≥ 50% of initial limit Passive IEC flammability 60384-14:2013/ AMD1:2016 Flame applied for a period of time depending on capacitor volume B Active IEC flammability 60384-14:2013/ AMD1:2016 20 discharges at 2.5 kV + VR The cheesecloth shall not burn with a flame Mounting guidelines 1 Soldering 1.1 Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature 235 ±5 °C Soldering time 2.0 ±0.5 s Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane Evaluation criteria: Visual inspection Please read Cautions and warnings and Important notes at the end of this document. Wetting of wire surface by new solder ≥90%, free-flowing solder Page 9 of 21 B32911*3 ... B32916*3 X1 / 330 V AC 1.2 Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1. Conditions: Series Solder bath temperature Soldering time MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing >10 mm) MFP MKP (lead spacing >7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤7.5 mm) MKT uncoated (lead spacing ≤10 mm) insulated (B32559) 10 ±1 s 5 ±1 s