B39111-B8100-L100

IF Filters for Cordless Phones and ISM-Band Application Series/Type: B8100 The following products presented in this data sheet are being withdrawn. Ordering Code B39111B8100L100 Substitute Product B39111B4542Z910 Date of Withdrawal 2004-05-19 Deadline Last Orders 2004-09-30 Last Shipments 2004-12-31 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales. The following products presented in this data sheet are being withdrawn: B39111B8100L100 Date of withdrawal: Deadline for last orders: Last shipments: 19−MAY−04 30−SEP−04 31−DEC−04 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of the sales offices are given on the Internet at www.epcos.com/sales. 1 SAW Components Data Sheet B 8100 SAW Components Bandpass Filter Data Sheet B 8100 110,59 MHz duroplast package DIP18D Features s s s s s s IF filter for cordless application Channel selection in DECT system Low group delay ripple Surface Mounted Technology (SMT) Standard IC small outline (SO) package Balanced and unbalanced operation possible Terminals s Tinned CuFe alloyv Dimensions in mm, approx. weight 0,4 g Pin configuration 7 8 16 17 1,4,5,6,9,10 13,14,15,18 2,3,11,12 Input Input ground or balanced input Output Output ground or balanced output Chip carrier – ground not connected Type B8100 Ordering code B39111-B8100-L100 Marking and Package according to C61157-A2-A4 Packing according to F61074-V8058-Z000 Electrostatic Sensitive Device (ESD) Maximum ratings Operable temperature range Storage temperature range DC voltage Source power T Tstg VDC Ps –25/+65 –40/+85 5 10 ˚C ˚C V dBm 2 May 08, 2001 SAW Components Bandpass Filter Data Sheet Characteristics Operating temperature range: Terminating source impedance: Terminating load impedance: B 8100 110,59 MHz T = +25 ˚C ZS = 50 Ω ( 600 Ω || 240 nH*) ZL = 50 Ω ( 140 Ω || 110 nH*) min. typ. 110,59 110,59 20,9 (13,5*) 1,28 2,40 max. — 110,70 22,4 (15,0*) — — MHz MHz dB dB MHz MHz Nominal frequency Center frequency (center frequency between 10 dB points) Insertion attenuation at fN (including losses in matching network) Passband width fN fc αN — 110,48 — — — — B3dB B30dB ∆τ Group delay ripple (p-p) fN - 600 kHz ... fN + 600 kHz αrel — — — — 32 40 45 32 42 48 180 (300*) 2,0 — 38 44 50 38 47 53 250 ns (400*) ns 4,0 10,0 — — — — — — dB dB dB dB dB dB dB dB Relative attenuation (relative to αN) fN - 576 kHz ... fN + 576 kHz fN ± 576 kHz ... fN ± 700 kHz fN ± 1,6 MHz fN ± 3,1 MHz fN ± 4,6 MHz ... ... ... fN ± 3,1 MHz fN ± 4,6 MHz fN ± 20 MHz fN ± 1,728 MHz fN ± 2×1,728 MHz fN ± 3×1,728 MHz Impedance at fN Input: ZIN = RIN || CIN Output: ZOUT = ROUT || COUT Temperature coefficient of frequency — — 600 || 8,5 140 ||19,0 – 18 — — — Ω || pF Ω || pF ppm/K TCf — *) with matching network to 50 Ω (element values depend on PCB layout): Cp1 Ls2 Ls3 Cp4 = 0 pF = 220 nH = 120 nH = 22 pF 3 May 08, 2001 SAW Components Bandpass Filter Data Sheet Transfer function: B 8100 110,59 MHz Transfer function (pass band): 4 May 08, 2001 SAW Components Bandpass Filter Data Sheet Recommended Pin Configurations: For optimum performance use the following pin configurations. Balanced-balanced operation: B 8100 110,59 MHz Balanced-unbalanced operation: Unbalanced-unbalanced operation 5 May 08, 2001 SAW Components Bandpass Filter Data Sheet B 8100 110,59 MHz Matching Stability / Variation of the Matching Network: All matching-elements changed by ±10% (simulation). Transfer function of matched filter (S21): Impedance variation of matched filter (in passband): S11: S22: 6 May 08, 2001