B3574

SAW Components Data Sheet B3574 SAW Components Low Loss Filter Data Sheet B3574 868,30 MHz Ceramic package QCC8C Features q RF low-loss filter for remote control receivers q Package for Surface Mounted Technology (SMT) q Balanced and unbalanced operation possible Terminals q Ni, gold plated typ. dimensions in mm, approx. weight 0,1 g Pin configuration 1 2 5 6 7 4,8 3 Input Input Ground or balanced input Output Output Ground or balanced output External coupling coil Case-Ground to be grounded Type B3574 Ordering code B39871-B3574-U310 Marking and package ac- Packing cording too according to C61157–A7–A56 F61074–V8070–Z000 Electrostactic Sensitive Device (ESD) Maximum ratings Operable temperature range TA Storage temperature range DC voltage Source power – 45/+ 95 – 45/+ 95 0 0 ˚C ˚C V dBm Tstg VDC PS 2 Sep 05, 2002 SAW Components Low Loss Filter Data Sheet Characteristics Reference temperature: Terminating source impedance: Terminating load impedance: B3574 868,30 MHz TA = -45 ... 95 ˚C ZS = 50 Ω and matching network ZL = 50 Ω and matching network min. typ. 868,30 max. — MHz Center frequency (center frequency between 3 dB points) fC — Minimum insertion attenuation αmin 868,20 ... 868,40 MHz (including loss in matching coils) Amplitude ripple (p-p) 868,20 ... 868,40 MHz 868,16 ... 868,44 MHz Relative attenuation (relative to αmin) 10,00 ... 600,00 600,00 ... 800,00 800,00 ... 848,00 848,00 ... 863,00 863,00 ... 866,80 870,00 ... 872,00 872,00 ... 882,00 882,00 ...1000,00 αrel MHz MHz MHz MHz MHz MHz MHz MHz — 4,2 5,7 dB — — 0,5 0,7 2,0 3,0 dB dB 60 42 54 51 37 30 47 50 65 47 59 56 42 35 52 55 — — — — — — — — dB dB dB dB dB dB dB dB Impedance for pass band matching 2) Input: ZIN = RIN || CIN Output: ZOUT = ROUT || COUT Temperature coefficient of frequency 1) Frequency inversion point 1)Temperature 2) — — 360 || 1,3 380 || 1,3 -0,03 — — — — 40 Ω || pF Ω || pF ppm/K2 °C TCf T0 — 10 dependance of fC: fC(TA) = fC(T0) (1 + TCf(TA - T0)2) Impedance for passband matching bases on an ideal, perfect matching of the SAW filter to source- and to load impedance (here 50 Ohm). After the SAW filter is removed and input impedance into the input matching / output matching network is calculated. The conjugate complex value of these characteristic impedances are the input and output impedances for flat passband. For more details, we refer to EPCOS application note #4. 3 Sep 05, 2002 SAW Components Low Loss Filter Data Sheet Matching network to 50 Ω (element values depend on pcb layout and equivalent circuit) Ls1 = 18 nH Lp2 = 39 nH Lp3 = 39 nH Ls4 = 18 nH Lk = 12 nH Minimising the crosstalk B3574 868,30 MHz For a good ultimate rejection a low crosstalk is necessary. Low crosstalk can be realised with a good RF layout. The major crosstalk mechanism is caused by the “ground-loop” problem. Grounding loops are created if input-and output transducer GND are connected on the top-side of the PCB and fed to the system grounding plane by a common via hole. To avoid the common ground path, the ground pin of the input- and output transducer are fed to the system ground plane (bottom PCB plane) by their own via hole. The transducers’ grounding pins should be isolated from the upper grounding plane. A common GND inductivity of 0.5nH degrades the ultimate rejection (crosstalk) by 20dB. The optimised PCB layout, including matching network for transformation to 50 Ohm, is shown here. In this PCB layout the grounding loops are minimised to realise good ultimate rejection. Optimised PCB layout for SAW filters in QCC8C package, pinning 1,5 (top side, scale 1:1) The bottom side is a copper plane (system ground area). The input and output grounding pins are isolated and connected to the common ground by separated via holes. For good contact of the upper grounding area with the lower side it is necessary to place enough via holes. 4 Sep 05, 2002 SAW Components Low Loss Filter Data Sheet Normalized frequency response B3574 868,30 MHz Normalized frequency response (wideband) 5 Sep 05, 2002 SAW Components Low Loss Filter Data Sheet B3574 868,30 MHz Published by EPCOS AG Surface Acoustic Wave Components Division, SAW CE AE P.O. Box 80 17 09, 81617 Munich, GERMANY ©.EPCOS AG 2002. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. 6 Sep 05, 2002